ComXim MT200RL20x Electric Turntable Instruction Manual

June 13, 2024
ComXim

ComXim MT200RL20x Electric Turntable

ComXim-MT200RL20x-Electric-Turntable-product

Product Information

The ComXim intelligent turntable is designed for product rotation display, 360-degree shooting, and 3D scanning. It comes in different models with varying specifications and features.

Product Parameters

Item No. Voltage Speed (S/Lap) Max Load (Kg)
MT200RL20x 20-68 20 Kg
MT320RL40x 25-72 40 Kg
MT350RL40x 28-74 40 Kg
MT400RL40x 27-76 40 Kg
NT400RL40x 25-72 40 Kg
MT500RL200x 34-90 200 Kg
NT600RL200x 34-90 200 Kg
MT800RL300x 55-140 300 Kg

MT Series Turntable Model Naming Rules

The MT series turntable model naming follows the pattern of “MT + Series Name

  • Turntable Model Code + Diameter (cm) + Sub Code + Max Load (Kg)”. The sub code can be RL, L20, or L40, indicating different variations of the model.

Product Usage Instructions

Small Remote Controller Instructions

  • Speed Up: Clockwise rotation speed increase.
  • Speed   Down: Clockwise rotation speed decrease.
  • Save: Store the current settings to the turntable flash.
  • Counterclockwise Rotation Start/Pause: Start or pause counterclockwise rotation.

Medium Remote Controller Instructions

  • Save: Store the current settings to the turntable flash.
  • Lock: Invalidates all keys except this button.
  • Focus: Control the turntable to output the focus signal.
  • Single Rotation: Pressing the buttons in this group rotates the turntable once based on the specified angle. Different buttons correspond to different rotation angles.
  • Return to   the Origin: Control the turntable to return to the original position.
  • Counter Clockwise Rotation: Control the turntable to rotate counterclockwise.
  • Slow Down: Control the turntable speed decrease.
  • Intermittent Rotation: Control the turntable to rotate intermittently.
  • Auto: Control the turntable to output the focus signal and the shutter signal.
  • Shutter: Control the turntable to output the shutter signal.

Large Remote Controller Instructions

  • Lock: Invalidates all keys except this button.
  • Original Position Setting: Set the current position as the original position.
  • Save: Save the current settings.
  • Hot Keys: Press any key in this group, and the turntable rotates the corresponding angle once.
  • Original Position: Turntable rotates back to the original position.

Precautions

No specific precautions were mentioned in the user manual.
Please refer to the manufacturer’s website or contact customer support for any additional instructions or safety guidelines.

  1. Plug in power supply and turn on the turntable.
  2. Use the remote control to control the rotation modes, rotation speeds and rotation angles.)
  3. This Series of electric turntables support 3 rotation modes: continuous, intermittent and left-and-right swing.

Product parameters

ComXim-MT200RL20x-Electric-Turntable-
fig-5

MT Series turntable model maming rules, identification and main characteristicsComXim-MT200RL20x-Electric-Turntable-
fig-6

Small remote controller instructions

Note: ACR2025 bu on ba ery is used to provide power for the remote controller.

Medium remote controller instructions

ComXim-MT200RL20x-Electric-
Turntable-fig-2

Note: AAA ba ery is used to provide power for the remote controller.

Large remote controller instructions

ComXim-MT200RL20x-Electric-
Turntable-fig-3

Precautions

  1. Attention: Electric turntables are of electric products. They are Not waterproof and not heat resistant.
  2. In cases when turntable doesn’t work, please check whether the turntable is powered on, whether the power cord is plugged in tightly, and whether the switch is turned on. If the turntable still cannot work normally, please contact us.
  3. The load-bearing capacity of the turntable refers to the maximum load that the turntable can bear when the item is smaller than the diameter of the turntable. If the item exceeds the diameter of the turntable, the load-bearing capacity will be greatly reduced, and even it will not turn.
  4. In order to prolong the service life of the turntable, it is recommended to stop for 2 hours after working continuously for 8 hours.
  5. In order to protect the safety of users, unauthorized modification or repair of the product is prohibited. Please contact us if necessary.

Notes

FCC

Labelling requirements. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference,
  2. this device must accept any interference received, including interference that may cause undesired operation.

Information to user.Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment Information to the user.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

RF warning for Mobile device:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. Thisequipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Copyright reserved by Shenzhen ComXim Technologies Co.,Ltd.2023
www.comxim.com

Documents / Resources

| ComXim MT200RL20x Electric Turntable [pdf] Instruction Manual
MT200RL20x, MT320RL40x, MT350RL40x, MT400RL40x, NT400RL40x, MT500RL200x, NT600RL200x, MT800RL300x, MT200RL20x Electric Turntable, Electric Turntable, Turntable
---|---

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals