RHINO-RACK 53140 Pioneer Platform Side Rails Instructions

June 12, 2024
RHINO RACK

RHINO-RACK-logo

RHINO-RACK 53140 Pioneer Platform Side Rails

RHINO-RACK-53140-Pioneer-Platform-Side-Rails-product

Product Information

Product Name Pioneer Platform Side Rails
Manufacturer Rhino-Rack
Manufacturer Address (AUSTRALIA) 22A Hanson Pl, Eastern Creek, NSW, 2766
Manufacturer Address (USA) Unit D, 2450 Airport Blvd, Aurora, CO, 80011
Manufacturer Address (CANADA) 19100 Airport Way Pitt Meadows, BC V3Y OE2
Fit Time 30mins
Document No 520-RFI-00005
Issue No 02
Issue Date 16/11/2021

Product Usage Instructions

  1. Check the Rhino-Rack website to ensure you have the latest issue of these instructions.
  2. Refer to your fitting instruction to ensure that the roof racks are installed in the correct locations.
  3. Check the contents of the kit before commencing fitment and report any discrepancies.
  4. Place these instructions in the vehicle’s glove box after installation is complete.
  5. These instructions must be followed for the warranty to be upheld.

Carrying Capacity

Check your vehicle owner’s handbook for the maximum carrying capacity. Load must be evenly distributed over the system.

Rail Model Weight (pair)
53140 2.6kg / 5.7lbs
53146 2.4kg / 5.3lbs
53147 2kg / 4.4lbs

Maximum Strapping Force

  • When strapping to side rails, do not overtighten straps where rail is deformed.
  • If rail begins to deform, loosen the strap. Do NOT strap with ratchet straps on the side rails.

Maximum Pull Force

  • When grabbing to side rails, grab the rail further apart to spread the load through different feet mountings.

Avoid Point Loads

  • Avoid point loads concentrated in the center span. Distribute large loads over the span.

Torque Settings

Unless stated otherwise in these instructions, all fasteners should be set to the following torque settings:

  • M6: 4-5Nm (3-4lbs/ft)
  • M8: 8-10Nm (6-7.5lbs/ft)
  • M10: 16-18Nm (12-13lbs/ft)

Notes for Dealers and Fitters

It is your responsibility to ensure these fitting instructions are given to the end user or client. These instructions remain the property of Rhino-Rack Australia Pty. Ltd. and may not be used or changed for any other purpose than intended.

Important

  1. Check the Rhino-Rack website to ensure you have the latest issue of these instructions.
  2. Please refer to your fitting instruction to ensure that the roof racks are installed in the correct locations.
  3. Check the contents of kit before commencing fitment and report any discrepancies.
  4. Place these instructions in the vehicle’s glove box after installation is complete.
  5. These instructions must be followed for warranty to be upheld.

Fit Time: 30mins

Carrying Capacity

Check your vehicle owners hand book for vehicle maximum carrying capacity. Load must be evenly distributed over the system.

  • 53140: 2.6kg / 5.7lbs
  • 53146: 2.4kg / 5.3lbs
  • 53147: 2kg / 4.4lbs
  • 53141: 3.7kg / 8.2lbs
  • 53142: 4.4kg / 9.7lbs
  • 53144: 3.5kg / 7.7lbs
  • 53145: 3.4kg / 7.5lbs

Precautions

Maximum strapping force = 100kg

RHINO-RACK-53140-Pioneer-Platform-Side-Rails-fig-2

  • When strapping to side rails, do not overtighten straps where rail is deformed. If rail begins to deform loosen strap.
  • Do NOT strap with ratchet straps on the side rails.

Maximum pull force = 200kg

RHINO-RACK-53140-Pioneer-Platform-Side-Rails-fig-3

  • When grabbing to side rails, grab the rail further apart to spread the load through different feet mountings.

RHINO-RACK-53140-Pioneer-Platform-Side-Rails-fig-4

Warning

  • Check part number or kit is correct for use with your vehicle.
  • Do not attempt to fit the system to your vehicle unless you fully understand these fitting instructions. Please direct any questions regarding fitting to the dealer from where the products were purchased.
  • Off-road conditions can be much more rigorous. Extreme care must be taken in off road conditions.
  • Roof racks must be removed when vehicle is put through an automatic car wash.
  • With utility vehicles, the cabin and the canopy move independently. Roof accessories and vehicle can be damaged if the item transported is rigidly fixed at points on both the cabin and canopy. Instead, rigidly fix to either the cabin or the canopy roof racks.
  • Always ensure you fasten your load securely.
  • Use only non-stretch fastening ropes or straps to attach cargo to your load.

In-service maintenance checks

  • All bolt connections should be checked after driving a short distance when you first install your roof racks.
  • All bolted connections should be checked again at regular intervals (weekly is recommended, depending on road conditions, usage, loads and distances travelled).
  • All bolted connections should be checked each time they are re-fitted.

Torque Settings

  • Unless stated otherwise in these instructions, all fasteners should be set to the following torque settings – M6: 4-5Nm (3-4lbs/ft), M8: 8-10Nm (6-7.5lbs/ft) and M10: 16-18Nm (12-13lbs/ft).

Note for Dealers and Fitters

  • It is your responsibility to ensure these fitting instructions are given to the end user or client.
  • These instructions remain the property of Rhino-Rack Australia Pty. Ltd. and may not be used or changed for any other purpose than intended.

Parts List

RHINO-RACK-53140-Pioneer-Platform-Side-Rails-fig-5

Tools Required

  • T1 – Torque tool (Supplied with 5XXXX Series Pioneer Platform)
  • T2 – Tape Measure

Notes

RHINO-RACK-53140-Pioneer-Platform-Side-Rails-fig-6

  • D2 E2 G2 H2 12 Quantities are for the below set upRHINO-RACK-53140-Pioneer-Platform-Side-Rails-fig-7
  • D4 E4 H4 I4 Quantities are for the below set up

Installation Instructions

Platform must be preassembled

RHINO-RACK-53140-Pioneer-Platform-Side-Rails-fig-8

USE FOR SIDE RAIL KIT

  • 53140
  • 53146
  • 53147

USE FOR SIDE RAIL KIT

RHINO-RACK-53140-Pioneer-Platform-Side-Rails-fig-9

  • 53141
  • 53142
  • 53144
  • 53145

RHINO-RACK-53140-Pioneer-Platform-Side-Rails-fig-10 RHINO-RACK-53140-Pioneer-Platform-Side-Rails-
fig-11

RHINO-RACK-53140-Pioneer-Platform-Side-Rails-fig-21

USE FOR SIDE RAIL KIT

  • 53140
  • 53146
  • 53147

USE FOR SIDE RAIL KIT

  • 53141
  • 53142
  • 53144
  • 53145

USE FOR SIDE RAIL KIT

  • 53140
  • 53146
  • 53147

USE FOR SIDE RAIL KIT

  • 53141
  • 53142
  • 53144
  • 53145

USE FOR SIDE RAIL KIT

  • 53140
  • 53146
  • 53147

USE FOR SIDE RAIL KIT

  • 53141
  • 53142
  • 53144
  • 53145

Dimension

  • D E may be adjusted depending on accessories fitted.

RHINO-RACK-53140-Pioneer-Platform-Side-Rails-fig-22

SIDE RAIL KIT| SUITS TRAY LENGTH z (mm)| w (mm)| x (mm)| y (mm)
---|---|---|---|---
53140| 1528|

600

| 414| 602
53146| 1328| 339| 552
53147| 928| 214| 402

RHINO-RACK-53140-Pioneer-Platform-Side-Rails-fig-23

SIDE RAIL KIT| SUITS TRAY LENGTH z (mm)| w (mm)| x (mm)| y (mm)
---|---|---|---|---
53141| 2128|

600

| 344| 390
53142| 2728| 449| 500
53144| 1928| 324| 330
53145| 1828| 294| 320

Repeat 2-9 to opposite side

RHINO-RACK-53140-Pioneer-Platform-Side-Rails-fig-20

Contacts

Rhino-Rack AUSTRALIA

Rhino-Rack USA

Rhino-Rack CANADA

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals