VISUAL COMFORT CHC 5065 Bayridge Large Pendant User Guide
- June 4, 2024
- VISUAL COMFORT
Table of Contents
VISUAL COMFORT CHC 5065 Bayridge Large Pendant
ASSEMBLY INSTRUCTIONS
NOTICE:
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction and
operation of it, as well as the hazards involved. Inspect item and contents
carefully. If any damage or defect is found, do not install. Retain all
packaging material until installation is complete and approved.
TOOLS REQUIRED (NOT INCLUDED):
- Phillips Screwdriver
- Slip Joint Pliers
- Wire Strippers
- Slotted Screwdriver
- Measuring Tape
- Chain Pliers
- Wire Cutters
-
Carefully remove all parts from the box. Place on a clean, soft surface.
-
Remove mounting plate (B) from canopy (F) by removing collar ring (G).
-
Install mounting plate (B) to the junction box and secure with mounting screws (C).
-
Secure collar loop (D) to mounting plate (B) using pliers to tighten locknut.
-
Install canopy (F) to collar loop (D) and secure with collar ring (G).
-
Install glass shade (L) to metal cap (J) and secure with rubber washer (O) and knurled ring (P).
NOTE: Do not over-tighten otherwise glass could become damaged. -
Install metal ring (Q) and spacers (M) to fixture arm (K) and secure with thumbscrews (N).
-
Feed fixture wire and ground wire through glass shade (L) and metal cap (J), then thread rod (R) to metal cap (J).
-
Install light bulbs into the sockets.
-
Thread rod (T) to bottom center of the cluster (S).
-
Attach rubber washers (V) to either side of glass shade (W) and secure to threaded nipple (U) with metal washer (V1) and knurled ring (X).
NOTE: Do not over-tighten otherwise glass could become damaged. -
Install bottom cap (Y) to threaded nipple (U) and secure with finial (Z).
-
Determine desired overall length, and amount of chain (H) needed. Shorten chain using chain pliers. (Keep extra chain)
-
Attach chain (H) to collar loop (D) and fixture loop (I) using quick links (E). Secure quick links (E).
-
Thread fixture wire and ground wire through chain (H).
NOTE: When you reach the collar loop (D), ensure there is no tension on the wires. Cut excess wires, being sure to leave about 12” to reach the junction box. -
Separate two sides of molded wire, and strip insulation on each 5/8″.
-
Loosen collar ring (G) and let canopy (F) slip down chain (H) carefully.
-
Twist all fixture wires together, and slip through center hole of collar loop (D).
NOTE: Untwist wires and separate to prepare for connection. -
Wrap fixture ground wire (bare copper) around the green grounding screw (see diagram 1). Tighten. Continue fixture ground wire and connect to supply ground wire (usually green or bare copper) using wire nut (A).
NOTE: It is imperative that the fixture is grounded. -
Connect fixture neutral wire (ribbed) to the supply neutral wire (usually white) using wire nut (A).
-
Connect fixture hot wire (smooth with markings) to the supply hot wire (usually black) using wire nut (A).
CAUTION: Do not reverse the hot and neutral connections.
NOTICE:
This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.
Care Instructions: Clean only with a soft dry cloth or feather duster. Do
Not use abrasive or chemical agents.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>