2E G3022B LCD Monitor User Manual

: June 13, 2024
: 2E

Table of Contents

Warnings/Safety precautions
Important safety instructions
Operating Instructions
- Components and auxiliary equipment
Installation
- Installation of base
- Installation of mount
Functions
- Description of buttons
Explanation of indicators
Description of connection socket
OSD menu
- Menu description
Specifications
Troubleshooting
Additional information
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

2E G3022B LCD Monitor

2E G3022B LCD Monitor

Warnings/Safety precautions

Symbol

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER AND BACK PANEL THERE ARE NO USER-SERVICEABLE PARTS INSIDE.
I CASE OF DAMAGE OR ERROR REFER SERVICING TO QUALIFIED PERSONNEL

Lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of non-insulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock in case of improper usage of the product.

Exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance instructions in the literature accompanying the product.

WARNING:

Do not put the monitor in rainy or foggy places to prevent from fire or electric shock.
To prevent scratches or damages to the LCD screen, do not knock, apply or rub the surface with sharp or hard objects or stiff cloths as well as try not to touch the LCD screen with your hands.

Any modifications to this product that have not been clearly and explicitly approved in advance by the manufacturer responsible for compliance with these regulations are forbidden.

ATTENTION:

Excessive sound pressure from earphones and headphones can cause hearing loss.

Important safety instructions

Please read all the instructions carefully before using this product.
The instructions should be retained after reading for future reference.
Please immediately pull out the AC power plug from an adapter if there is an abnormal sound or smell or the monitor has no picture, and contact after sales support.
The monitor should be kept free from rain, damp and dust to prevent electrical shock and short circuits. Do not cover the ventilation openings with table clothes, curtains, newspapers etc.
The monitor should be kept away from heating objects or direct sunlight. This product requires good ventilation. Allow 10 cm between the monitor and other appliances or built-in cabinet walls.
You may clean the display panel with a soft clean cloth after pulling out the power plug. Do not repeatedly wipe the panel, nor scrape, tap or strike the panel with hard objects, etc.
Do not wipe the monitor with any petrol chemical or alcohol-based solvents, as it will lead to product damage to the panel and cabinet.
Do not place the monitor on an unstable surface.
Do not place the power cord or other cables across a walkway in case it is trampled on, especially at the points of connection to the plug, sockets and the power cord to the appliance.
Unplug the appliance during a lightning storm or when it is not used for a long period of time.
Unplug this product when the device, power cord or plug are damaged or if the device has been exposed to liquid or moisture, has been mechanically damaged and does not work properly and contact an authorized service centre immediately.
Keep this appliance away from liquids, splashes of water and do not place objects filled with liquids on it.
Do not disassemble the back cover as it contains high voltages inside and will cause electric shock.
There is no spare parts inside. Internal adjustments and checks should only be conducted by qualified professionals.
Do not place naked flame sources, such as lit candles on or near the monitor. Please pull out the power plug and contact after sales support if there are abnormal objects or water in the monitor.

Operating Instructions

Components and auxiliary equipment

Before assembling and installing, check for following items to be included in this display package.
Operating Instructions

Note: The redundant screws are used as spare screws.

Installation

Installation of base

Open the carton package, take out the foam and put it flat on the table top. Keep the foam underneath the monitor before attaching the stand.
Take out the support and rotating shaft assembly and lock it with two screws.
Lock the bracket and base with a screw
Put the assembled base into the corresponding slot of the back shell, gently press the bracket to lock it into the lock, then hold the middle of the bracket, gently lift the body twice, do not loosen, make sure it can be locked.

Note: In order to prevent the monitor from falling when it is used on the wall, please install it properly and do safety protection. Do not place or hang any objects on the wall bracket, and the wall height should be within 2 meters.

Installation of mount

Open the carton package, take out the foam and put it flat on the table top. Keep the foam underneath the monitor before attaching the stand.
Take out the wall mount assembly and lock the wall mount assembly with mount hexagon irons.
Note: Hang the assembled product on a hard wall. Do not pinch the screen with your hands during the hanging process to avoid damaging the screen.

Functions

Description of buttons

Functions

Button	Function
1	Power button: Turn on/off the monitor
2	Exit/Left button: Exit or return
3	Down button: Move down in the menu
4	Menu button: Enter sub-menus
5	Up button: Move up in the menu

Explanation of indicators

Explanation of indicators
Indicator: Steady blue light indicates the power is on and the monitor runs normally. Red light indicates no video source and no horizontal or vertical signal detected or low voltage.
Please make sure that your computer is turned on and all video cables are fully plugged in and/or connected.

Description of connection socket

The bottom interface configuration at the back of the monitor varies with products.
Note: If the power cable or signal cable is damaged, you must replace it with special soft cables or special components purchased from the customer care officer.

HDMI interface

Use the HDMI-DVI cable to connect the HDMI IN interface of the product to the DVI OUT interface of a PC.

(In general, PCs do not transfer video signals to the monitor through the DVI OUT interface , and it is necessary to connect a loudspeaker box additionally to play sounds of PCs.)

DP interface

Use the DP cable to connect the DP IN interface of the product to the DP OUT interface of a PC.

AUDIO OUT

Connect audio output devices such as earphones to the AUDIO OUT interface.

DC interface

Please connect the power adapter to the power cable, connect the power adapter plug to the corresponding power port of the monitor, and then connect the power cable to a properly grounded power outlet.

The color and shape of the OSD menu of the actual computer may be slightly different from them shown in the figure.
Specifications of the OSD menu may change with improvements of functions without prior notice

Press the menu button on the control panel to access the monitor menu. The detailed information of each menu can be found in the following sections.

Rocker key (Right) to enter the OSD main menu or enter sub-menus
Rocker key (Up) to pattern of situations or move up in the menu.
Rocker key (Down) to enter the «GamePlus» or move down in the menu.
Rocker key (Left) to enter the Input Signal or exit the current screen.

Level1	Level2	Level3

Game Settings

Game Time

| On/Off:15:00/30:00/45:00/60:00:Top Right/ Top Left/Bottom Right/ Bottom Left
Dynamic Brightness| Off/Normal/Expert/Elaboration
MPRT| On / Off
Ambient Lighting| On / Off

Picture Quality Settings

| Brightness| (Adjustment Bar; Range: 0 – 100) Default 80
Contrast| (Adjustment Bar; Range: 0 – 100) Default 50
DCR| On/Off
Contextual Model| Off/On: Movie Mode/Reading Mode/Night Mode/Care Eyes Mode
Sharpness| (Adjustment Bar; Range: 0 – 100) Default 0
Low Blue Light| (Adjustment Bar; Range: 0 – 100) Default 0
Gamma| 1.8 / 2.0 / 2.2 / 2.4 / 2.6 / Secure
Aspect Ratio| Wide Screen / 4:3 / 1:1 / Auto
Color Settings| Warm / Natural / Cool User1/User2/User3 Hue/Saturation PIP/PBP Mode
Sub-Signal Source Audio Source
PIP Position PIP Size
Swap
Language OSD Time Out
OSD H-Position OSD V-Position OSD Transparency Hotkey1 Setting Hotkey2 Setting Hotkey3 Setting OSD RotationOSD Lock| On / Off
Off/On: Red, Green, Blue (Adjustment Bar; Range: 0 – 100) Default 50
Red, Green, Blue(Adjustment Bar; Range: 0 – 100) Default 50
PIP/PBP| O/PIP Mode/PBP 2Win 1:1
DP/HDMI1/HDMI2
Auto/DP/HDMI1/HDMI2
Top Right / Top Left / Bottom Right / Bottom Left
Small / Medium / Large
—
OSD Settings| English / УКРАЇНСЬКА / РУССКИЙ…..
(Adjustment Bar; Range: 0 – 100) Default 20
(Adjustment Bar; Range: 0 – 100) Default 50
(Adjustment Bar; Range: 0 – 100) Default 50
(Adjustment Bar; Range: 0 – 100) Default 0
Brightness/Contrast/Volume/Mute/Shadow Balance/Game Crosshair/Refresh Rate/Game Time/Contextual Model/ PIP/PBP Mode/Input Signal/Dynamic Brightness
Normal / 90 / 180 / 270
On/Off
Other Settings| Input Source
Volume
Mute
Auto Power
Eye shield Remind
Reset| Auto/DP/HDMI1/HDMI2
(Adjustment Bar; Range: 0 – 100) Default 50
On/Of
On/Of
On/Of
Yes/No
Input Source:HDMI2 Resolution:2560×1080@60Hz Mode: Movie Mode SN:

Specifications

Model	G3022B
Screen size	30’’ Curve (1500)
Matrix type	VA
Aspect ratio	21:9
Viewing angles	178 °/ 178 °
Displayable colours	16.7M (8-bit)
Resolution	2560×1080
FPS	100 Hz
Response time	1ms MPRT
Brightness	250 cd/m2
Contrast	3000:1
Interfaces	2xHDMI 2.1, DP 1.4, Audio out
Built-in speakers	No
Screen tilt	-5°~+20°
Height adjustment	No
Screen rotation	No
Monitor Power Options	48W, 12V, 4.0A
External power adapter parameters	100-240 V, 50/60 Hz, 4.0 A
Power consumption in operating mode (max)	<55W
Standby power consumption	≤0.5W
Wall mounting	VESA 75×75
Package dimensions	794x172x405 mm
Weight (NET/GROSS):	5.2 kg/7.3 kg

Troubleshooting

Problem	Solution

Power cannot be turned on

|

Check that both ends of the power cable are plugged into the socket appropriately and the wall socket is operational

No Input signal message|

Check that the signal line is connected properly.
Check that the power of the relevant peripherals is turned on.
Check that the Input option tnat has been selected matches with the input signal.

Image colour or quality deteriarates|