Dals Lighting ORION DCP-STG48 Outdoor String Light Installation Guide
- June 9, 2024
- dals Lighting
Table of Contents
Installation guide for
ORION
DCP-STG48
| MODEL | WATTS | LUMENS | KELVIN | INPUT | DIMMABLE* |
|---|---|---|---|---|---|
| DCP-STG48 | 24W | 1200lm | ROB + CCT 2200-4000K | 24VDC |
Dals Connect App™
ITEMS INCLUDED IN THE BOX
- Plug-in driver*
- Smart Control box
- 48′ / 15 Bulbs String Light (3.3lbs per set)
- 15 Ferrite ring
*The maximum number of DCP-STR48 sets supported on the included plug-in transformer is 2.
COMPATIBLE ACCESSORIES (SOLD SEPARATELY):
DCP-STGACCBLB: Replacement bulb DCP-STGACCLENS: PCB replacement
WARRANTY / GARANTIE
DALS offers a 5 year warranty from the date of purchase which covers repairs
or replacements of defective parts of the housing, optics, and electronics. To
contact DALS customer service call 1 877 430 1818 or send an e-mail to
info@dals.com.
Installation guide
ORION
DCP-STG48-BK
BEFORE YOU START
BEFORE STARTING INSTALLATION, SHUT THE LINE FEED POWER OFF USING THE CIRCUIT
BREAKER. Instructions pertaining to a risk of fire, electric shock or injury
to persons. Installation must be done according to local electrical codes.
Installation should be done by a certified electrician.
-
Ensure that the plug-in adapter is not plugged in.
-
Use the built-in eyelets to hang your string light bulbs. (Maximum weight of 22 pounds per eyelet)
-
Turn power back on.
For residential installations, we recommend putting the ferrite rings in between each bulb.
-
Localize the clips on the ferrite ‘” ring and lift them to open the ring.
-
Place the ring around the wire, anywhere in-between 2 bulbs and clamp it down.
-
Repeat in between each bulb.
FCC COMPLIANCE
FCC STATEMENT
- This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
- Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
—Consult the dealer or an experienced radio/ TV technician for help.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. In order to avoid the possibility of exceeding the
FCC radio frequency exposure limits, Human proximity to the antenna shall not
be less than 20cm (8 inches) during normal operation
IC COMPLIANCE – CANICES-5()/NMB-5()
Industry Canada Notice This device contains licence-exempt
transmitter(s)/receiver(s) that comply with Innovation, Science and Economic
Development Canada’s licence-exempt RSS(s). Operation is subject to the
following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may
cause undesired operation of the device
2.Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
ISED RF Exposure statement
This equipment complies with ISED radiation exposure limits set forth for an
uncontrolled environment. In order to avoid the possibility of exceeding the
ISED radio frequency exposure limits, Human proximity to the antenna shall not
be less than 20cm (7.9 inches) during normal operation
Dals Connect
To pair your product, follow the steps on the App
1 877 430 1818
www.dals.com
INS_DCP-STG48_REV3
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>