Cimarron LS10-110 110 Gallon 5.5 HP Skid Sprayer Owner’s Manual

June 13, 2024
Cimarron

Cimarron LS10-110 110 Gallon 5.5 HP Skid Sprayer

General Information

Thank you for purchasing this product. The purpose of this manual is to assist you in operating and maintaining your skid sprayer. Please read it carefully, as it furnishes information which will help you achieve years of trouble-free operation.

Warranty/Parts/Service

Products are warranted for one year from date of purchase against manufacturer or workmanship defects.
Commercial users have a 90 day warranty.

Technical Specifications

  • 110 Gallon Polyethylene Tank
  • 5.5 HP Recoil Start Engine w/Gear Reduction
  • 8-Roller Cast Iron Pump
  • 10 g.p.m. @ 250 PSI
  • Pressure Gauge – Adjustable Pressure Range
  • Suction Line Filter
  • Handgun w/25 Feet of Hose
  • Tank Drain Feature
  • (Optional) Trailer Kit Available

Operation

Roller pumps are positive displacement pumps which means that the entire solution being pumped must go somewhere or the pump will break. In this roller pumping system, solution is drawn from the tank and forced to a planned source such as a handgun. The pressure is controlled by a relief valve which is a spring loaded device that controls the amount of fluid bypassed to the tank. The handle is to be tightened to increase pressure and loosened to decrease the pressure. The suction line strainer should be checked periodically and cleaned. Stop the engine and shut off the valve near the strainer. Remove the bowl and screen portions of the strainer and wash them free from all impurities. You may also drain the tank by uncoupling the suction line near the strainer. Open the valve and pour the contents into another container. Read the chemical label for disposal instructions.

NOTICE: The engine does not have any oil in the crankcase. See the engine manual for type and amount. Always check the oil in the gear box. Remove the plug on the side, oil should be visible. Add oil through the top plug.

Testing the Sprayer

NOTE:
It is VERY important for you to test your sprayer with plain water before actual spraying is attempted. This will enable you to check the sprayer for leaks, without the possibility of losing any expensive chemicals.

Read the operating instructions.

  1. Open tank lid and be sure the tank is clean and free of foreign material. Fill the tank about half full with plain water.

  2. Open the valve at the strainer inlet and allow water to flow to the pump. The valve is located at this point to enable the strainer to be taken apart for cleaning.
    CAUTION: Always be sure that water has reached the roller pump before starting your sprayer. If the pump is run dry, serious damage to your pump will result.

  3. It is best to start the sprayer at little or no pressure. This sprayer is equipped with a spring loaded relief valve. Turn the valve handle out to decrease pressure, and in for increased pressure.

  4. You may now start the sprayer engine following the engine manufacturer’s instructions. Let the sprayer run at low pressure until water has reached the handgun, and all air has been purged from the handgun line.
    CAUTION: Care must be taken, being sure the handgun is secured in the operator’s hand. If this is NOT done, a recoiling action may occur causing damage or personal injury.

  5. The pressure should now be increased to 30-40 psi.
    Operate the sprayer at this increased pressure for 3 to 5 minutes, thoroughly testing the unit before adding chemicals.

When everything tests all right (no leaks, & good pressure), add the desired chemicals to the mixture and water combination and start your spraying operation. Adjust the pressure and spray as you did in the testing procedure. The sprayer should now be ready for use.

Conditions of weather and terrain must be considered when setting the sprayer. Do not spray on windy days. Protective clothing must be worn in some cases.

Be sure to read the chemical label(s) correctly!

After Spraying

After use, fill the sprayer tank part way with water. Start the sprayer, and allow the clear water to be pumped through the plumbing system and out through the spray nozzles. Refill the tank about half full with plain water and use FIMCO Tank Neutralizer and Cleaner, and repeat cleaning instructions above. Flush the entire sprayer with the neutralizing/cleaning agent, then flush out one more time with plain water. Follow the chemical manufacturer’s disposal instructions of all wash or rinsing water. For the boom, (if applicable) remove the tips and screens from the nozzle assemblies. Wash these items out thoroughly. Blow the orifice clean and dry. If the orifice remains clogged, clean it with a fine bristle (NOT WIRE) brush, or with a toothpick. Do not damage the orifice. Water rinse and dry the tips before storing.

WARNING: Some chemicals will damage the pump valves if allowed to soak untreated for a length of time! ALWAYS flush the pump as instructed after each use.

Winter Storage

Drain all water out of your sprayer, paying special attention to the pump, handgun, and valve(s). These items are especially prone to damage from chemicals and freezing weather.

The sprayer should be winterized before storage by pumping a solution of RV antifreeze through the entire plumbing system. This antifreeze solution should remain in the plumbing system during the winter months. When spring time comes and you are preparing your sprayer for the spray season, rinse the entire plumbing system out, clearing the lines of the antifreeze solution. Proper care and maintenance will prolong the life of your sprayer.

Cast Iron 8-Roller, Reverse Rotation Pump Assembly

#5271509 (Hypro Part #7560C-R-01)

  • = Parts Available ONLY in Repair Kit #7771794 (3430-0381)

Item No| Part Number| Mfg. Part Number| Qty| Description
---|---|---|---|---
1| 1610-0059| 1610-0059| 1| Key (Stainless Steel)
2| 5002174| 0104-7500C| 1| Body (Cast Iron w/Seal)
3| 5017175| 0204-7500C| 1| End Plate (Cast Iron)
4| 5017522| 2300-0022| 1| Bearing Cover
5| 5017523| 2300-0020| 1| Shaft Bearing Cover
6| 5031044| 2008-0001| 2| Sealed Ball Bearing
7| 5034038| 2210-0004| 6| H.H.C.S. 5/16″-18nc x 3/4″ Long
8| 5072059| 1720-0014| 1| O-Ring Gasket
9| 5089012| 1610-0005| 1| Key
10| 5110058| 2112-0003| 2| Viton Seal (Standard)
*11| 5112030| 1005-0004| 8| Super Roller (Standard)
12| 5172113| 0308-7560C| 1| Rotor Assembly (7500C)

Performance Data For Pump No: 5271509 (7560C-R-01)

Pump Speed (RPM)

| 0 PSI| 50 PSI| 100 PSI| 150 PSI| 200 PSI| 250 PSI| 300 PSI
---|---|---|---|---|---|---|---

GPM

| HP| GPM| HP| GPM| HP| GPM| HP| GPM| HP| GPM| HP| GPM| HP
600| 14.0| .45| 13.1| .87| 12.1| 1.41| 11.2| 1.98| 10.6| 2.5| 10.0| 3.1| 9.1|

3.7

Exploded View/Parts List:

Gun Jet Spray Gun #5163005

(Spraying Systems Part No: AA43H-AL6)

Item No. Part Number Qty Description
1 ** 1 Gasket, Nylon
2 ** 1 Seat Plug, Seat Plate, Washer, & Core Sub-Assembly
3 ** 1 Packing Washer, Type 302 Stainless Steel
4 ** 3 Packing, Leather
5 5002203 1 Inlet Body, Aluminum
6 5002205 1 Handle Body, Aluminum
7 5006072 1 Stop Adjustment Nut, Steel – Zinc Plated
8 5006118 1 Locknut, Steel – Zinc-Plated
9 5006244 1 Stem Nut, Steel – Nickel Plated
10 5009080 1 Tubing, Aluminum
11 5016061 1 Washer, Stainless Steel
12 5016071 1 Spring Guide Washer, Type 302 Stainless Steel
13 5019069 1 Spring for Stop Adjustment Nut, Stainless Steel
14 5019083 1 Trigger Stop Spring, Stainless Steel
15 5019107 1 Main Spring, Stainless Steel
16 5046033 1 Cap, Aluminum
17 5063071 1 Orifice Disc, Stainless Steel
18 5072171 2 Gasket, Nylon
19 5076011 1 Trigger Guard, Steel – Nickel Plated
20 5077015 1 Guide Vane, Nylon
21 5084016 1 Nozzle Housing, Aluminum
22 5111017 2 Rivet, Steel – Zinc Plated
23 5117070 1 Spring Screw, Steel – Zinc Plated
24 5117143 1 Screw, Stainless Steel
25 5117165 1 Packing Screw, Aluminum
26 5131012 1 Trigger Stop, Steel – Nickel Plated
27 5132039 1 Stem, Type 416 Stainless Steel
28 5134010 1 Spring Stud, Stainless Steel
29 5166017 1 Trigger Guide, Steel – Nickel Plated
30 5166026 1 Trigger, Steel – Nickel Plated

** = Available in Spare Parts Kit (ONLY): #5168190 (PK-AB43-AL-KIT)

PISTON TYPE PRESSURE RELIEF/REGULATING VALVES

Bypasses excess liquid. Adjustable to maintain control of line pressure at any pressure within the valve operating range.
Selected pressure setting firmly held in place by locknut. Extra large passages to handle large flows.

  • Polypropylene with stainless steel spring
  • Excellent chemical resistance
  • EPDM O-Rings
  • For pressure to 150 p.s.i.
  • 1/4″ port for pressure gauge
  • Choice of 1/2″ or 3/4″ NPT (M) inlet & (F) outlet connections
FIMCO Number Mfg Part Number Description
5143199 23120-3/4-PP 3/4″ Poly Valve
5143200 23120-1/2-PP 1/2″ Poly Valve
5168717 PK-AB23120-KIT Repair Kit, Items Marked **

How to order: Specify valve number (Example: 23120-1/2-PP Polypropylene)

Item No| Part Number| Mfg Part Number| 5143199/Qty| 5143200/Qty| Description
---|---|---|---|---|---
1| 5046270| CP23122-NY| 1| 1| Adjusting Cap, Nylon (Gray)
2| 5108095| CP23124-PP| 1| 1| Spring Retainer
3| 5110266| CP23123-PP| 1| 1| Lock Ring
4| 5115078| CP23125-PP| 1| 1| Guide Seat
5| | F14| 1| 1| Pipe Plug, 1/4″ MNPT
6|
| CP23126-302SS| 1| 1| Retaining Pin
7| | CP23127-302SS| 1| 1| Spring
8|
| CP7717-15-EPR| 1| 1| O-Ring, EPDM Rubber
9| —| CP23121-PP| 1| –| Poly Body (3/4″ NPT)
10| —| CP23128-PP| –| 1| Poly Body (1/2″ NPT)

Parts List: LS10-110 (5301080)

Item No Part Number Qty Description
1 5006186 2 #10-24 Hex Whiz (Flange) Locknut
2 5006259 4 3/8-16nc Hex Flanged Whiz Nut Gr. 5
3 5006307 8 5/16-18nc Hex Flanged Whiz Nut Gr. 5
4 5006337 4 1/2-13nc Hex Flanged Whiz Nut Gr. 5
5 5010214 1 Poly Elbow, 1 1/4″ MNPT x 3/4″ HB (3EL11434)
6 5010251 1 Poly Coupler, 3/4″ FNPT
7 5011140 1 Poly Close Nipple, 3/4″ MNPT
8 5020099 1 Hose, 3/8″-2 Brd. x 25 Ft.
9 5020469 1 Hose, 3/4″-2 Brd. x 32″
10 5020472 1 Hose, 3/4″-2 Brd. x 17″
11 5020473 1 Hose, 3/4″-2 Brd. x 27″
12 5020473 1 Hose, 3/4″-2 Brd. x 27″
13 5020485 1 Hose, 3/4″-2 Brd. x 64″
14 5034018 4 H.H.C.S., 1/2″-13 x 1″
15 5034063 1 Round U-Bolt, 5/16″-18 x 1 3/16″ x 1 3/4″
16 5034069 4 H.H.C.S., 5/16″-18 x 1 1/2″ (Full Thread)
17 5034734 4 3/8″ x 6″ Hook Bolt
18 5038586 1 Valve Mount Bracket
19 5038638 1 Handgun & Hose Bracket
20 5051024 10 Hose Clamp, 3/4″
21 5051144 2 Hose Clamp, 3/8″
22 5067127 5 Poly Fitting, 3/4″ MNPT x 3/4″ HB
23 5067130 1 Poly Fitting, 1/2″ MNPT x 3/8″ HB
24 5075014 2 Rubber Grommet (Black)
25 5116213 1 Strainer
25.1 3351-0039 1 Strainer Bowl
25.2 5116131 1 Screen (40 Mesh)
25.3 5072299 1 EPDM Gasket
25.4 3351-0038 1 Strainer Cap
26 5117234 2 #10-24 x 1/2″ Phillips Truss Head Machine Screw
27 5117300 2 H.H.C.S. Flanged 5/16″-18nc x 1″ Long
28 5133224 1 Tank Strap (110 Gallon)
29 5133229 1 Tank Strap (110 Gallon) (Hose Hanger Strap)
30 5143123 1 Valve Celcon Globe, 3/4″
31 5163005 1 GunJet Spray Gun (AA43H-AL6)
32 5167034 1 Gauge, Liquid-Filled, 0-400# p.s.i.
.033 5169157 1 110 Gallon Tank (30″ Dia. x 44″ x 38″) (Yellow)
34 5274365 1 Skid Weldment (110 Gallon)
35 5274366 2 Saddle Weldment (110 Gallon)
36 5275145 1 Engine/Pump Sub-Assembly
37 5277602 1 Top Valve Assembly (LS10)
37.1 5011139 2 Poly Close Nipple, 1/2″ MNPT
37.2 5010230 2 Poly Tee, 1/2″ FNPT
37.3 5010243 3 Poly Street Elbow, (90 Deg) 1/2″ MNPT x 1/2″ FNPT
37.4 5143197 1 1/2″ T-800 Brass Ball Valve
37.5 5067133 2 Poly Fitting, 1/2″ MNPT x 3/4″ HB
37.6 5102070 1 Poly Pipe Plug, 1/2″ MNPT
37.7 5143200 1 Pressure Relief Valve (1/2″ NPT)
37.8 5067130 1 Poly Fitting, 1/2″ MNPT x 3/8″ HB
38 5277603 1 Tank Valve Assembly (LS10)
38.1 5010231 1 Poly Tee, 3/4″ FNPT
38.2 5011140 2 Poly Close Nipple, 3/4″ MNPT
38.3 5067127 2 Poly Fitting, 3/4″ MNPT x 3/4″ HB
38.4 5143206 1 3/4″ Single Union Ball Valve

Exploded View:
LS10-110 (5301080)

Engine/Pump Assembly #5275145

Item No Part Number Qty Description
1 5005177 1 Adapter & Kit (Coupler)
2 5006186 2 #10-24 Hex Whiz (Flange) Locknut
3 5016026 2 Lockwasher, 5/16″
4 5023052 1 Torque Bracket
5 5034634 2 5/16″-18 x 5/8″ Grd. 5 Flange Lock Screw (Serr.)
6 5040004 2 Rubber-Headed Machine Screw Bumper (#10-24)
7 5067127 1 Poly Fitting, 3/4″ MNPT x 3/4″ HB
8 5089003 1 1/4″ Square Keystock x 1 1/4″ Long
9 5089033 1 3/16″ Square Keystock x 1 3/8″ Long
10 5120044 1 Shield
11 5152099 1 5.5 H.P. Engine w/ Gear Reduction
12 5271509 1 8-Roller Cast Iron Pump (Reverse Rotation)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals