ComXim 2BB29-RUPSL Electric Turntable Instructions
- June 13, 2024
- ComXim
Table of Contents
ComXim 2BB29-RUPSL Electric Turntable
Product Information
The ComXim intelligent turntable is designed for product rotation, display, 360-degree shooting, and 3D scanning. It is available in various models with different specifications:
- MT200RL20x: Voltage – 20-68 (S/Lap), Max Load – 20 Kg
- MT320RL40x: Voltage – 25-72 (S/Lap), Max Load – 40 Kg
- MT350RL40x: Voltage – 28-74 (S/Lap), Max Load – 40 Kg
- MT400RL40x: Voltage – 27-76 (S/Lap), Max Load – 40 Kg
- MT500RL200x: Voltage – 34-90 (S/Lap), Max Load – 200 Kg
- NT600RL200x: Voltage – 34-90 (S/Lap), Max Load – 200 Kg
- MT800RL300x: Voltage – 55-140 (S/Lap), Max Load – 300 Kg
The turntables support three rotation modes: continuous, intermittent, and left-and-right swing.
Product Usage Instructions
To use the ComXim intelligent turntable:
- Plug in the power supply.
- Turn on the turntable.
- Use the remote control to control the rotation modes, rotation speeds, and rotation angles.
Small Remote Controller Instructions
Use the small remote controller to control the turntable. The buttons on the remote control allow you to:
- Speed up clockwise rotation.
- Speed down clockwise rotation.
- Save current settings.
- Start/pause counterclockwise rotation.
Medium Remote Controller Instructions
Use the medium remote controller to control the turntable. The buttons on the remote control allow you to:
- Save current settings to the turntable flash.
- Lock the settings.
- Control the turntable to output the focus signal.
- Rotate the turntable by a specific angle (e.g., 0.1 degrees, 0.5 degrees, 5.625 degrees).
- Control the turntable to return to the original position.
- Control the turntable to rotate counter-clockwise.
- Control the turntable speed decrease.
- Control the turntable to rotate intermittently.
- Control the turntable to output the focus signal and the shutter signal (supported only by specific models).
- Control the turntable to output the shutter signal (supported only by specific models).
Large Remote Controller Instructions
Use the large remote controller to control the turntable. The buttons on the remote control allow you to:
- Lock the settings.
- Save current settings.
- Rotate the turntable by a specific angle using hot keys.
- Rotate the turntable back to the original position.
- Plug in power supply and turn on the turntable.
- Use the remote control to control the rotation modes, rotation speeds and rotation angles.)
- This Series of electric turntables support 3 rotation modes: continuous, intermittent and left-and-right swing.
Product parameters
Item No. /Voltage /Speed（S/Lap） /Max Load（Kg）
- MT200RL20x/100V – 240vAC/ 20-68(S/Lap)/ 20 Kg
- MT320RL40x/100V – 240vAC/ 25-72(S/Lap)/ 40 Kg
- MT350RL40x/100V – 240vAC/ 28-74(S/Lap)/ 40 Kg
- MT400RL40x/100V – 240vAC/ 27-76(S/Lap)/ 40 Kg
- NT400RL40x/100V – 240vAC/ 25-72(S/Lap)/ 40 Kg
- MT500RL200x/100V – 240vAC/ 34-90(S/Lap)/ 200 Kg
- NT600RL200x/100V – 240vAC/ 34-90 (S/Lap)/ 200 Kg
- MT800RL300x/100V – 240vAC/ 55-140(S/Lap)/ 300 Kg
MT Series turntable model maming rules, identification and main characteristics
Remote Instructions
Small remote controller instructions
Note: ACR2025 button battery is used to provide power for the remote controller.
Medium remote controller instructions
Note: AAA battery is used to provide power for the remote controller.
Large remote controller instructions
Note: AAA battery is used to provide power for the remote controller.
Precautions
- Attention: Electric turntables are of electric products. They are Not waterproof and not heat resistant.
- In cases when turntable doesn’t work, please check whether the turntable is powered on, whether the power cord is plugged in tightly, and whether the switch is turned on. If the turntable still cannot work normally, please contact us.
- The load-bearing capacity of the turntable refers to the maximum load that the turntable can bear when the item is smaller than the diameter of the turntable. If the item exceeds the diameter of the turntable, the load-bearing capacity will be greatly reduced, and even it will not turn.
- In order to prolong the service life of the turntable, it is recommended to stop for 2 hours after working continuously for 8 hours.
- In order to protect the safety of users, unauthorized modification or repair of the product is prohibited. Please contact us if necessary.
Notes
FCC STATEMENT
Labelling requirements
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference
- This device must accept any interference received, including interference that may cause undesired operation.
15.21 Information to user
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
15.105 Information to the user
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver isconnected. -Consult the dealer or an experienced radio/TV technician for help.
RF warning for Mobile device: This equipment complies with FCC radiation exposurelimits set forth for an uncontrolled environment. This equipment should be installed and operated withminimum distance 20cm between the radiator & your body.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>