Aaobosi B0CBXGK682 12 Volt Car Refrigerator User Manual
- June 13, 2024
- Aaobosi
Table of Contents
Aaobosi B0CBXGK682 12 Volt Car Refrigerator User Manual
Safety Instructions
WARNING! Failure to obey these warnings could result in malfunction of your device and possible injury for yourself and other users.
- Do not operate the device if it is visibly damaged.
- Do not block the gaps of the device with things like pin, wire, etc.
- Do not expose the device to rain or soak it in water.
- Do not place the device near naked flames or other heat sources (heaters, direct sunlight, gas ovens etc.)
- Do not store explosive substances like spray cans with flammable propellants in the device.
- Before starting the device, ensure that the power supply line and the plug are dry.
- Check if the voltage specification on the type plate matches that of the energy supply.
- Once unpacked and before turning on, the device must be placed on a level surface for more than 6 hours.
- Make sure that the device stays horizontally when it is running. The tilt angle must be less than 5° for long time running and be less than 45° for short time running.
- The refrigerator must be well ventilated for heat dissipation and make sure to keep some space around it. (Back Space~200mm, Side Space~lO0mm)
- The device may only be repaired by qualified personnel. Improper repairs can lead to safety hazards. If the power cable is damaged, it must be replaced by the manufacturer, customer service or a similarly qualified person in order to prevent safety hazards.
NOTICE!
- The device can be used by children aged 8 or over, as well as by persons with reduced physical, sensory or mental capabilities or a lack of experience and/or knowledge, providing they are supervised or have been taught how to use the device safely and are aware of the resulting risks.
- Children must be supervised to ensure that they do not play with the device.
- The installation of DC power in the boat must be handled by qualified electricians.
- Never pull the plug out of the socket by the cable.
- Disconnect the device or switch it off when you turn off the engine. Otherwise you may discharge the battery.
CAUTION!
- Food is suggested to be stored in its original packaging or in suitable containers.
- Set suitable temperature for food or medicine stored in the device. Refer to recommended temperature for common food on Page4.
Product Features
- High-efficiency DC compressor and conversion module.
- CFC free and great heat insulation.
- DC12/24V or AC 100~240V (using the adapter) power supply.
- Fast cooling to -20°C/-4°F(based on 25°C/77°F room temperature).
- Intelligent battery protection system.
- Digital display for temperature setting.
- Cup holder design and adjustable door opening direction.
Product Structure
Reverse door open direction
The door has two opening directions and can be taken off at an angle of 20°. When installing it back, align the door shaft with the compartment hole and then insert it.
APP Connection
Scan the QR Code with your smartphone or search it in the APP Store or Google Play to download the “QZsmart” app.
PREPARATION BEFORE USE:
-
Make sure your car fridge is on and ensure that your smartphone is connected to 2.4 GHz Wi-Fi network.
NOTE: This device works only on 2.4 GHz Wi-Fi® network. -
Ensure that the Bluetooth function of the mobile phone is enabled at the same time; otherwise, the device cannot be automatically searched.
-
Download the QZsmart app from the App Store or Google Play™.
NOTE: Authorize the app to access network and location services. -
If you are using the app for the first time, click the “Sign up” button and register. If you already have an account, click the “Log in” button.
-
For better WIFI connection, please reset the product WIFI before using it for the first time.
You can disconnect the connection by turning off the switch of the refrigerator and simultaneously long pressing and on the control panel of the refrigerator for 3 seconds and hearing one beep.
Add Device
-
From the Home Page, press “Add Device” or press in the top right corner of the screen.
(If you already have a device added to your account, the “Add Device” button will not appear). -
Connecting
♦ Auto-connect: (Featured First)
The app will automatically search when Wi-Fi and Bluetooth are switched on, so
you can add the corresponding product directly from the automatic search.
Step 1：Press “Add Device” or press “ “.
Step 2：When the device is found, press Add. The Bluetooth function must be
enabled during this process.
Step 3：Select your Wi-Fi network. (Be sure to use a 2.4G network）
Step 4：Enter your router password.
Step 5：Wait for connection and click “NEXT”.
Step 6：Once the device is added, you can use the menu to change the name and
location of the device.
Step 7：When you are finished, click “Done”.
♦ Manual connection: Select your model from the device menu.
Step 1：Press “Add Device” or press “ “.
Step 2：Select the corresponding product type and click the product diagram of
the corresponding model.
Step 3：After the product is shut down, press ” Next “.
Step 4： Long pressing ” “and” – ” on the control panel of the refrigerator for
3 seconds and hearing one beep, Press “Next”.
Step 5：Select your Wi-Fi network（. Be sure to use a 2.4G network）
Step 6：Enter your router password.
Step 7：Click “Confirm.” The next screen will say “Connect your mobile phone to
the device’s hotspot.”
Step 8：Click “Go to connect.” This will take you to your phone’s settings (or
Wi-Fi list for Android).
Step 9：Select “SmartLife-XXXX.”
Step 10：Navigate back to the QZsmart App.
Step 11：Click “Next.” Your smartphone will automatically connect.
Step 12：Once the device is added, you can use the menu to change the name and
location of the device.
Step 13：When you are finished, click “Done.”
♦ Follow the APP interface, there are detailed operation reminders in the APP
interface, you
need to follow the steps one by one.
NOTE : Connection may take up to 60 seconds.
Once the device is added, you can use the menu of the app to change the name of the device.
When you finished, press “Done”.
NOTE : Your mobile device is connected to a 2.4GHz Wi-Fi network when
pairing with the app.
Please select the 2.4GHz network when selecting a Wi-Fi network on the app
during setup.
Using the My App
The main interface can control the switch, set “temperature” and “lock”.
Click on “more features” in the lower right corner to set the switch of
temperature unit, cooling mode, battery protection mode.
How to unbind
A car refrigerator can only be connected to one mobile phone.
First method: You can disconnect the connection by turning off the switch
of the refrigerator and simultaneously long pressing and on the control panel
of the refrigerator for 3 seconds and hearing one beep.
Second method: Removing connection with the app: Open the app and go to the device page Click “ ” in the upper right corner, and then click “Remove Device” at the bottom.
Cautions
There will be a delay in operating the machine on the mobile phone, about 1-3 minutes, please be patient.
The language of the APP automatically switches with the language of the mobile system.
*You can lock or unlock the control panel on the refrigerator by operating the APP lock icon.
Please note that if you want to lock the refrigerator, please control it
through the APP, the operation panel of the refrigerator does not have the
function of locking and unlocking.
*This product includes WIFI plus Bluetooth function. Bluetooth function can be used in non-wifi environment. If you need to use Bluetooth function, please be sure to connect WIFI, successfully for the first time. (Again, you must connect to WIFI first, otherwise you will not be able to use Bluetooth in non-wifi environments.)
Function and Operation
- Power supply: connect to DC 12V/24V or AC 100~240V (using the adapter) power supply.
- Power On/Off: press to switch ON/OFF. (Power light in red: compressor shutdown or delay start; power light in green: compressor is working)
- Temperature Setting: press + or – for temperature setting, the setting will be saved automatically after stopping operating for 4 seconds(Note: the temperature displayed is the current temperature of the compartment, it’ II take a while to reach the set temperature.) Temperature setting range: -20~20°C (-4~68°F)
- Cooling Mode: under the running state, press to switch HH(fast cooling mode, Eco/Max light in red) and ECO(Energy saving mode, Eco/Max light in green). (*Factory setting is HH.}
- Temperature Unit Setting: switch off the fridge, long press for three seconds until El displays, keep pressing until ES displays. then press + or – to select Celsius or Fahrenheit.(*Factory setting is °C.)
- Battery Protection Mode: under the running state, long press for three seconds until screen flashes, then press again to select protection mode H3(High), H2(Middle) and Hl(Low) (*Factory setting is H3.)
Due to the different output voltages between vehicles, H3 should be set when
the product is connected to car power, and H2 or Hl should be set when it is
connected to a portable battery or other back-up battery.
The battery gear should be set from H3 to H2 or from H2 to Hl if there is a
voltage protection code Fl shown on the panel. The battery gear should be set
to H if the product keeps working after turning off the car engine, or the
product may drain the battery.
Voltage Reference:
*the voltage is theoretical value, there may be a deviation in different sceneries.
• Reset : switch off the fridge, long press for three seconds until El
displays, under El mode, long press + – at the same time until the screen
displays “888”.
♦ Recommended temperature for common food:
Cleaning and Storage
■ Cleaning:
- Unplug the device first to avoid electric shock.
- Use wet cloth to clean the device and dry it.
- Do not soak the device in water and do not wash it directly.
- Do not use abrasive cleaning agents as these can damage the device.
■ Storage:
If the device will not be in use for a long time, please follow the steps:
- Turn off the power and remove the plug.
- Remove all the items stored in the device.
- Wipe off excess water from the fridge with a soft rag.
- Put the device in a cool and dry place.
- Leave the door slightly open to prevent odors from forming.
■ Defrosting:
Humidity can form frost in the interior of the cooling device or on the
evaporator.
This reduces the cooling capacity. Defrost the device in good time to avoid
this.
- Switch off the device.
- Take out the contents of the device.
- Keep the door open.
- Wipe off the defrosted water.
Never use hard or sharp tools to remove ice or to loosen objects which have frozen in place.
Troubleshooting
Technical Information
*Due to product improvement, the technical information might be different from actual information, please refer to the rating label on the product.
■ Disposal:
This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling.
Warranty card
Thank you for choosing AOBOSI product. We sincerely hope that you are
satisfied with it.
The manufacturer’s warranty covers the product for a period of 12 months from
the date of purchase against manufacturing faults. All warranties are
automatically kept track of in our system, so there is no need to register
your product.
Agent/Distributor is welcome to contact us. Email:[email protected].
Any help or questions during use, please contact us via websitewww.iaobosi.com, send **email to [email protected],** we will service you withi 24 hours. We suggest to provide a warranty card, a photo or a video if there’s broken spare part or not working machine so that we can be much more clear about your problems and offer you the best solution.
Please fill in the table and email it within 10 days from the date of purchase .