vtech W960 E-Smart Wireless Thermostat User Manual
- June 4, 2024
- vtech
Table of Contents
W960 E-Smart Wireless Thermostat
Controller Operation
FCC Caution:
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
IMPORTANT NOTE:
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance 20cm between the radiator& your body.
ISEDC Warning
This device complies with the Innovation, Science, and Economic Development
Canada licence-exempt RSS standard(s). Operation is subject to the following
two conditions: (1) this device may not cause interference, and (2) this
device must accept any interference, including interference that may cause
undesired operation of the device.
The device is compliant with RF exposure guidelines, users can obtain Canadian
information on RF exposure and compliance. The minimum distance from the body
to use the device is 20cm.
Thermostat Operation
Turn On the Screen
Touch any key on the screen (e.g. ) to turn on the screen.
Confirm Selected Option
Press button.
Fan Setting
Press the button to enter the fan setting. To select different fan speeds, you
may press the button multiple times to cycle through fan speeds or you may
press the button to change.
Temperature Setting
Press to adjust the set temperature.
Press to confirm or 5s timeout.
A tick wil show on the screen if the option has been selected.
Main Menu (MODE, FAN, TEMP.UNIT)
Press and hold for 3 seconds on the home screen to go to the main menu.
The options of the main menu are Mode, Fan, and TEMP.UNIT:
Press
to select different options.
Press to confirm the selected option to enter its sub-menu.
Press to confirm the option that has been selected in the sub-menu. If you
confirmed the option, the thermostat will show a tick . Press any key or wait
for 2 seconds, and the screen will go back to the home screen.
Restore Profile Setting
Press and hold and button for 10 seconds. The prompt will appear on the
thermostat.
Press any key or 3 seconds timeout, then the thermostat will be reset to the
profile setting you have configured with the EC Tool.
Override Temperature Setpoint
Press and hold Key for 3s after release button when reach to maximum or
minimum heating/cooling/auto setpoint.
Low Battery Alert Indicator
When the AAA battery power is low, the Low Battery Alert LED indicator
turns on and flashes red slowly on the remaining two months of its battery
life with 24 months.
When the AAA battery power is extremely low, the Low Battery Alert LED
indicator flashes red fast on the remaining 2 days of its battery life with 24
months. The display of the thermostat will be turned off.
If no battery LED displays, the thermostat is in normal operation.
Engineering Mode
Press and hold for 1 Os to access the engineering mode. The menu options of
engineering mode are as below:
Press to select different options.
Press to confirm the selected option.
Tour
It is the demo for you to try out and have fun.
Controller Operation
Pair the Controller with the Thermostat
Hold the [PAIR] button on your controller for 5 seconds (but less than 10
seconds), then release the button to start searching an available thermostat.
Stop Pairing the Controller with the Thermostat
Hold the [PAIR] button for 10 seconds and release it to start unpairing.
Controller LED Indicator
| Dual Color LED | Condition | Annotation |
|---|---|---|
| Flash green | Start Zigbee pairing | Press and hold [PAIR] for 5s (less than |
10s), and the controller indicator will turn to flash green, and when you
release the button, will enter Zigbee pairing mode.
During the process of Start Zigbee pairing (with the controller Indictor is
flash green), if the user wants to stop the pairing process, can press and
hold [PAIR] for 5s.
Solid green| Paired. Normal operation. The Controller is connected to the
thermostat operating normally.| /
Flash yellow| Removing all devices from system/ Factory reset.| When there is
a paired device, press and hold Los [PAIR] to remove all connected devices.
Solid yellow| Not paired| Situation 1: When it Is powering up
Situation2 If the controller is not paired with the thermostat
Flash green & red
alternatively| Disconnected. The Controller is searching and trying to
reconnect to the thermostat| After disconnecting the thermostat, the
controller keeps searching for the thermostat
Solid red| Error| Any problems cause the HVAC or Controller not to work
Specifications are subject to change without notice.
Copyright © 2022
VTech Communications, Inc.
All rights reserved. 8/18.
W960_Operation_QSG_V3 _2022.08.18