Rasonic RIC-S28DN 2800W Single Burner Induction Cooker Instruction Manual

Rasonic RIC-S28DN 2800W Single Burner Induction Cooker

Safety Precautions for Installation

1. Check the following Accessories supplied,
   • A copy of operation manual and installation manual
   • A copy of warranty registration card
   • A bundle of adhesive tape
2. Do not disassemble the top plate during installation.
3. Do not install the appliance over a dishwasher, washing machine, dryer, electric oven or refrigerator.
4. Make sure to have a trail running test before installing the appliance. For built-in installation, leaving at least 100 mm space at both sides, front and back from the wall. Also, at least 150 mm apart from the bottom of the appliance and 80 cm2 should be reserved for air inlet/ exhaust space. For free-standing installation, leaving at least 100 mm space at both sides, front and back from the edge.
5. Follow the manual to install the appliance. If improperly installed, it may cause leakage of electricity or lead to overheat. Connect the power cord with the plug of the appliance to 13A socket. If fixed connection wiring is needed, disconnection must be incorporating an independent switch with 13A or above in accordance with the Electricity Ordinance.
6. If dedicated circuit wiring is not connected compatibly, it may lead to abnormal raise of wiring temperature.
7. Electrical work should be done by a qualified electrician. If the connection or repairing is finished improperly, it may cause electric leakage, malfunction or other hazards.
8. Never disassemble, repair or modify the appliance by yourself. Attempt to do so may cause malfunction or hazards.
9. Install the grounding completely with related ordinance. Installation of grounding can avoid electric shock once electric leakage occurs.
10. Grounding installation should be installed by a qualified electrician, avoiding electric shock during electrical leakage.
11. If the power cord is damaged, it must be replaced by Shun Hing Electric Service Centre Ltd. as to avoid hazard.
12. Do not step on or drop any objects on the top plate. If it is cracked or broken, it may cause overheat, malfunction or electric shock.
13. Use heat resistive materials for countertop where it should be the same or better than thermosetting high-pressure decorative materials. If the materials are not heat resistive, it may cause deformation or fire. Do not use varnished material as they may be discolored.

Product Installation Dimensions

(Unit: mm)

Dimensions with Tailor-made Kitchen Cabinet (Built-in)

1. Adhesive tape
   The attached adhesive tape is about 1.4 meters long. Cut off goo (Diagram 1) of the adhesive tape and
   fold it into an inner angle go0 (Diagram 2), remove the protection paper of the adhesive tape and adhere to the surrounding of the countertop. Remove the protection paper from the other side of the adhesive tape, then place the appliance on top of the countertop accurately and compress tightly.

   ---

   Note: Use the adhesive tape around the countertop, do not cut it apart; otherwise, it may affect the sealing performance.

2. Ensure the space of air intake to the cabinet and the space under the appliance are enough for sufficient ventilation. (Unit: mm)

Insert the backside of appliance into countertop, then fit the whole unit.

• Do not drop the appliance onto the countertop.
• Confirm the clearance distance between the bottom frame and the countertop are equal from front to back and from side to side.
• If power cord is trapped between the cabinet and the bottom/side of the appliance, the uneven gap may cause vibration.
• If there is a bulge on the countertop (Diagram 1), do not install the appliance on top of it.
• Place the appliance horizontally into the countertop opening and make sure the appliance is installed evenly and stable (Diagram 2).

If the thickness of the countertop exceeds 20 mm, the excessive part of the back countertop should be beveled with a plane. (Unit: mm)

4. In case a partition board is installed, or there is no air intake.
   Make use of holesaw to drill holes on the partition (see the picture below)

Important Notice
Do not place any miscellaneous objects under the appliance to ensure sufficient ventilation.

Installation Location

(Unit: cm)

Distance from the wall (If surrounding wall is combustible/non fire protection construction wall)

* Note:** Content in the blanket below is only suitable if the location equipped with flameproof construction or heat insulation board.

Installation of heat insulating board (Unit: cm)
If the actual situation cannot fulfill the recommendation shown above, it is suggested to install a heat insulation board follow the instruction below to install.

Important Notice
Do not allow metal parts of the appliance encounter with metallic parts in the kitchen during installation.
If the metal part of the appliance encounter another metal materials, keep the materials inside the wall (i.e. metal lath).

Electrical Work (Should be carried out by qualified electrician.)

• The local wiring, earthing and safety regulations must be followed.
• Electricity supply shall be disconnected easily in case of emergency.
• To avoid stretching or twisting the power cord, beware the direction of the power plug.

1. Connection to the wall socket (built-in)
   • Install the power socket at a location where the plug can be easily taken off during normal usage.
2. Connection to the wall socket (Free- standing)
3. Install the power socket to a location away from hot air, water source and food-spattering.

Special Avowal

1. This information above has been checked; our company reserves the hermeneutic power to any print errors or misunderstanding on the content.
2. Please note that any technology improvement will be added to the new versions of operation manual and installation instruction without any prior notices. The product appearance, color, specification, installation diagram and installation dimensions etc. are subject to the actual appliance.
3. In case there is any inconsistency or conflict between the English versions and Chinese versions of the terms, the Chinese versions shall prevail.
4. E-copy installation manual can be sent by e-mail on request, please call Shun Hing Electric Works & Engineering Co., Ltd. at 2861 2767.

Office: 9/F, Peninsula Centre, 67 Mody Road, Tsimshatsui East, Kowloon, Hong Kong
Tel: 2861 2767
Fax: 2865 6706
Website: http://www.rasonic.com
E-mail: shew@shunhinggroup.com

Customer Service Centre
1/F, Shun Hing Centre, 2 Shing Yiu Street, Kwai Chung, N.T.
9/F., Block B, Peninsula Centre, 67 Mody Road, Tsim Sha Tsui East, Kowloon
22/F, Parkview Centre, 7 Lau Li Street, Tin Hau, Hong Kong

For the latest information of Hong Kong and Macau service center, please visit http://www.shesc.com/en

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>