saxby lighting 107125 RularPLUS LED Batten Instruction Manual

saxby lighting 107125 RularPLUS LED Batten

Thank you for purchasing this light fitting. Please read the instructions carefully before use to ensure safe and satisfactory operation of this product. Please retain these instructions for future reference.

Technical data

• Supply Voltage: 220-240 V~, 50 Hz
• Bulb Type:
  • 107125 : 20W LED module (SMD), 4000K
  • 107126 : 26W LED module (SMD), 4000K
  • 107127 : 35W LED module (SMD), 4000K
  • 107128 : 31.5W LED module (SMD), 4000K
  • 107129 : 39W LED module (SMD), 4000K
  • 107130 : 44W LED module (SMD), 4000K

Warning:

This is a Class 1 product and must be earthed.

• Please read these instructions carefully before commencing any work.
• This unit must be fitted by a competent and qualified electrician.
• Check the pack and make sure you have all the parts listed.
• Install in accordance with the IEE Wiring regulations and current Building Regulations.
• To prevent electrocution switch off at mains supply before installing or maintaining this fitting. Ensure other persons cannot restore the electrical supply without your knowledge. If you are in any doubt, please consult a qualified electrician.
• This light fitting should be connected to a fused circuit.
• If replacing an existing fitting, make a careful note of the connections.
• This product contains non-replaceable parts and cannot be serviced. If damage occurs the part should be scrapped.
• Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.

Layout

Plan the desired layout of these fittings carefully, ensuring the cables will reach the distances between the junction box and the each light fitting. Avoid locating any cables in positions that would cause a hazard. Position cables and outdoor rated junction boxes (not supplied) away from areas where they may be at risk from being cut, trapped or damaged. The mains supply cable must have a minimum cross section area of 1.0mm2. Cables must be protected using suitable conduit or plastic trunking. Take care not to drill into any pipes or mains cables beneath the surface during mounting holes preparation. This product can be installed on the ceiling or wall.

Installation

Existing fittings must be completely removed before installation of a new product. Before removing the existing fitting, carefully note the position of each set of wires. Note that the switch is turned off before installation. The mounting surface must be flat and smooth to ensure a good fit.

• Hold the product in place and mark the position of the fixing holes. This may require the help of an assistant. If wall mounting, ensure that the product is level.
• Take care to avoid damaging any concealed wiring and pipes. The correct fixings should be used for bricks, cavity walls or plasterboard.
• Ensure the ceiling or wall is capable of holding the weight of the product and then fix brackets in place.
• Rotate both ends of the product in the direction of the arrow to open the diffuser cover.
• Pull the supply cable through the middle grommet and fix the light fitting into position using appropriate fixings.
• Connect the supply cable to the quick fit terminal block as detailed wiring diagram.
• Close diffuser cover into place.
• Replace fuse or circuit breaker and switch on. Your light is now ready for use.

Wiring:

This product is Class I product must be earthed. They must be joined together and well insulated with good quality insulation tape. This is to ensure earth continuity throughout your property.  Having correctly identified the wiring from your existing light fitting and connect to the connection block inside the product in the following way:

Check that…

• You have correctly identified the wires.
• The connections are tight.
• No loose strands have been left out of the connection block.

Care and Safety

Live Voltages may be present in this unit even when turned off or when completely disconnected. We recommend cleaning with a soft dry cloth. Do not use solvents or abrasive cleaners as these could damage the finish. For your safety, always switch off the power supply before cleaning.

For further information, please visit https://www.lighting- info.co.uk/107125
V1 25/05/2023
UK Manufacturer: BH17 7BY
EU Manufacturer: Brilliant AG,
Brilliantstrasse 1, D-27442 Gnarrenburg

Documents / Resources

| saxby lighting 107125 RularPLUS LED Batten [pdf] Instruction Manual
107125 RularPLUS LED Batten, 107125, RularPLUS LED Batten, LED Batten, Batten
---|---

References

• Saxby Lighting - Commercial and Domestic Lighting Supplier
• Directory Contents

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>