IRAY ILR-1200-3 Laser Rangefinder User Manual
- June 13, 2024
- IRAY
Table of Contents
ILR-1200-3
INFIRAY LASER RANGEFINDER
Product Description
The ILR-1200-3 is suitable not only for InfiRay MATE series products, but also for all day scopes with a 30mm tube for laser ranging.
| Model | ILR-1200-3 |
|---|---|
| Measuring Range, m | 10 ∼ 1200 |
| Laser Wavelength, nm | 900 ∼ 908 (Eye-safe) |
| Laser Indicator | Support |
| Battery | One replaceable CR123 / 3.7V |
| Max. Working Life, h | 4 |
| P Rating | IP67 |
| Laser Class | Class 1 |
| Dimensions, mm | 103x 93 x 30 |
| Weight, g | < 162 (without battery) |
Components and Controls
Battery Installation
-
Rotate the battery compartment cover (1) counterclockwise.
-
Place a CR123 3.7V battery into the compartment according to the label in the battery compartment, that is, the positive pole faces inward and the negative pole faces outward.
-
Tighten the battery compartment cover (1) clockwise.
Safety Instructions -
Use the device within the recommended temperature range from -20°C to +50°C. The battery life may be impaired when using beyond this temperature rang.
-
The battery capacity drops when the device is used below zero. This is normal and does not indicate a defect.
Installation and Calibration
- The ILR-1200-3 comes with a clamp (7) which is suitable for all day scopes with a 30mm tube diameter.
- Install the ILR-1200-3 on the day scope through the 30mm clamp (7), and tighten the mounting screw (8).
- After installation, if the position indicated by the laser is inconsistent with the reticle center on the Tube, the laser calibration is required.
- Select a target that is10Om or 50m away.
- Loosen the two precision adjustment screws (4) on the clamp (7) slightly.
- Then, adjust the angle of the rangefinder until the position indicated by the laser indicator is aligned with the reticle center of the day scope.
- Then tighten the precision adjustment screw (4) to fix.
Use with Day Scope
- Press and hold the Power button (3) for 3 seconds to power on the rangefinder.
- The ILR-1200-3 laser rangefinder supports the continuous scanning mode, and the distance measured will be shown on the display (2).
- When the rangefinder is on, press the Power button (3) one time to turn on or off the laser indicator (5).
- And press the Power button (3) twice in a row to switch the measurement unite between meter and yard.
- After use, press and hold the Power button (3) for 3 seconds to power off it, and the display is off meanwhile.
Use with MATE Series
- Power on the MATE device and get close to the ILR-1200-3.
- Press and hold the Power button (3) to power on the ILR- 1200-3.
- By briefly pressing the Power button (3) of the ILR-1200-3 8 times (or more) in a row, the ILR-1200-3 and the MATE will be connected automatically. After about 5 seconds, the distance can be displayed simultaneously on the displays of the MATE and the ILR-1200-3.
- After connected with MATE, the laser indicator can also be turned on or off with a long press of the UP button on MATE.
Note:
After the first successful connection, the connection between the two
devices will be automatically completed every time when they are powered on.
Legal and Regulatory Information
Wireless transmitter module frequency range: ZIGBEE: 2405-2480 MHz
Wireless transmitter module power < 10 dBm
We, IRay Technology Co., Ltd., hereby declares that the radio equipment
ILR-1200-3 is in compliance with the Directives 2014/53/EU and 2011/65/EU.
User information on the disposal of electrical and electronic devices (private
households)
2012/19/EU (WEEE directive): Products marked with this symbol cannot be
disposed of as unsorted municipal waste in the European Union.
For Proper recycling, return this product to your local supplier upon the
purchase of equivalent new equipment, or dispose of it at designated
collection points. For more more information see:
www.recyclethis.info.
Regulatory information USA
FCC ID: 2AYGT-41-ILR
Labeling requirements
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Information to the user
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
EMC: Class B
Note: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
To comply with RF exposure requirements, a minimum separation distance of 0.00
cm must be maintained between the user’s body and the handset, including the
antenna.
Class 1 Laser Product
Caution: Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radiation exposure.
IRay Technology Co., Ltd.
Add.: 11th Guiyang Street, YEDA, Yantai, P.R. China
Tel: O086-400-999-3800
Email: infirayoutdoor@infiray.com
Web: www.infirayoutdoor.com 
http://www.infirayoutdoor.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>