Rasonic RIC-S228E Kitchen Use Double Burner Induction Cooker Instruction Manual
- June 4, 2024
- Rasonic
Table of Contents
RIC-S228E / RIC-S211E
Kitchen Use Double-Burner Induction Cooker
For household use only
Installation Instruction
- Please read the installation instruction carefully before using and well keep it in a safe place for future reference.
- Some figures in this instruction may not match with the real object, just for reference only.
Kitchen Use Double-Burner Induction Cooker
Thank you for purchasing Rasonic Kitchen Use Double-Burner Induction Cooker. Read the installation instruction carefully before installation and well keep it for your future reference.
Safety Precautions
-
Accessories
a. A copy of the operation manual and installation instructions
b. A copy of warranty registration card
c. A bundle of foam adhesive tape -
Do not disassemble the top plate during installation.
-
Do not install the appliance over a dishwasher, washing machine, dryer, electric oven or refrigerator.
-
Make sure to have a trial test and give an appropriate demonstration to the end user before installing the appliance. For built-in installation, leave at least 100 mm space at the sides, front and back from the wall. Also, at least 150 mm height and 80 cm? should be reserved for air inlet exhaust space. For free-standing installation, leaving at least 100 mm space at the sides, front and back from the wall.
-
Follow the instruction when installing the appliance. If improperly installed, it may cause electric leakage or lead to overheating. Connect the original power cord with plug to an independent 13A socket. If fixed connection wiring is needed, disconnection must be incorporating an independent switch with 13A or above in accordance with the Electricity Ordinance.
-
If dedicated circuit wiring is connected incompatibly, it may probably lead to abnormal raise of wiring temperature.
-
Installation should be done by a qualified electrician. If the connection or repair is finished improperly, it may cause electric leakage, malfunction or hazard.
-
Never disassemble, repair or modify the appliance by yourself. Attempting to do so may cause the appliance to have an abnormal operation or cause hazards.
-
Install the grounding completely with the related ordinances. Installation of grounding can avoid electric shock once electric leakage occurs.
-
The grounding should be installed by a qualified electrician, avoiding electric shock during electrical leakage.
-
If the power cord is damaged, it must be replaced by Shun Hing Electric Service Centre Ltd. in order to avoid hazards.
-
Do not step on or drop any hard objects on the top plate. If it is cracked or broken, it may cause overheating, abnormal operation or electric shock.
-
Do not touch the top plate or other heating areas during operation. It may cause bum or other hazards.
-
Use heat-resistant materials for the countertop where it should be the same or better than a thermosetting high-pressure decorative sheet. If the materials are not heat resistant, it may cause deformation or fire. Do not use vanished materials as they may cause discoloration.
Product Installation Dimensions
(Unit: mm)
Customize Kitchen Cabinet (Built-in)
3.1 Adhesive tape
The supplied adhesive tape is about 2.5 meters long. Cut off 90° (Diagram 1)
of the adhesive tape and fold it into an inner angle 90° (Diagram 2), then
remove the protective paper of the adhesive tape, and adhere to the
surrounding of the countertop. Remove the protection paper from the other side
of the adhesive tape, then place the appliance on top of the countertop
accurately and compress tightly.
* Note:** Stick the adhesive tape around the countertop. Do not cut it
apart; otherwise, it may influence the sealing performance.
3.2 Ensure the space of intake to the cabinet and the space at bottom of the
appliance are correct for sufficient ventilation.
Insert the appliance backside into the countertop first and
fit the whole unit.
- Do not drop the appliance onto the countertop.
- Confirm the clearance distance between the bottom frame and the countertop are exactly the same from front to back and from side to side.
- If the power cord is trapped between the cabinet and the bottom side of the appliance, the existence of an uneven gap may cause vibration.
- If there is a bulge on the countertop, do not install the appliance on top of it.
- Place the appliance horizontally into the installation hole and make sure the appliance is installed evenly and stable.
3.3 If the thickness of the countertop exceeds 20 mm, the excess of the back of the countertop should be beveled a plane.
3.4 In case the partition board is installed, or there is no air intake pert.
Make use of hole saw to create holes on the partition (see the picture
below)
Important Notice
Do not place any miscellaneous objects at the bottom of the appliance for
sufficient ventilation.
Installation Location
(Unit: an)
Distance from the wall (If the surrounding wall Is a combustible/nonfire
protection construction wall)
* Note: Example in the blanket equipped with flameproof construction or
heat insulation board will be discussed.
Installation of heat insulating board (Unit: cm)**
If the actual situation cannot fulfill the recommendation shown above, install
heat insulation board instead and follow the installation instruction shown
below.
Important Notice
Try not to let the metal parts of the appliance in contact with those
metals in the kitchen during installation.
If the metal part of the appliance is touching another metal material, keep
the material inside the wall (ie. metal lath) .
Electrical Work (Electrical work should be carried out by a qualified
electrician.
- The local wiring, earthing and safety regulations must be followed.
- The power supply shall be disconnected easily in case of emergency.
- To avoid stretching or twisting the power cord, beware of the power plug direction.
5.1 Installation of wall socket (Built-in)
- Install the power socket at a location where the plug can be taken off easily during normal usage.
5.2 Installation of wall socket (Freestanding)
- Install the power socket to a location away from hot air, water source and food-spattered areas.
Special Avowal
- This information above has been checked; our company reserves the hermeneutic power to any print errors or misunderstandings on the content.
- Please note that any technology improvement will be added to the new versions of the operation manual and installation instructions without any prior notice.
- In case there is any inconsistency or conflict between the English versions and Chinese versions of the terms, the Chinese versions shall prevail.
- The product appearance, color, specification, installation diagram and installation size etc. are subject to the actual appliance.
- E-copy of the installation manual can be sent by e-mail on request, please call Shun Hing Electric Works & Engineering Co, Ltd at 2861 2767.
SHUN HING ELECTRIC WORKS AND ENGINEERING CO., LTD.
2861 2767 2865 6706
http://www.rasonic.com
shew@shunhinggroup.com
Office: 9/F, Peninsula Centre, 67 Mody Road, Tsimshatsui East, Kowloon, Hong
Kong Tel: 2861 2767 Fax: 2865 6706
Website: http://www.rasonic.com
E-mail: shew@shunhinggroup.com
Maintenance and Repair Service: SHUN HING ELECTRIC SERVICE CENTRE LTD.
2406 5666 2408 0316 http://www.shesc.com/zh
11/F, Shun Hing Centre, 2 Shing Yiu Street, Kwai Chung, N.T. HK Service
Hotline: 2406 5666 Fax No.: 2408 0316
Website: http://www.shesc.com/en
Customer Service Centre
1/F, Shun Hing Centre, 2 Shing Yiu Street, Kwai Chung, N.T.
9/F., Block B, Peninsula Centre, 22/, Parkview Centre, 7 No. 193-199,5 andar
–
http://www.shesc.convey
For the latest information of Hong Kong and Macau service centers, please
visit
http://www.shesc.com/en
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>