welldana DVS050 DVS Pool Lamps Instruction Manual

DVS050 DVS Pool Lamps
Instruction Manual
VISION SpectraManual
DVS050, DVS100 ,DVS170
DVM050 ,DVM100 , DVM170
Visit www.duratech.be for other available languages

Technical specifications

Lamp Type| Description| Voltage| Power| Color temp| **Luminous flux***
---|---|---|---|---|---
DVS050-RGB
DVS050-TW
DVS050-WH
DVM050-WH| RGB color 50 mm
Tunable white 50mm
Day white 50mm
Low Day white 50mm| 10-14 VAC
10-14 VAC
10-14 VAC
10-14 VAC| 8 W
8 W
10 W
5 W| All colors
2000-17500K
5000K
5000K| 450 lm
550 lm
700 lm
375 lm
DVS100-RGB
DVS100-TW
DVS100-WH
DVM100-WH| RGB color 100mm
Tunable white 100mm
Day white 100mm
Low Day white 100mm| 10-14 VAC
10-14 VAC
10-14 VAC
10-14 VAC| 20 W
20 W
26 W
9 W| All colors
2000-17500K
5000K
5000K| 1550 lm
1500 lm
2300 lm
875 lm
DVS170-RGB
DVS170-TW
DVS170-WH
DVM170-WH
DVM170-RGB| RGB color 170mm
Tunable white 170mm
Day white 170mm
Low Day white 170mm
Low RGB color 170mm| 10-14 VAC
10-14 VAC
10-14 VAC
10-14 VAC
10-14 VAC| 32 W
32 W
40 W
17 W
20 W| All colors
2000-17500K
5000K
5000K
All colors| 2450 lm
2400 lm
3950 lm
1675 lm
1600 lm

(*) Propulsion systems remains a tolerance of +/- 10% on luminous flux measurements @ 25°C ; 12VAC
For operation only with a safety isolation transformer

IEC Protection Class III
Operation on DC voltages is NOT allowed

Maximum water temperature:| +40°C
Lamps have to be kept out of ice zones
---|---
Ingress protection rate:| IP68
measured at 3m max depth = 3m

Remarks

Water conditions
Prevent damage to your pool lamps and wires due to unstable water conditions.
Your local government may have enacted guidelines for your pool water conditions to apply by. If not we strongly advise the following parameter specifications to be applied:

Always adhere to the instructions provided by your chemical brand/supplier for the correct use and application of pool chemicals.
Salt water pools, or pools fitted with a salt water chlorine generator contain salt in the pool water. Salt is a corrosive material. Overdosage and/or consistent levels of salt increase the possibility of deterioration of your pool lamps and cables. As a rule of thumb, a concentration of 35gr/l salt can be accepted when pH values are between 7,2-7,4. In any case, we urge proper use, care and maintenance of your installation, in order to minimize the effect of corrosion and deterioration.
Please be aware that pool lamps and cables with defects caused due to abnormalities in the water condition are not covered by our factory warranty.
Installation/maintenance
The luminaire is maintenance free
If the luminaire needs to be replaced, it needs to be completely removed from the water If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer or his service agent or a similar qualified person in order to avoid hazard
Vision Spectra Pool lamps must be completely submerged into water during operation. Fixing the lamps with adhesives or silicone kit into a niche is not allowed Not following these instructions, will void warranty.

Box contents

Installation instructions

mounting face plate mounting the connector Connector installation

Wiring instructions Setup 1

For new installations
Each lamp is connected to the transformer by a separate cable ** Always use a toroïdal transformer
SELECT CABLE SECTION & MAXIMUM LENGTH**

| LAMP TYPE| 1,5mm 2| 2,5mm2| 4,0mm 2| 6,0mm2| 10mm2| **VA TRANSFORMER (12VAC)***
---|---|---|---|---|---|---|---
| DVS050-TW
DVS050-RGB
DVS050-WH| 75m| 125m| 200m| 300m| 500m| 13 VA
DVM050-WH| 150m| 250m| 400m| 600m| 1000m| 7 VA
| DVS100-TW
DVS100-RGB
DVS100-WH| 25m| 45m| 75m| 115m| 195m| 34 VA
DVM100-WH| 85m| 140m| 200m| 300m| 550m| 12 VA
| DVS170-TW
DVS170-RGB
DVS170-WH| 20m| 30m| 50m| 75m| 125m| 52 VA
DVM170-WH| 45m| 75m| 120m| 180m| 300m| 22 VA
DVM170-RGB| 35m| 60m| 100m| 150m| 250m| 26 VA

STABLE OPERATION OF THE POOL LIGHTS IS ONLY GUARANTEED WHEN THE INSTALLED CABLE CROSS SECTION MATCHES OR EXCEEDS THE ADVISED VALUES IN THE ABOVE TABLE
The transformer VA rating must be greater or equal to the sum of VA ratings of all connected lamps.
These cable lenghts are calculated with worst case voltage drops in the electrical wiring.

Wiring instructions Setup 2

For existing or other installations
All lamps are connected to the transformer via 1 cable **** Always use a toroïdal transformer

SELECT CABLE SECTION & MAXIMUM LENGTH

| LAMP TYPE| QTY| 2,5mm2| 4,0mm 2| 6,0mm 2| 10mm 2| VA TRANSFORMER (12VAC)
---|---|---|---|---|---|---|---
| DVS050-TW
DVS050-RGB
DVS050-WH| 1
2
3
4| 125m
63m
42m
31m| 200m
100m
67m
50m| 300m
150m
100m
75m| 500m
250m
167m
125m| 13
26
39
52
DVM050-WH| 1
2
3
4| 250m
125m
83m
63m| 400m
200m
133m
100m| 600m
300m
200m
150m| 1000m
500m
333m
250m| 7
14
21
28
| DVS100-TW
DVS100-RGB
DVS100-WH| 1
2
3
4| 45m
23m
15m
11m| 75m
38m
25m
19m| 115m
58m
38m
29m| 195m
98m
65m
49m| 34
68
102
136
DVM100-WH| 1
2
3
4| 140m
70m
47m
35m| 75m
38m
25m
19m| 300m
150m
100m
75m| 550m
275m
183m
138m| 12
24
36
48
| DVS170-TW
DVS170-RGB
DVS170-WH| 1
2
3
4| 30m
15m
10m
8m| 50m
25m
17m
13m| 75m
38m
25m
19m| 125m
63m
42m
31m| 52
104
156
208
DVM170-WH| 1
2
3
4| 75m
38m
25m
19m| 120m
60m
40m
30m| 180m
90m
60m
45m| 300m
150m
100m
75m| 22
44
66
88
DVM170-RGB| 1
2
3
4| 60m
30m
20m
15m| 100m
50m
33m
25m| 150m
75m
50m
38m| 250m
125m
83m
63m| 26
52
78
104

STABLE OPERATION OF THE POOL LIGHTS IS ONLY GUARANTEED WHEN THE INSTALLED CABLE CROSS SECTION MATCHES OR EXCEEDS THE ADVISED VALUES IN THE ABOVE TABLE

Retrofit in PAR56 niche (only Vision Spectra 170mm)

Color programs

RGB LAMPS

TW LAMPS

Synchronizing & color changing (for RGB and TW lamps only)

Manual synchronization

1. Switch ON the 12 VAC line voltage and make sure that all lamps light up.
2. Switch OFF the 12 VAC line voltage and wait for at least 20 sec (max 60 sec)
3. Switch ON and switch OFF (max 3 sec ON and max 3 sec OFF)
4. Switch ON and switch OFF (max 3 sec ON and max 3 sec OFF)
5. Switch ON
6. The lamps should now all be on color program 6: Blue

• TW lamps: the lamps will all flicker after 15 seconds on color program 6. You can now choose to lock the lamp on a desired color program by switching off/on within the next 5 seconds. After 5 seconds the flickering will stop and the lamp is locked.
  See next page for details. If you did not select a color when flickering, the lamps will stop flickering after 5 seconds and the lamp will be unlocked.

Changing colors
Quickly turn the lamps OFF and back ON
The lamp will jump to the next color program
Memorizing the actual color
Turn the lamp OFF for MINIMUM 20 seconds
The last chosen color has now been memorized

Color Locking (only for TW lamps)

If desired, TW lamps can be “locked” on a color program of choice. This means the lamp will only light up in that specific color, and it is no longer possible to change the color program of the lamp.
This process can be reversed anytime by “unlocking” the color program. All color programs will then be available again, and can be changed at any time.
Locking/Unlocking procedure
Locking the color of a lamp starts with a synchronisation procedure:

1. Switch ON the 12 VAC line voltage
2. Switch OFF the 12 VAC line voltage and wait for at least 20 sec (max 60 sec)
3. Switch ON and switch OFF (max 3 sec ON and max 3 sec OFF)
4. Switch ON and switch OFF (max 3 sec ON and max 3 sec OFF)
5. Switch ON
6. Wait for about 15 seconds. The lamp(s) will now flicker
   LOCKING: – during the flickering of the lamp, select the desired color program by  switching (within 5 seconds) the lamps OFF and ON quickly.
   – When the right color is selected, then wait 5 seconds, until the flickering stops
   – The lamp is now locked on the chosen color program
   UNLOCKING: – When the lamps flicker, then do nothing for 5 seconds.
   – The flickering will stop, and it is again possible to change the color program of the lamps.

Troubleshooting

color program
2. Remove the lamp from the water, unscrew the fix nut, pull back the gasket and the black cable jacket, so you can reach the brass contacts inside the connector block (do not remove the connector block)
3. Measure the voltage at the lamp terminals (while the lamp is still ON)
4. The voltage at the lamp should be at least 10VAC 50Hz. If the measured line voltage is below 10VAC:
A. Check the output voltage at the transformator terminals. This voltage should be between 12VAC and 14VAC. Verify that the used transformator VA rating is sufficient for powering all connected lamps
B. If the transformator output voltage is ok, then install a thicker cable between the transformator and the lamp. (wiring instructions p. 10-13)
In case of TW lamps: make sure the lamp is not in color locking mode
Several pool lights in the pool show different
color programs| Make sure that all lamps are connected to the same 12VAC power line. Execute the synchronization as explained on p.16

Declaraction of Conformity
Declarations of conformity covering this product are available for download from the House of Duratech website: www.duratech.be

Contact details
Propulsion Systems bv
Dooren 72
1785 Merchtem, Belgium
Tel +32 2 461 02 53
www.duratech.be
info@propulsionsystems.be
http://www.propulsionsystems.be
We reserve the rights to change all or part of the contents of this document without prior notice

References

• Duratech | Home

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>