2E GAMING G3422B LCD Monitor Instruction Manual
- June 2, 2024
- 2E GAMING
Table of Contents
2E GAMING G3422B LCD Monitor Instruction Manual
WARNINGS/SAFETY PRECAUTIONS
WARNINGS/SAFETY PRECAUTIONS
RISK OF ELECTRIC SHOCK DO NOT OPEN
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER AND BACK PANEL THERE ARE NO USER-SERVICEABLE PARTS INSIDE. I CASE OF DAMAGE OR ERROR REFER SERVICING TO QUALIFIED PERSONNEL.
Lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of non-insulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock in case of improper usage of the product.
Exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance instructions in the literature accompanying the product.
WARNING:
Do not put the monitor in rainy or foggy places to prevent from fire or
electric shock. To prevent scratches or damages to the LCD screen, do not
knock, apply or rub the surface with sharp or hard objects or stiff cloths as
well as try not to touch the LCD screen with your hands.
Any modifications to this product that have not been clearly and explicitly approved in advance by the manufacturer responsible for compliance with these regulations are forbidden.
ATTENTION:
Excessive sound pressure from earphones and headphones can cause hearing loss.
Important safety instructions
-
Please read all the instructions carefully before using this product.
-
The instructions should be retained after reading for future reference.
-
Please immediately pull out the AC power plug from an adapter if there is an abnormal sound or
smell or the monitor has no picture, and contact after sales support. -
The monitor should be kept free from rain, damp and dust to prevent electrical shock and short
circuits. Do not cover the ventilation openings with table clothes, curtains, newspapers etc. -
The monitor should be kept away from heating objects or direct sunlight. This product requires
good ventilation. Allow 10 cm between the monitor and other appliances or built-in cabinet walls. -
You may clean the display panel with a soft clean cloth after pulling out the power plug. Do not
repeatedly wipe the panel, nor scrape, tap or strike the panel with hard objects, etc. -
Do not wipe the monitor with any petrol chemical or alcohol-based solvents, as it will lead to
product damage to the panel and cabinet. -
Do not place the monitor on an unstable surface.
-
Do not place the power cord or other cables across a walkway in case it is trampled on, especially at the points of connection to the plug, sockets and the power cord to the appliance.
-
Unplug the appliance during a lightning storm or when it is not used for a long period of time.
-
Unplug this product when the device, power cord or plug are damaged or if the device has been
exposed to liquid or moisture, has been mechanically damaged and does not work properly and contact an authorized service centre immediately. -
Keep this appliance away from liquids, splashes of water and do not place objects filled with liquids on it.
-
Do not disassemble the back cover as it contains high voltages inside and will cause electric shock. There is no spare parts inside. Internal adjustments and checks should only be conducted by
qualified professionals. -
Do not place naked flame sources, such as lit candles on or near the monitor. Please pull out the power plug and contact after sales support if there are abnormal objects or water in the monitor.
Operating Instructions
Components and auxiliary equipment
Before assembling and installing, check for following items to be included in
this display package.
Monitor x 1| Stand stem x 1| Base x 1
---|---|---
Power adapter x 1| Screws x 3| Mount hexagon irons x 4
DP signal cable x 1| User manual x 1| Microfiche and power
requirements label
Redundant screws can be used as spare screws.
Installation
-
Open the package and take out the product with the foam still attached. Gently place it on a desktop or table.
-
Remove the polyfoam and the inner package bag, place on a desktop or table, keep the lower foam underneath the monitor.
-
See picture, fasten the stand stem and base with a screw.
-
Press the button to remove the stand plate, Fix the stand plate into the stand stem with the supplied screws.
-
Fix the whole assembled stand into the monitor, and check carefully to make sure it is fastened.
-
Hold onto the stand stem and stand the monitor up on a flat, level desktop or table. Due to the heavy weight and dimensions of the LCD screens and their fragile nature, we recommend that they are unpacked and assembled by 2 people. The stand can be removed from the rear of the monitor by pressing the quick release button on the rear of the monitor.
Installation
-
Open the package and take out the product with foam still attached Gently place it on a desktop or table. Remove the parts and the foam covering the monitor. If the monitor is already attached to the stand, remove the stand.
-
Press the button to remove the adapter on back of monitor, then tighten the included four screws onto the mounting holes on back of monitor.
-
Install the monitor on the wall, mount, or fixture as desire.
-
During padlocking of the monitor, do not pinch the screen with the hands to avoid damaging the screen. Install the mount to the mount stud by referring to the user manual of the mount (purchased separately
Tips: The mounting hole distance of the mount for the product is 75x75mm. Do
not place or hang any object on the mount, and the using height of the mount
should be less than 2 meters.
Notes: To prevent the monitor on the mount from failing, please install it
firmly and protect it fully.
Do not place or hang any object on the mount, and the using height of the mount should be less than 2 meters
Functions
Description of connection sockets
- **HDMI interface
** Use the HDMI cable to connect the HDMI IN interface of the product to the HDMI OUT interface of a PC.
Use the HDMI-DVI cable to connect the HDMI IN interface of the product to the DVI OUT interface of a PC. (In general, PCs do not transfer video signals to the monitor through the DVI OUT interface, and it is necessary to connect a loudspeaker box additionally to play sounds of PCs.)
-
DP interface
Use the DP cable to connect the DP IN interfaceof the product to the DP OUT interface of a PC, -
AUDIO OUT
Connect audio output devices such as earphonesto the AUDIO OUT interface.. -
AC interface
Please connect the power cable plug to the corresponding port of the monitor, and connect the other end to a properly grounded power outlet.
Power indicator
_ Description of buttons
_ Indicator: A steady blue light indicates that the power is on and the
monitor is operating normally. Blue light flashing to indicate There is no
video source and no horizontal or vertical signal or low voltage is detected.
Make sure your computer It is turned on and all video cables are fully plugged
in and/or connected.
Button | Function |
---|---|
Menu: Press to display OSD menu and enter sub-menus | |
Down: Press to move down in menus | |
Up: Press to move up in menus | |
Exit: Press to exit OSD menu | |
Power: Press to turn monitor on/off |
OSD menu
Menu description
- The color and shape of the OSD menu of the actual computer may be slightly different from them shown in the figure.
- Specifications of the OSD menu may change with improvements of functions without prior notice.
The screen display (OSD) menu can be used to adjust settings of the monitor
and is shown on the screen after the monitor is powered on and the used t e
(Home) button is pressed. (H 1. Press one of the buttons ( ) ) to activate the
browser screen.
. Press ( used t e ) to enter the OSD screen.
Press or to scrollthrough the functions.
- Select the desired function, and press used t e to enter the sub-menu. (H
- Press or to scroll through sub-menus, and press used t e key to select and confirm the ( desired function.
- Pres or to select one option, and press used t he to confirm settings and exit from the ( current menu.
Press ss to exit from the menu screen.
Functions OSD menu
Level1 | Level2 | Level3 |
---|---|---|
**** Input Source | DP1(1.4) | — |
DP2(1.4) | — | |
HDMI1(2.0) | — | |
HDMI2(2.0) | — | |
**** Brightness/Contrast | Brightness | (Adjustment Bar; Range: 0 – 100) |
Default 80
Contrast/Blacklevel| (Adjustment Bar; Range: 0 – 100) Default 50
DCR| On / Off
**** Color Setting| Gamma| 1.8 / 2.0 / 2.2 / 2.4 / 2.6
Pictrue Mode| Standard / Photo / Movie / Game / FPS / RTS
Color Temperature| Warm / Cool / USER
Low Blue Light| (Adjustment Bar; Range: 0 – 100) Default 0
Hue| Hue (Adjustment Bar; Range: 0 – 100) Default 50
Saturation| Saturation (Adjustment Bar; Range: 0 – 100) Default 50
**** Picture Quality Setting| Sharpness| (Adjustment Bar; Range: 0 –
100) Default 50
Response Time| Off / High / Middle / Low
Noise Reduction| Off / High / Middle / Low
Super Resoultion| Off / High / Middle / Low
Dynamic Luminous Control/MPRT| On / Off
Display| Aspect Ratio| Wide Screen / 4:3 / 1:1 / Auto
LedMode| Normal / Off / Flicker
| Mute| On / Off
Audio| Volume| (Adjustment Bar; Range: 0 – 100) Default 50
| Audio Source| HDMI1(2.0) / HDMI2(2.0) / DP1(1.4) / DP1(1.4)
| Multi-Window| Off / PIP Mode / PBP 2Win
| Sub Win2 Input| DP1(1.4) / DP2(1.4) / HDMI1(2.0) / HDMI2(2.0)
Multi-Window| PIP Size| Small / Medium / Large
| PIP Position| TopRight / TopLeft / BottomRight / BottomLeft
| Swap| —
| Language| English / УКРАЇНСЬКА / РУССКИЙ…..
| OSD H-Position| (Adjustment Bar; Range: 0 – 100) Default 50
** OSD| OSD V-PositionOSD Transparency| (Adjustment Bar; Range: 0 – 100)
Default 50
(Adjustment Bar; Range: 0 – 100) Default 20
| OSD Time Out| (Adjustment Bar; Range: 0 – 100) Default 20
| OSD Rotation| Normal / 90 / 180 / 270
| DP Version| DP1.1 / DP1.2/ DP1.4
** Other| FreeSync(Adaptive Sync)HDR| On / Off
On / Off/ Auto
| Reset| —
Specifications
Model | G3422B |
---|---|
Screen size | 34’’ Curve (R1500) |
Matrix type | VA |
Aspect ratio | 21:9 |
Viewing angles | 178 °/ 178 ° |
Displayable colours | 16.7M (8-bit) |
Resolution | 3440×1440 |
FPS | 165 Hz |
Response time | 1ms MPRT |
Brightness | 350 cd/m2 |
Contrast | 3000:1 |
Interfaces | 2xHDMI (2.0), 2xDP (1.4), Audio out |
Built-in speakers | Yes |
Screen tilt | -5°~+15° |
Height adjustment | 100mm |
Screen rotation | 15°(± 2°) |
HDR support | HDR400 |
External power adapter parameters | 100-240 V, 50/60 Hz, 2.0 A |
Power consumption in operating mode (max) | <80W |
Standby power consumption | ≤0.5W |
Wall mounting | 75х75 |
Package dimensions | 907x182x486 mm |
Weight (NET/GROSS): | 7.72 kg/10.32 kg |
Sync technology | Adaptive-Sync |
**** Additional Information | Low Blue Light |
Flicker Free
Troubleshooting
Problem | Solution |
---|---|
**** Power cannot be turned on | Check that both ends of the power cable are |
plugged into the socket appropriately and the wall socket is operational
**** No Input signal message| Check that the signal line is connected
properly.Check that the power of the relevant peripherals is turned on.Check
that the Input option tnat has been selected matches with the input signal.
Image colour or quality deteriarates| Check that all the video settings are
adjusted appropriately, such as brightnešs, contrast, colour etc.
**** Display warning message| Check that the input signal line is properly
fixed. Select the correct input signal source
Additional information
The production date is encrypted in the serial number in the format ERC2E *
YYYYMMDD *****, where: YYYYMMDD – year, month and day of production.
References
- Головна - 2E GAMING
- ÐšÐ¾Ð¼Ð¿Ð°Ð½Ð¸Ñ ERC: СервиÑ-центр(СЕРВІСÐИЙ ЦЕÐТР)
- Yurd.az
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>