Revel ZAB0125 SPARROW Drone User Manual

: June 13, 2024
: REVEL

Table of Contents

Revel ZAB0125 SPARROW Drone
Product Information
Product Usage Instructions
SAFETY INSTRUCTION
PRODUCT DESCRIPTION
OPERATION
DRONE CONTROL
ADDITIONAL FUNCTIONS
SPECIFICATION
CE DECLARATION OF CONFORMITY
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Revel ZAB0125 SPARROW Drone

Product Information

Product Name: Drone Sparrow
Model Number: ZAB0125
Languages: RO, PL, EN, DE

Product Usage Instructions

Battery Installation:

On the controller, unscrew and remove the battery cover
located on the back of the controller.
Insert 3 x 1.5V AAA batteries with correct polarization.

Flight Preparation:

Press and hold the drone power button for a few seconds. The propellers backlight will blink.
Place the drone on a flat surface with its back facing the user.
Switch the power switch on the controller to the ON position. A beep will be heard and the status indicator will turn on.
To pair the controller with the drone, use the left stick to move forward.

Battery Charging:

Remove the drone’s battery and connect it to the mains charger with a micro USB cable.
During charging, the LED indicator located next to the micro USB port will flash red.
When the battery is fully charged, the indicator will turn green.
Reinstall the fully charged battery on the drone.

Low Battery Alert:

The propeller backlight will flash to indicate low battery level.
Approximately 45 seconds after the low battery alert, the drone will automatically land.
The low battery status will also be signaled with a sound signal.

Take-off and Landing:

To turn on the drone’s motors, press the take-off/landing button or use the left stick to lower its flight until the drone settles on the ground.
To land, press the take-off/landing button or use the left stick to lower its flight until the drone settles on the ground. After this action, the drone’s motors will shut down.
Note: To emergency shut down the motors in flight, press and hold the take-off/landing button for about 3 seconds. The engines will shut down instantly and the drone will fall to the ground.

Drone Control:

Pushing the left stick forward will cause the drone to ascend. Pulling it towards you will cause the drone to descend. Pushing the left stick to the left or right will rotate it in the same direction around its axis.
Pushing the right stick forward will move the drone forward. Pulling it towards you will move the drone backward. Pushing the right stick left or right will move the drone in the same direction.
Pressing the right stick will enter flight calibration (trim) mode. The drone hovers in the air. Pushing the right stick calibrates the hover, depending on the side in which the drone flies independently. Pressing the right stick again disables this mode.

Additional Functions:

To change the backlight mode of the drone’s propellers, press the backlight mode change button.
To perform acrobatics, raise the drone to a height of about 2 meters on the ground. Then, press the drone’s flip button on thecontroller and push the right stick in the direction you want the drone to turn.
Note: this function is unavailable if the drone’s battery is low.
To enable the headless mode, press the headless mode button. Once enabled, no matter how you rotate the drone, its movements will be relative to the controller’s position.

SAFETY INSTRUCTION

Read this instruction manual and keep it for future reference.

Choking hazard! Keep small parts away from children.
Never leave the battery unattended during charging.
Never dispose of battery into a fire.
Follow basic safety rules when operating the device.
Before using the product, make sure that the area you chose is free from obstacles. When operating the product always keep a safe distance from people and animals. Note, to avoid injury or damage, the device should not be flown at shorter distance than 2 meters / 7 feet from people or other obstacles.
Do not operate the product near power lines.
Take extra precaution while using the device.
Do not attempt to repair this device yourself. In case of damage, contact authorized service point for check-up or repair.
When the device is no longer in use, switch it off and then turn off the controller. If the device is not going to be used for a longer period of time, remove batteries from the transmitter.
Do not put the battery in high temperature or near heat sources.
Not suitable for persons under 14 years old. The users under 18 years of age can operate the product under adult supervision only.
Use only authorized accessories.
Don’t over-charge the battery.
Do not touch the motor during or after flights, as it may become hot.
Make sure that the replacement of propellers is done correctly.
Do not use the drone in rain or high wind.
Devices using radio waves can affect the shortened control range of a drone.
When flying a drone, please follow local laws related to unmanned aerial vehicle flying.

PRODUCT DESCRIPTION

Take-off / landing button
Left stick / changing the speed of drone move
Headless mode / rotation button
360° flip button
Right stick / trim button
Changing the drone’s lighting mode
Work status indicator
Power switch
Drone power button

Markings A and B indicate the correct installation of propellers. If necessary, install them according to the diagram shown.

OPERATION

Battery

On the controller, unscrew and remove the battery cover located on the back of the controller. Insert batteries with correct polarization.
Remove the drone’s battery and connect it to the mains charger with a micro USB cable. During charging, the LED indicator located next to the micro USB port will flash red. When the battery is fully charged, the indicator turns green. It needs to be reinstalled on the drone.
Low battery level will be indicated by flashing of the propeller backlight. About 45 seconds after the low battery alert, the drone will automatically land.
Low battery status will be signaled with sound signal.

Flight preparation

Press and hold the drone power button for few seconds. Propellers backlight will blink.
Place the drone on the flat surface with its back to the user.
On the controller, switch the power switch to the ON position. A beep will be heard and the status indicator will turn on.
To pair the controller with the drone, use the left stick to move forward and backward. When paired correctly, the operating status indicator on the controller and the propeller backlight on the drone will be on solid light and a longer sound will be heard on the controller.
The gyroscope inside the drone should be calibrated before each launch. Push the two sticks down to 45° as the picture shows, the propeller backlight will blink and turn solid that indicates the calibration is completed. Correct calibration will be indicated by the solid light of the two propellers.

Take-off and landing

The drone’s motors can be turned on in two ways:
by pointing the sticks down from each other at an angle of 45° -the engines will start to rotate, but the drone will remain on the ground. Then use the left stick by pushing it upwards – the drone will take off to the air.
by pressing the drone’s take-off / landing button – the drone will rise to a height of about 1,5 m.
To land, press the take-off / landing button or use the left stick to lower its flight until the drone settles on the ground. After this action, the drone’s motors will shut down.
Note: To emergency shut down the motors in flight, press and hold take-off / landing button for about 3 seconds. The engines will shut down instantly and the drone will fall to the ground.

DRONE CONTROL

Pushing the left stick forward will cause the drone to ascend. Pulling it toward you will cause the drone to descend.
Pushing the left stick to the left or right will rotate it in the same direction around its axis.
Pushing the right stick forward will move the drone forward. Pulling it toward you will move the drone backward.
Pushing the right stick left or right will move the drone in the same direction.
Pressing the right stick will enter flight calibration (trim) mode. The drone hovers in the air. Pushing the right stick calibrates the hover, depending on the side in which the drone flies independently. Pressing the right stick again disables this mode.

ADDITIONAL FUNCTIONS

Propellers backlight change

To change the backlight mode of the drone’s propellers, press the backlight mode change button.

Acrobatics

Raise the drone to a height of about 2 meters on the ground.
On the controller, press the drone’s flip button.
Then push the right stick in the direction you want the drone to turn.

Note: this function is unavailable if the drone’s battery is low.

Headless mode

Press the headless mode button to turn on this function.
Once the headless function has been enabled, no matter how you rotate the aircraft, the direction to which the user is currently facing when the headlock mode was initialized will be always the heading / forwarding direction for aircraft (front of the drone will be dependent on the remote control). In this way, users don’t have to always keep watching on the aircraft to classify which side is front or which side is back.
To deactivate this mode, press the headless mode button again.

Rotation around its axis

To trigger rapid automatic rotation of the drone, press and hold the headless mode / rotation call button.
The drone will rotate around its own axis.
To deactivate this mode, press and hold the headless mode / rotation call button again.

Changing drone moving speed

To change the speed of the drone, press the left stick.
By default, the drone is set to a low speed.
After the first press, the drone will enter medium speed mode -a double beep will be heard from the controller.
A second press of the button will activate the high-speed mode -a triple beep will be heard from the controller.

Speed	mph	km/h	m/s
Low	1 – 3	1 – 5	0,3 – 1,5
Medium	4 – 7	6 – 11	1,6 – 3,3
High	8 – 12	12 – 19	3,4 – 5,4

SPECIFICATION

6 axis gyro stabilizer
Radical flips & rolls
3 speed modes
Automatic trim function
Headless function (compass)
Indoor/outdoor use
Charging time: ~55 mins
Flying time: up to 7 min
2,4 GHz remote control
Remote control range: up to 80 m
Operation temperature: 0 – 40°C
Drone battery: Li-Po 600 mAh 3,7 V
Charging input: 5 V, 1 A
Controller battery: 3 x 1,5 V AAA battery
Weight: 64 g —
Suitable for persons above 14 years old

LEARN MORE
For more information on this device visit: www.rebelelectro.com.
Read owner’s manual carefully before using your device.
Visit www.rebelelectro.com website for more products and accessories.

Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or Its literature, indicates that It should not be disposed with other household wastes at the end of its working life. To prevent possible harm lo the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract This product should not be mixed with other commercial wastes for disposal.
Made in China for Lechpol Electronics Leszek Sp.k., ul. Garwolińska 1, 08-400 Miętne.

CE DECLARATION OF CONFORMITY

Producer : LECHPOL ELECTRONICS LESZEK
SPÓŁKA KOMANDYTOWA
08-400 Garwolin, Miętne ul. Garwolińska 1

Equipment: Drone
Brand: REBEL
Model: ZAB0119 EAN5901890096188 ZAB0125 EAN5901890035057

We, undersigned, hereby declare that the equipment specified above confirms to the following directives including its newest changes:

ROHS 2011/65/EU appendix II 2015/863
EN IEC 63000:2018
Directive 2009/48/EC of the European Parliament and of the Council
EN IEC 62115:2020+A11:2020
BS EN IEC 62115:2020+A11:2020
EN 71-1+A1:2018
EN 71-2:2020
EN 71-3:2019+A1:2021
RED 2014/53/EU
EN301 489-1V2.2.3 EN301 489-3V2.1.1
EN300 440V2.2.1 EN62479:2010