CIMARRON MC1 Series 3 Point Sprayers Owner’s Manual
- June 13, 2024
- Cimarron
Table of Contents
- MC1 Series 3 Point Sprayers
- Important Operation & Safety Information
- Hooking Up the Sprayer
- Sprayer Boom Controls
- Calibrating the Sprayer
- 5| 30| 1.7| 44′| 6.4| 4.8| 3.8| 2.4| 1.9
- 10| 30| 3.7| 50′| 12.2| 9.2| 7.3| 4.6| 3.7
- 20| 30| 5.1| 54′| 15.6| 11.6| 9.3| 5.8| 4.7
- Operating Instructions
- Spraying with the Boom
- Maintenance Instructions
- FSBK-3025BL (5301289) End Nozzle Assembly & Info
- BXT Series Boomless Boom Component Breakdown & Parts List
- Hamilton Boomless Assembly Component Breakdown & Parts List
- 5282495
- 5273024 (Hypro 6500XL)
- MC-Electric Control Conversion Kits
- Warranty Info
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
OWNER’S MANUAL Cimarron MC1 Series 3 Point Sprayers
60 & 90 Gallon 3-Point Sprayers
60 Gallon (5303641)
90 Gallon (5303642)
MC1 Series 3 Point Sprayers
General Information
Thank You and Congratulations on purchasing your new three point hitch
sprayer. The purpose of this manual is to assist you in operating and
maintaining your 3-Point sprayer.
WARNING: Cancer and Reproductive Harm.
www.P65Warnings.ca.gov
Please read it carefully, as it furnishes information which will help you
achieve years of trouble-free operation. All units can be custom equipped to
meet all your spraying needs. The MC Series 3 Point is designed to fit
Category I Lift Arms.
WARNING: To reduce the risk of injury, the user must read and understand
the operator’s manual before using this product.
Any Questions, Comments or Problems: Call your nearest Cimarron Location and
speak with one of our Friendly Technical Support Staff.
[5195836 (08/23)]
BAKERSFIELD, CA
877-724-2236| COLUMBUS, NE
800-274-1025| DOTHAN, AL
800-227-4098| FARGO, ND
701-280-2862| HOPKINSVILLE, KY
800-637-7172
---|---|---|---|---
MANKATO, MN
507-388-6295| NEWTON, KS
800-394-7662| PASCO, WA
800-634-2026| TEMPE, AZ
877-974-7166|
Important Operation & Safety Information
WARNING
Read and understand this owner’s manual completely before using the sprayer.
Read each chemical label’s instructions before handling the chemical.
Improper use of the sprayer or handling of chemicals could result in serious
injury or illness for the operator or nearby persons/animals, or cause damage
to the environment.
LISTED BELOW is a summary of safety information of particular importance. See
individual sections of this owner’s manual for more details.
———————————- BEFORE YOU BEGIN ————————————-
Please read and understand this manual and its instructions and warnings
completely before operating the sprayer.
- Be aware of all safety guidelines, warnings and cautions including those of the tractor manufacturer
- Read and understand the chemical manufacturer’s labels, warnings and instructions
- Know and fulfill all state pesticide applicator license requirements
- Familiarize yourself and other operators with the sprayer’s components and how all parts are operated
—————————— General Safety Guidelines ———————————
Every year many unnecessary accidents occur do to improper equipment handling
and a disregard for safety precautions.
You, the operator, can avoid accidents by observing the precautions in this
section.
- The operator should be a responsible adult. Do not allow persons to operate this sprayer until they have displayed a thorough understanding of sprayer safety precautions and operational use!
- All operators must also fulfill state pesticide applicator license requirements
- Never attempt to operate this sprayer when under the influence of alcohol or drugs.
- The best defense against accidents is a careful and responsible operator. If your sprayer is equipped with a PTO drive shaft, it is very important to take the proper safety precautions
- Failure to keep body parts or clothing clear of the sprayer’s PTO drive shaft could result in serious injury or death. Cimarron assumes no liability for any possible injury
- Never step over or work near the PTO drive shaft during operation
- When transporting the sprayer on public roads, always follow state and local regulations regarding safety and transportation requirements
———————————– Before Operation ————————————–
- Carefully study and understand the owner’s manual
- Read and follow chemical manufacturer’s labels, warnings and instructions! A material safety data sheet (MSDS) should be provided by the chemical manufacturer
- To avoid injury from chemical hazards, wear the proper protective clothing. Each chemical manufacturer’s clothing requirements are listed under the “Personal Protective Equipment (PPE)” section in the chemical instructions
- Never exceed your tractor’s load rating
- Do not wear loose-fitting clothing which may catch in moving parts
- Give the sprayer a visual inspection for any worn parts, loose bolts or other visible problems and make any needed repairs
- Make sure the area is clear of any people or obstructions before using the sprayer
- Before adding chemicals, have all operators practice operating the sprayer (clean water only) and it’s attachments until all operators are completely capable of safe operation
——————————- BEFORE SEASONAL USE ———————————-
- CHECK and TEST sprayer with water before adding chemical. Temperature change can cause material fitting expansion/ contraction. Serious injury could result from chemical leaks
- REPLACE any worn or frayed hoses. Hose failure can result in serious damage
- INSPECT pressure gauge. Insure the needle rests at zero when all pressure is relieved in the spray system. Failure to have a properly functioning pressure gauge can result in miss applications of chemical
——————————— DURING OPERATION ————————————
- Always be aware of bystanders, particularly children! Always look before moving the sprayer or engaging the PTO
- Never leave running equipment unattended!
- Keep hands and body parts clear of all moving parts, especially the tractor PTO
- Be aware of dangerous terrain such as holes, slopes, drop-offs, banks, rocks and hidden hazards. Operate the tractor and sprayer up and down slopes, not across
- When operating on inclines, it is especially important that your tractor is equipped with Roll Over Protection System (ROPS)
- No passengers are allowed on or in the tractor or sprayer at anytime
- Allow for sprayer boom length when making turns
- Remember that accidents can even happen to seasoned operators. Always take your time and follow all safety instructions
——————————-General Chemical Safety ———————————-
- READ and FOLLOW all chemical label’s instructions and warnings
- AVOID inhaling, ingesting or coming into contact with any chemicals
- KNOW applicable licensing and regulatory requirements for the chemical you plan to use
- KNOW emergency procedures before handling chemicals
- WEAR protective clothing, eye protection and chemical resistant gloves when filling, using and cleaning the sprayer. Wear additional protective gear, such as facemask or apron, as recommended on the chemical label
- EXERCISE EXTRA CAUTION around children or pets. Pesticides are especially toxic to them. Keep sprayer and spray materi- als away from them at all times
- DO NOT MIX OR POUR chemicals in an enclosed, unvented area
- DO NOT USE flammable or corrosive chemicals in the sprayer
- FLUSH the sprayer with clean water after every use AND before switching chemicals
- STORE pesticides in a correctly labeled container and in a secure location
- MONITOR the health of operators frequently exposed to pesticides, as recommended by the chemical label or local/federal regulations
—————————- Chemical Application Safety ——————————-
- INSPECT and PREPARE sprayer before each use as directed
- DO NOT TURN ON POWER to sprayer until ready to spray in order to avoid unintended spray release
- MAKE SURE NOZZLES ARE ORIENTED IN THE PROPER DIRECTION before starting the sprayer. As incorrectly positioned nozzle may spray chemicals on you or others
- KEEP sprayer and spray materials away from children and pets. Pesticides can be especially toxic to children and animals
—————————— Pump Safety Precautions ———————————
- Never pump flammable or explosive fluids such as gasoline, fuel oil, kerosene, etc.
- Never pump acids (i.e. acid fertilizer) with super rollers. For acid fertilizer, Hypro recommends the Silver Series castings with Teflon rollers
- Never run the pump dry! Never pump faster than, or above, the maximum recommended speed and pressure
- Never pump liquids at temperatures higher than the recommended maximum temperature (140° F/60° C). Do not exceed this temperature
- Before servicing your pump, disconnect the power, release all pressure and drain all liquids
——————————— Following Operation ————————————
- Following operation, it is very important that you completely rinse the entire sprayer and all of it’s components of all chemical residue
- Following operation, stop the tractor unit, set the brakes, disengage PTO shaft, shut off the engine and remove the ignition key
- Park the sprayer on a hard level surface
- Store the sprayer away from human and livestock activity
- Do not permit children to play on or around sprayer
Hooking Up the Sprayer
Your MC Series 3 Point sprayer is designed to allow for Category I 3 Point
hitch. The hitch design will fit most brands of 3 Point Quick Tach. The unit
comes standard with Category I lower link pins (7/8”) and top link pin (3/4”).
Once the lower link arms of the tractor are connected to the MC lower pins,
install 3/8”-7/16” retainer pins (NOT Included) to hold the lower arms in
place..
If using a CAT 1 Quick Tach: bushings should be added (NOT Supplied) to match
your Quick Tach System.
Sprayer Boom Controls
Familiarize yourself with the sprayer controls before use. Your sprayer may be
equipped with manual or electric (optional) boom controls.
If your sprayer is equipped with the manual lever controls:
-
Boom Section On/Off Valve–OFF when the lever is down or in the horizontal position, it is ON when the lever is up or in the vertical position.
-
Pressure Relief/Regulating Valve. – loosen the jam nut and screw the knob down to increase pressure and up to decrease pressure.
Once desired pressure is obtained, tighten jam nut. -
Pressure Gauge – Monitor sprayer pressure. DO NOT exceed 100psi. Exceeding 100psi can cause premature gauge failure.
If your sprayer is equipped with electric controls:
Determine the best location for the control box in the vehicle cab, according
to the following guidelines:
- Switches should be within easy reach
- Controller bracket should rest on a flat surface
- 12 volt DC power source must be accessible.
The Electric Control Kit power cord comes with a 3 pin convenience plug. If
your Tractor is not equipped with that type power plug, a Socket 25A is
included in the kit.
The Socket 25A plug will have to be wired into the tractor.
See Socket 25A Wiring Diagram to the right for wiring details
Calibrating the Sprayer
When spraying with a boom, the sprayer must be calibrated to ensure proper
spray coverage and to combat over-application or under application. Before
calibrating the sprayer, it is important to familiarize yourself with the
operating instructions.
The calibration process is simplified when broken down into the following
three steps:
- Determine the speed of the tractor
- Determine the nozzle size and use the calibration chart to find the correct pressure setting
- Set the pressure accordingly using the pressure regulating valve
Note: All calibration must be done with clean water only!
Note: it is helpful for future references to record the exact RPM and
gear that was used to attain the desired speed
Tractor RPM Tractor Gear = Speed
- Determining the Speed
It is important to determine what speed the tractor will be traveling at, while spraying. While some tractors have speedometers, it is still recommended that speed is calculated for all tractors for accuracy purposes. To determine the speed follow these steps:
- Set the tractor throttle to operate between 75%-100% of the tractor’s RPM range. This will allow the pump to operate at full volume
- Measure a 200 foot or 300 foot distance on a field or a surface similar to where you will be spraying
- Drive the tractor and sprayer (tank half-full is optimal) across the measured distance at a constant rate of speed. There should be no changes in speed while you are measuring the time. This should be a comfortable speed for spraying
- Have someone measure the amount of time (in seconds) it takes to travel the measured distance
- Your speed can be found by entering your data into the equation below or by consulting the speed table
Speed (MPH) = (Distance (FT) x 60)/(Time (Seconds) x 88)
(MPH) = (FT) x 60/ _____(SEC) x 88
Note: When calculating tractor speed be sure to select a gear that allows the tractor to operate between 75%-100% of the tractor’s RPM range. This will allow the pump to operate at full volume. Selecting a higher gear will not allow the pump to work efficiently.
Speed Chart
Speed in M.P.H. (Miles Per Hour)| Time Required in seconds to travel a
distance of
100 Ft.| 200 Ft| 300 Ft.
1| 68 sec.| 136| 205
2| 34| 68| 102
3| 23| 45| 68
4| 17| 34| 51
5| 14| 27| 41
6| 11| 23| 34
7| 9.7| 19| 29
8| 8.5| 17| 26
9| 7.6| 15| 23
10| 6.8| 14| 20
2. Determine the nozzle size and use the calibration chart
Always follow the chemical manufacturers label recommendations for application
rate (GPA). There are five things you will need to know to be able to figure
your nozzle size and pressure setting. They are:
- Application rate — GPA or GAL/1000 Sq. Ft.
- Speed — MPH
- Width — Nozzle Spacing (in inches) for broadcast boom spraying — Spray width (in inches) for boomless nozzles
- Spraying Pressure — Follow chemical label recommendations for pressure/droplet size requirements
- Solution weight and conversion factor (CF)
Spraying Solutions Other than Water
Since all the tabulations are based on spraying water, which weighs 8.34 lbs.
per USA gallon, conversion factors must be used when spraying solutions which
are heavier or lighter than water. To determine the proper size nozzle for the
solution to be sprayed, first
multiply the desired GPM or GPA of solution by the rate conversion factor.
Then use the new converted GPM or GPA rate to select the proper size nozzle
and pressure.
Example: Desired application rate is 20 GPA of 28% Nitrogen. Determine
the correct nozzle size as follows:
GPA (Solution) x Conversion Factor = Converted GPA 20 GPA (28% x 1.13 = 22.6
GPA (Water), the applicator should choose a nozzle size that will supply 22.6
GPA of water at the desired pressure. See the appropriate Application Chart
for your boom spraying nozzle or boomless nozzle. Using the tractor speed,
nozzle width or spray width, nozzle size being used and desired gallons per
acre (GPA), find the pressure (psi) necessary to achieve the desired GPA.
Weight of Solution | Specific Gravity | Conversion Factors |
---|---|---|
7.0 lbs. per gallon | .84 | .92 |
8.0 lbs. per gallon | .96 | .98 |
8.345 lbs. per gallon(Water) | 1.00 | 1.00 |
9.0 lbs. per gallon | 1.08 | 1.04 |
10.0 lbs. per gallon | 1.20 | 1.10 |
10.66 lbs. per gallon(28% Nitrogen) | 1.28 | 1.13 |
11.0 lbs. per gallon | 1.32 | 1.15 |
12.0 lbs. per gallon | 1.44 | 1.20 |
14.0 lbs. per gallon | 1.68 | 1.30 |
Example for traditional boom sprayer: Assume you have found your tractor speed
to be 6 MPH, your nozzle spacing is 20”, and you want to spray 15 GPA and your
sprayer has blue AIXR11003VP nozzles. Upon looking at the application chart,
you will find that you should set the sprayer’s pressure at about 40 psi in
order to apply about 15 GPA.
Example for boomless sprayer: Assume you have found your tractor speed to be 5
MPH, your nozzle will cover 216 inches (18 Ft) mounted 48” height above the
target spray zone, and you will want to spray 15 GPA and your sprayer has
yellow XT024 nozzles.
Upon looking at the application chart, you will find that you should set the
sprayer’s pressure at about 50 psi in order to apply about 15 GPA.
Useful Formulas
GPM (Per Nozzle) = GPA x MPH x W 5,940
GPM (Per Nozzle = GAL/1000 Sq. Ft. x MPH x W 136
GPM — Gallons Per Minute
GPA — Gallons Per Acre
GAL/1000 Sq. Ft. — Gallons Per 1000 Square Feet
MPH — Miles Per Hour
W — Nozzle Spacing (in inches) for broadcast spraying
— Spray width (in inches) for single nozzle, Band spraying or Boomless
spraying
3. Adjusting the Sprayer Pressure
Once you have found the correct pressure (psi) setting, you must now adjust
the sprayer to that pressure setting. Before you adjust the sprayer’s
pressure, it is important to follow these steps:
- Make sure the sprayer tank is at least half full of clean water and the tank supply shutoff valve to the pump is open.
- Make sure the pressure relief valve is backed out so at least 4 threads are showing. If not, loosen the jam nut and screw the knob out until at least 4 threads can be seen.
- Make sure the valves to the agitator are open, if equipped.
- With the booms on, idle tractor and engage the tractor PTO to start the pump. Slowly increase tractor RPM, paying attention to the sprayer pressure gauge. (Do NOT spike the sprayer pressure gauge). If you over pressurize the spray system you can damage the pressure gauge and sprayer plumbing. Increase the tractor’s RPM until you reach RPM that was used to set the tractor’s speed.
- Adjust the pressure relief valve to reach your desired psi for your speed and GPA. This is achieved by loosening the jam nut on the pressure relief valve and screwing the knob in to increase pressure and out to decrease pressure. Once you have reached your desired pressure, tighten the jam nut to lock the pressure control knob. If you can not achieve enough pressure, slowly close the agitation valve. Tighten the valve nut to lock the agitation valve, if equipped.
You have successfully calibrated the sprayer.
PISTON TYPE PRESSURE RELIEF/REGULATING VALVE
Bypasses excess liquid. Adjustable to maintain control of line pressure at any
pressure within the valve operating range.
Selected pressure setting firmly held in place by locknut. Extra large
passages to handle large flows.
- Polypropylene with stainless steel spring
- Excellent chemical resistance
- EPDM O-Rings
- For pressure to 150 p.s.i.
- 1/4” port for pressure gauge
- 3/4” NPT (M) inlet & (F) outlet connections
Ref. # | Part # | Mfg. Part # | Description | Qty |
---|---|---|---|---|
1 | 5046270 | CP23122-NY | Adjusting Cap, Nylon (Gray) | 1 |
2 | 5110266 | CP23123-PP | Lock Ring | 1 |
3 | ♦♦ | CP23124-PP | Spring Retainer | 1 |
4 | CP7717-15-EPR | 0-Ring, EPDM Rubber | 1 | |
5 | CP23127-302SS | Spring | 1 | |
6 | ♦♦ | CP23125-PP | Guide Seat | 1 |
7 | ** | CP23126-302SS | Retaining Pin | 1 |
8 | CP23121-PP | CP23121-PP | Poly Body (3/4″ NPT) | 1 |
9 | CP23128-PP | CP23128-PP | Poly Body (1/2″ NPT) | 1 |
10 | 5102022 | F14 | Pipe Plug, 1/4″ MNPT | 1 |
Fimco # | Mfg. Part # | Description | ||
--- | --- | --- | ||
5143199 | 23120-3/4-PP | Pressure Relief Valve (3/4″ NPT) | ||
5143200 | 23120-1/2-PP | Pressure Relief Valve (1/2″ NPT) | ||
5168717 | PK-AB23120-KIT | Repair Kit, Items Marked ‘ ‘ |
-
- Available only in Repair Kit
Only Available in Complete Assembly
Calibration Chart
There are many different sizes and styles of spray tips available to meet your spraying needs. If you need further information, please contact an Cimarron Service Center for assistance.
Please Note: Flow rates are calculated using fresh water.
Always remember to double check application rates.
Boomless Nozzle Application
Hypro Boom X Tender
Boomless Nozzles NOTE: Application rates are based on overall swath widths listed at 48” height. Refer to operating instructions if using a different swath.
HAMILTON BOOMLESS NOZZLES
- Available only in Repair Kit
Operating Data for 1800 Nozzles
Orifice
No.| PSI| GPM
180°| Swath
180°| Gallons per Acre
3 MPH| 4 MPH| 5 MPH| 8 MPH| 10 MPH
5| 30| 1.7| 44′| 6.4| 4.8| 3.8| 2.4| 1.9
40| 2.0| 46′| 7.2| 5.4| 4.3| 2.7| 2.2
50| 2.2| 48′| 7.6| 5.7| 4.5| 2.9| 2.3
60| 2.4| 50′| 7.9| 5.9| 4.8| 3.0| 2.4
10| 30| 3.7| 50′| 12.2| 9.2| 7.3| 4.6| 3.7
40| 4.2| 50′| 13.9| 10.4| 8.3| 5.2| 4.2
50| 4.6| 52′| 14.6| 10.9| 8.8| 5.5| 4.4
60| 5.0| 52′| 15.8| 11.9| 9.5| 5.9| 4.8
20| 30| 5.1| 54′| 15.6| 11.6| 9.3| 5.8| 4.7
40| 5.9| 54′| 18| 13.5| 10.8| 6.8| 5.4
50| 6.7| 56′| 19.7| 14.8| 11.8| 7.4| 5.9
60| 7.1| 58′| 20.2| 15.1| 12.1| 7.6| 6.1
NOTE: 90° nozzles have the same GPA, but 1/2 GPM and swath
BROADCAST & TURF APPLICATION CHART—20” SPACING KLC FieldJet Nozzles used on FSBK-1
Boom Assembly
The KLC FieldJet nozzle is typically used to spray areas not accessible with a
boom sprayer. It’s one-piece nozzle design projects spray to both sides to
form a wide swath flat spray. The round orifice minimizes clogging. Uniformity
across the swath is not as good as with a properly operated boom sprayer.
Available in brass or stainless steel.
(Uniformity can be optimized by double overlapping spray swaths on successive
sprayer passes. Remember, this also doubles the application volume.)
Rate Chart: Type 1/4-KLC and Type 3/4-KLC FieldJet Nozzles
Tip Number| Pioe Connection| PSI| Capacity (One Nozzle) in GPM| „w„ in Feet|
GPA (Gallons per Acre)| GPA (Gallons per 1000 Sq. Ft.)
---|---|---|---|---|---|---
3 MPH| 4 MPH| 5 MPH| 8 MPH| 3 MPH| 4 MPH| 5 MPH| 8 MPH
1/4KLC-5| 1/4″| 20| 0.71| 17| 6.9| 5.2| 4.1| 2.6| 0.16| 0.12| 0.09| 0.06
30| 0.87| 18| 8.0| 6.0| 5.| 3.0| 0.18| 0.14| 0.11| 0.07
40| 1.00| 21| 7.9| 5.9| 5.| 3.| 0.18| 0.13| 0.11| 0.07
1/4KLC-9| 1/4″| 20| 1.56| 18| 12.| 8.7| 7.0| 4.| 0.27| 0.20| 0.16| 0.10
30| 2.55| 19| 11.6| 10.2| 8.| 5.1| 0.31| 0.23| 0.19| 0.12
40| 1.80| 21| 13.5| 10.6| 9.| 5.3| 0.32| 0.24| 0.19| 0.12
1/4KLC-18| 1/4″| 20| 3.12| 20| 14.1| 15.8| 13.| 7.9| 0.48| 0.36| 0.29| 0.18
30| 3.60| 21| 25.0| 18.4| 15.| 9.2| 0.56| 0.42| 0.34| 0.21
40| 3.60| 22| 27.0| 20.0| 16.| 10.1| 0.62| 0.46| 0.37| 0.23
1/4KLC-36| 1/4″| 20| 5.09| 22| 38.0| 29.0| 23.0| 14.3| 0.87| 0.66| 0.52| 0.33
30| 6.24| 24| 43.0| 32.0| 26.0| 16.1| 0.98| 0.74| 0.59| 0.37
40| 7.20| 26| 46.0| 34.0| 27.0| 17.1| 1.00| 0.78| 0.63| 0.39
NOTE: Always double-check your application rates.
Turbo FloodJet Nozzles used Based on the minimum overlap required to obtain
uniform distribution with 120° tips and 40” spacing.
Suggested Minimum Spray Height: 18”20” above what is being sprayed (to plant,
not ground).
Optimum Spray Height: 39”
Wide angle spray nozzle height is influenced by nozzle orientation.
The critical factor is to achieve a minimum 30% overlap.
Turbo FloodJet Nozzles used on FSBK-2 Boom Assembly
Tip Chart for TKT-VP3, TF-VP3 & 30DT3.0 (Gray) Tips
| Pressure (psi)| Capacity (GPM)| 1 MPH| 2 MPH| 3 MPH| 4 MPH| 5 MPH| 7.5 MPH|
10 MPH
Gallons Per AcreBased on Water| 10| .30| 44| 22| 14.9| 11.1| 8.9| 5.9| 4.5
20| .42| 63| 31.5| 20.9| 15.7| 12.6| 8.4| 6.3
30| .52| 76| 38| 26| 19.3| 15.4| 10.3| 7.7
40| .60| 90| 45| 30| 22| 17.8| 11.8| 8.9
Gallons Per
1000 Sq. Ft.
Based on Water| 10| .30| 1.01| .5| .34| .254| .204| .135| .103
20| .42| 1.4| .72| .48| .36| .29| .19| .14
30| .52| 1.74| .87| .596| .44| .35| .236| .176
40| .60| 2.06| 1.00| .688| .50| .408| .27| .20
Gallons Per
100 Sq. Ft.
Based on Water| 10| .30| .10| .05| .034| .025| .02| .013| .01
20| .42| .14| .072| .048| .036| .029| .019| .014
30| .52| .174| .087| .059| .044| .035| .023| .017
40| .60| .206| .10| .068| .05| .04| .027| .02
AIXR11002VP Nozzles used on FSBK-5 & FSBK-70 Boom Assemblies
AIXR11002VP Spray Tip Rate Chart (20″ Spacing)
| Pressure
(psi)| Capacity
(GPM)| 1
MPH| 2
MPH| 3
MPH| 4
MPH| 5
MPH| 6
MPH| 8
MPH| 10
MPH
Gallons PerAcreBased on Water| 15| .12| 35.6| 17.8| 11.8| 8.9| 7.1| 5.9| 4.5|
3.6
20| .14| 41.6| 20.8| 13.8| 10.4| 8.3| 6.9| 5.2| 4.2
30| .17| 50.4| 25.2| 16.8| 12.6| 10.1| 8.4| 6.3| 5.0
40| .20| 59.6| 29.8| 19.8| 14.9| 11.9| 9.9| 7.4| 5.9
Gallons Per 1000 Sq. Ft.
Based on Water| 15| .12| | .41| .27| .20| .16| | |
20| .14| | .48| .32| .24| .19| | |
30| .17| | .58| .39| .29| .23| | |
40| .20| | .68| .45| .34| .27| | |
Based on the minimum overlap required to obtain uniform distribution with 110°
tips and 20” spacing.
Suggested Minimum Spray Height: 16”-18” above what is being sprayed (to plant,
not ground).
Optimum Spray Height: 20”
Operating Instructions
Before operating the sprayer, it is important that you read this entire manual and know all the safety precautions. Always take your time and be alert when operating your sprayer. This will allow you to safely spray without accident or interruption.
Spraying with the Boom
-
Calibrate the sprayer using the calibration instructions and application charts. This will determine what pressure to spray at in order to achieve the desired Gallons per Acre (GPA).
-
Connect the PTO coupler and torque bar to the tractor.
-
Fill the tank with some water in order to set the pressure and test for leaks.
-
Prepare the sprayer for spraying. Open the ball valve on the suction line, make sure the boom valves are off and make sure the spray gun is closed (if applicable).
-
Start the tractor and engage the pump. The tractor should be running at the RPM rate determined when you calibrated your sprayer. Ensure that the pump is primed and that there are no leaks in any of the lines.
-
Using the relief valve (manual controls), or pressure adjustment switch (electric controls), adjust the sprayers pressure to the pressure rating found when you calibrated your sprayer. You may need to readjust the pressure when you open the boom control valves.
-
You may now fill the tank with the amount of water and chemicals recommended by the chemical manufacturer. Before filling the tank make sure the pump is disengaged.
-
After filling the tank, engage the pump and allow an ample amount of time for the jet agitator to mix the water and chemicals.
Note: See chemical instructions for necessary agitation time. You are now ready to begin spraying. -
Upon arriving at the spraying location, unfold booms (if applicable), engage pump, open the boom control valves and make sure the pressure setting is correct. While spraying always remember to maintain constant level of speed and RPM (rates found when calibrated).
Spraying with the Spray Gun
-
Connect the pump’s PTO coupler and torque bar.
-
Fill the tank with some water in order to set the pressure and test for leaks.
-
Make sure the spray gun is closed and the booms are off.
-
Start the tractor and engage the pump. Ensure that the pump is primed and that there are no leaks in any of the lines.
-
Adjust the sprayer’s pressure using the relief valve to your desired setting. When you open the spray gun, you may need to readjust the pressure.
-
You may now fill the tank with the amount of water and chemicals recommended by the chemical manufacturer. Before filling the tank make sure the pump is disengaged.
-
After filling the tank, engage the pump and allow an ample amount of time for the jet agitator to mix the water and chemicals.
Note: See chemical instructions for necessary agitation time. You are now ready to begin spraying. -
Upon arriving at the spraying location, engage the pump and make sure the pressure setting is correct. Adjust the gun to the desired spray pattern when spraying.
Maintenance Instructions
Routine Maintenance
It is very important to perform routine maintenance on your sprayer before and
after each use. Good maintenance practices will help to guard against sprayer
breakdowns or accidents.
-
It is recommended to perform a visual and physical inspection for any worn parts, loose bolts or other visible problems. Make all necessary repairs before spraying. Please contact an authorized Cimarron dealer to order parts or to receive technical help.
-
After each use, it is important to rinse the sprayer and all components by running a good quality tank cleaner (Tank Neutralizer and Cleaner) through the system (if no tank cleaner is available, you may substitute a good grade of dish soap for this step. Turn pump on and circulate through the sprayer for 15 minutes and then spray out through boom and handgun nozzles. Refill sprayer part way with clean fresh water and repeat. Rinsing the sprayer after use will greatly improve the life of the pump and other components.
-
Failure to properly rinse the sprayer and all components after each use, will void the manufacturer’s warranty.
Note: All rinsates must be sprayed in field according to chemical regulations! -
The screen of the in-line filter on the suction line should be taken out and rinsed. Note: Be careful not to lose the gasket in the filter bowl. The filter will leak without this gasket.
-
Tip strainer (if applicable), should also be taken out and rinsed after each use. Tips strainers are small screens that are located behind each spray nozzle on the boom.
Pump Maintenance
- Follow all pump safety precautions and warnings. Following these guidelines will help to ensure many years of smooth and trouble-free service.
- Flush the pump, as directed in routine maintenance, after every use. It is also very important to winterize your pump to prevent freezing and corrosion. Please see Winterizing your Sprayer section below for instructions.
- After many years of use, you may find that your pump is leaking or has experienced a decrease in performance. You may need to change the seals and rollers. Contact an authorized Cimarron Dealer for parts and technical support.
Drain the Tank
Close the valve on the tank outlet. Remove the filter bowl by unscrewing from
the filter body. Pay attention when removing the filter bowl that the screen
and gasket be removed and kept with the bowl.
Once the filter bowl, screen and gasket have been removed, open the valve on
the tank outlet to allow the fluid to drain from the tank. While the filter
screen is off, rinse with clean water and inspect to make sure in good
operating condition. When done, reinstall filter bowl with gasket and screen.
Winterizing your Sprayer
It is essential that you winterize your sprayer to avoid damage and to allow
for optimal performance. The winterization process should be undertaken before
freezing conditions and/or after each season of use. Failure to winterize your
sprayer will void the manufacturer’s warranty.
- Verify that the tank is empty and rinsed out. Pour 1-2 gallons of RV nontoxic antifreeze into the tank. It is not recommended to use engine antifreeze. Engine antifreeze can be harmful to humans, animals, crops and the environment.
- Engage the pump and spray with the boom and spray gun (if applicable). Make sure that the antifreeze has been pumped through the entire system, including all spray nozzles.
- See pump manufacturers operators manual for proper winter storage of your sprayer pump.
- Before spraying in the spring, it is recommended to flush the sprayer with fresh water to cleanse it of the antifreeze and any other buildup. It would also be beneficial to do a thorough inspection of all sprayer components before spraying.
MC1 60 Gallon 3-PT Component Breakdown & Parts List
Ref. # | Part # | Description | Qty |
---|---|---|---|
1 | 5169364 | 60 Gallon MC1 Tank (Yellow) | 1 |
1.1 | 63600 | Norwesco 8″ Lid Gasket | 1 |
1.2 | 60032 | Norwesco 8″ Lid w/Vent & Ring Assembly | 1 |
1.2.1 | 60003 | 8″ Tank Lid Ring ONLY (for TL8N Lid) | 1 |
1.2.2 | TL8N | 8″ Poly Tank Lid w/Airvent | 1 |
2 | 5282516 | MC1 Tank Drain w/Strainer Assembly | 1 |
2.1 | 5010244 | Poly Street Elbow, 3/4″ FNPT x 3/4″ MNPT | 1 |
2.2 | 5011140 | Poly Close Nipple, 3/4″ MNPT | 2 |
2.3 | 5143407 | 3/4″ Union Poly Ball Valve | 1 |
2.4 | 5116322 | 3/4″ Black Poly Strainer | 1 |
2.4.1 | 5072229 | EPDM Gasket | 1 |
2.4.2 | 5116323 | 40 Mesh Screen | 1 |
3. | 5010210 | Poly Elbow, 3/4″ MNPT x 1″ HB | 1 |
3 | 5070255-BLK | Control Mount Bracket | 1 |
4 | 5034604 | 5/16-18 x 0.5 Flng Hex Bolt | 4 |
5 | 5282517 | MC1 1-SEC Control Assembly | 1 |
5.1 | 5034038 | 5/16-18 x 0.75 Hex Bolt | 4 |
5.2 | 5282495 | ARAG NPT+1 Two SEC Valve Assembly | 1 |
5.2.1 | 1091320 | T3 Male x 3/4″ Hose Barb Straight | 1 |
5.2.2 | 1091313 | T3 Male x 1/2″ Hose Barb Straight | 1 |
Ref. # | Part # | Description | Qty |
--- | --- | --- | --- |
5.2.3 | 219150 | T5 Male Plug Fitting | 1 |
5.2.4 | 463T001.010 | Single 463T Body Bare | 1 |
5.2.5 | 5143560 | 1-Sec. Manual Valve T5XT3 | 1 |
5.2.6 | 239133N | 3/4″ FNPT x T3 Male Fitting | 1 |
5.2.7 | 219050 | T5 Female Blank Cap | 1 |
5.3 | 5006389 | 5/16-18 FIng Top-Lock Hex Nut | 4 |
5.4 | 5143199 | Pressure Relief Valve, (3/4″ NPT) | 1 |
5.5 | 5167108 | 2 1/2″ Liquid Filled 100# Back Mount Gauge | 1 |
5.6 | 5010207 | Poly Elbow, 3/4″ MNPT x 1/2″ HB | 1 |
6 | 5010207 | Poly Elbow, 3/4″ MNPT x 1/2″ HB | 1 |
7 | 5282512-BLU | MC1 3PT Frame Assembly | 1 |
8 | 5034764 | 3/8-16 x 1.00 FIng Hex Bolt | 4 |
9 | 5070253-BLU | MC1 Tank Retainer | 2 |
10 | LAP1 | Lift Arm Pin, CAT I-II, 1 1/8″ Dia. x 1 13/16″ Usable Length | 2 |
11 | 5101356 | Top Link Pin 3/4″ Dia. x 3 7/8″ Usable | 1 |
12 | 5101260 | 5/16″ x 1-3/4″ Lynch Pin | 1 |
13 | 5117317 | 1/4-20 x 0.50 PH Pan Head Self-Tapping Screw | 2 |
14 | 70111 | Owner’s Manual Canister (Small) | 1 |
Not Shown:
EPDM12 | 5 Ft. | 1/2” – 200 PSI EPDM Spray Hose | HC08 | Qty.: 2 | 1/2” Hose Clamp |
---|---|---|---|---|---|
EPDM34 | 5 Ft. | 3/4” – 200 PSI EPDM Spray Hose | HC12 | Qty.: 2 | 3/4” Hose Clamp |
KF1300BLK | 4 Ft. | 1”-50 PSI Kanaflex Suction Hose | HC16 | Qty.: 2 | 1” Hose |
Clamp
MC1 90 Gallon 3-PT Component Breakdown & Parts List
Ref. # | Part # | Description | Qty |
---|---|---|---|
1 | 5169365 | 90 Gallon MC1 Tank (Yellow) | 1 |
1.1 | 63600 | Norwesco 8″ Lid Gasket | 1 |
1.2 | 60032 | Norwesco 8″ Lid w/Vent & Ring Assembly | 1 |
1.2.1 | 60003 | 8″ Tank Lid Ring ONLY (for TL8N Lid) | 1 |
1.2.2 | TL8N | Norwesco 8″ Poly Tank Lid w/Airvent | 1 |
2 | 5282516 | MC1 Tank Drain w/Strainer Assembly | 1 |
2.1 | 5010244 | Poly Street Elbow, 3/4″ FNPT x 3/4″ MNPT | 1 |
2.2 | 5011140 | Poly Close Nipple, 3/4″ MNPT | 2 |
2.3 | 5143407 | 3/4″ Union Poly Ball Valve | 1 |
2.4 | 5116322 | 3/4″ Black Poly Strainer | 1 |
2.4.1 | 5072229 | EPDM Gasket | 1 |
2.4.2 | 5116323 | 40 Mesh Screen | 1 |
2.5 | 5010210 | Poly Elbow, 3/4″ MNPT x 1″ HB | 1 |
3 | 5070256-BLK | Control Mount Bracket | 1 |
4 | 5034604 | 5/16-18 x 0.5 Flng Hex Bolt | 4 |
5 | 5282517 | MC1 1-SEC Control Assembly | 1 |
5.1 | 5034038 | 5/16-18 x 0.75 Hex Bolt | 4 |
5.2 | 5282495 | ARAG NPT+1 Two SEC Valve Assembly | 1 |
5.2.1 | 1091320 | T3 Male x 3/4″ Hose Barb Straight | 1 |
5.2.2 | 1091313 | T3 Male x 1/2″ Hose Barb Straight | 1 |
Ref. # | Part # | Description | Qty |
--- | --- | --- | --- |
5.2.3 | 219150 | T5 Male Plug Fitting | 1 |
5.2.4 | 463T001.010 | Single 463T Body Bare | 1 |
5.2.5 | 5143560 | 1-SEC Manual Valve T5XT3 | 1 |
5.2.6 | 239133N | 3/4″ FNPT x T3 Male Fitting | 1 |
5.2.7 | 219050 | T5 Female Blank Cap | 1 |
5.3 | 5006389 | 5/16-18 Flng Top-Lock Hex Nut | 4 |
5.4 | 5143199 | Pressure Relief Valve, (3/4″ NPT) | 1 |
5.5 | 5167108 | 2 1/2″ Liquid Filled 100# Back Mount Gauge | 1 |
5.6 | 5010207 | Poly Elbow, 3/4″ MNPT x 1/2″ HB | 1 |
6 | 5010207 | Poly Elbow, 3/4″ MNPT x 1/2″ HB | 1 |
7 | 5282512-BLU | MC1 3PT Frame Assembly | 1 |
8 | 5034764 | 3/8-16 x 1.00 Flng Hex Bolt | 4 |
9 | 5070253-BLU | MC1 Tank Retainer | 2 |
10 | LAP1 | Lift Arm Pin, CAT I-II, 1 1/8″ Dia x 1 13/16″ Usable Length | 2 |
11 | 5101356 | Top Link Pin 3/4″ Dia. x 3 7/8″ Usable | 1 |
12 | 5101260 | 5/16″ x 1-3/4″ Lynch Pin | 1 |
13 | 5117317 | 1/4-20 x 0.50 PH Pan Head Self-Tapping Screw | 2 |
14 | 70111 | Owner’s Manual Canister (Small) | 1 |
Not Shown:
EPDM12 | 5 Ft. | 1/2” – 200 PSI EPDM Spray Hose | HC08 | Qty.: 2 | 1/2” Hose Clamp |
---|---|---|---|---|---|
EPDM34 | 5 Ft. | 3/4” – 200 PSI EPDM Spray Hose | HC12 | Qty.: 2 | 3/4” Hose Clamp |
KF1300BLK | 4 Ft. | 1”-50 PSI Kanaflex Suction Hose | HC16 | Qty.: 2 | 1” Hose |
Clamp
FSBK-5 (5300976) Component Breakdown & Parts List
Ref. # | Part # | Description | Qty |
---|---|---|---|
1 | 5277779 | Boom Sub-Assembly (1″ Sq. Tube) | 1 |
1.1 | 5277838-BLK | Center Boom Tube 1″ Sq. | 1 |
1.2 | 5277834-BLK | LH Outer Boom Tube 1″ Sq. | 1 |
1.3 | 5277835-BLK | RH Outer Boom Tube 1″ Sq. | 1 |
1.4 | 5006345 | 318″-16 Flange Locknut (Grade F) | 6 |
1.5 | 5006259 | 3/8″-16 Hex Whiz (Flange) Locknut | 4 |
1.6 | 5019228 | Extension Spring | 2 |
1.7 | 5034169 | H.H.C.S., 3/8″-16 x 2 1/2″ | 2 |
1.8 | 5046106 | Square Cap, Black (1″ Square Tube) | 2 |
2 | 5277695 | 5-Nozzle Harness (3/8″ & 1″ Sq Tube) | 1 |
2.1 | 5020534 | Hose, 3/8″-1 Brd. x 21″ | 2 |
2.2 | 5020531 | Hose, 318″-1 Brd. x 19-3/8″ | 2 |
2.3 | 5051144 | Hose Clamp, 3/8″ | 8 |
2.4 | 5277689 | “ELL” Nozzle Sub-Assembly (3/8″) | 2 |
2.4.1 | 5056113 | Single Hose Shank (3/8″ Hose) | 1 |
2.4.2 | 5143543 | Check Valve Strainer, 50 Mesh, 5 PSI | 1 |
2.4.3 | 5016157 | Seat Washer (QJ Caps) | 1 |
2.4.4 | 5018371 | Air-Induction XR Flat Spray Tip (AIXR11002VP) | 1 |
2.4.5 | 5046219 | Quick TeeJet Cap ONLY (Yellow) | 1 |
2.5 | 5277690 | “TEE” Nozzle Sub-Assembly (3/8″) | 2 |
Ref. # | Part # | Description | Qty |
--- | --- | --- | --- |
2.5.1 | 5056114 | Double Hose Shank (3/8″ Hose) | 1 |
2.5.2 | 5143543 | Check Valve Strainer, 50 Mesh, 5 PSI | 1 |
2.5.3 | 5016157 | Seat Washer (QJ Caps) | 1 |
2.5.4 | 5018371 | Air-Induction XR Flat Spray Tip (AIXR11002VP) | 1 |
2.5.5 | 5046219 | Quick TeeJet Cap ONLY (Yellow) | 2 |
3. | 5277691 | “Cross” Nozzle Sub-Assembly (3/8″) | 1 |
2.6.1 | 5056115 | Triple Hose Shank (3/8″ Hose) | 1 |
2.6.2 | 5143543 | Check Valve Strainer, 50 Mesh, 5 PSI | 1 |
2.6.3 | 5016157 | Seat Washer (QJ Caps) | 1 |
2.6.4 | 5018371 | Air-Induction XR Flat Spray Tip (AIXR11002VP) | 1 |
2.6.5 | 5046219 | Quick TeeJet Cap ONLY (Yellow) | 1 |
3 | 5277923 | Boom Clamp Assembly (1in Sq.) | 5 |
4 | 5034159 | Square U-Bolt, 5/16″ x 1 5/16″ x 1 7/8″ | 2 |
5 | 5006307 | 5/16″-18 Hex Whiz (Flange) Locknut | 4 |
6 | 5277926 | 1/2″ Hose to 3/8″ Hose Conversion Kit | 1 |
6.1 | 5067228 | 1/2″ x 3/8″ Poly Hose Mender | 1 |
6.2 | 5020417 | Hose, 3/8″-1 Brd. x 5-1/2″ | 1 |
6.3 | 5051144 | Hose Clamp, 3/8″ | 2 |
FSBK-70 (5301100) Component Breakdown & Parts List
Ref. # | Part # | Description | Qty |
---|---|---|---|
1 | 5277780 | 7-Nozzle Boom Assembly | 1 |
1.1 | 5277838-BLK | Center Boom Weldment (1″ Sq. Tube) | 1 |
1.2 | 5277837-BLK | Outer Boom Weldment (LH) (1″ Sq Tube) | 1 |
1.3 | 5277836-BLK | Outer Boom Weldment (RH) (1″ Sq Tube) | 1 |
1.4 | 5046106 | Square Cap, Black (1″ Square) | 2 |
1.5 | 5019228 | Extension Spring | 2 |
1.6 | 5006259 | 3/8″-16 Hex Whiz (Flange) Locknut | 4 |
1.7 | 5034169 | H.H.C.S., 3/8″-16 x 2 1/2″ | 2 |
1.8 | 5006345 | 3/8″-16 Flange Locknut | 6 |
2 | 5277696 | 7-Nozzle Harness (3/8″) | 1 |
2.1 | 5281304 | “ELL” Nozzle Sub-Assembly (3/8″) | 2 |
2.1.1 | 5056113 | Single Hose Shank (3/8″ Hose) | 1 |
2.1.2 | 5143543 | Nozzle Strainer, Blue (50 Mesh) | 1 |
2.1.3 | 5016157 | Seat Washer (QJ Caps) | 1 |
2.1.4 | 5018371 | Air-Induction XR Flat Spray Tip (AIXR11002VP) | 1 |
2.1.5 | 5046219 | Quick TeeJet Cap ONLY (Yellow) | 1 |
2.2 | 5281307 | “TEE” Nozzle Sub-Assembly (3/8″) | 4 |
2.2.1 | 5056114 | Double Hose Shank (3/8″ Hose) | 1 |
2.2.2 | 5143543 | Nozzle Strainer, Blue (50 Mesh) | 1 |
2.2.3 | 5016157 | Seat Washer (QJ Caps) | 1 |
Ref. # | Part # | Description | Qty |
--- | --- | --- | --- |
2.2.4 | 5018371 | Air-Induction XR Flat Spray Tip (AIXR11002VP) | 1 |
2.2.5 | 5046219 | Quick TeeJet Cap ONLY (Yellow) | 1 |
2. | 5281308 | “Cross” Nozzle Sub-Assembly (3/8″) | 1 |
2.3.1 | 5056115 | Triple Hose Shank (3/8″ Hose) | 1 |
2.3.2 | 5143543 | Nozzle Strainer, Blue (50 Mesh) | 1 |
2.3.3 | 5016157 | Seat Washer (QJ Caps) | 1 |
2.3.4 | 5018371 | Air-Induction XR Flat Spray Tip (AIXR11002VP) | 1 |
2.3.5 | 5046219 | Quick TeeJet Cap ONLY (Yellow) | 1 |
2.4 | 5020510 | Hose, 3/8″-1 Brd. x 19-3/8″ | 4 |
2.5 | 5020347 | Hose, 3/8″-1 Brd. x 21″ | 2 |
2.6 | 5051144 | Hose Clamp, 3/8″ | 12 |
3 | 5277923 | Boom Clamp Assembly (1in Sq.) | 7 |
4 | 5034159 | Square U-Bolt, 5/16″ x 1 5/16″ x 1 7/8″ | 2 |
5 | 5006307 | 5/16″-18 Hex Whiz (Flange) Locknut | 4 |
6 | 5277926 | 1/2″ Hose to 3/8″ Hose Conversion Kit | 1 |
6.1 | 5067228 | 1/2″ x 3/8″ Poly Hose Mender | 1 |
6.2 | 5020417 | Hose. 3/8″-1 Brd. x 5-1/2″ | 1 |
6.3 | 5051144 | Hose Clamp, 3/8″ | 2 |
MX4 Series Boom Component Breakdown & Parts List
Ref. # | Part # | Description |
---|---|---|
1A | 5002514 | Single 1/2″ HB Nozzle Dry Boom Adapter (RH/LH) |
1B | 5002513 | Double 1/2″ HB Nozzle Dry Boom Adapter |
10 | 5002514 | Single 1/2″ HB Nozzle Dry Boom Adapter (RH/LH) |
2 | 5056125 | QJ17560A-1/2, 1/2″ Wet Boom QJ Nozzle Body |
3 | 5116019 | Nozzle Strainer, Blue (50 Mesh) |
4 | 5016157 | Seat Washer – EPDM – QJ Caps |
5 | AIXR11003VP | Air-Induction XR Flat Spray Tip |
6 | 5046217 | Quick Cap – Blue |
MX4 Series Boom Component Breakdown & Parts List
Ref. # | Part # | Description | 408 | 410 | 412 |
---|---|---|---|---|---|
1 | 5282551-BLK | MX4 Center Section | 1 | 1 | 1 |
2 | 5034871 | 5/16-18 x 1.75 Carriage Bolt | 4 | 4 | 4 |
3-A | 5282563 | MX4 2-Nozzle Wing Assembly, LH | 1 | — | — |
3-B | 5282565 | MX4 3-Nozzle Wing Assembly, LH | — | 1 | — |
3-C | 5282567 | MX4 4-Nozzle Wing Assembly, LH | — | — | — |
3.1 | 5282560-BLK | MX4, LH Wing Mount | 1 | 1 | 1 |
3.2 | 5101378 | Pivot Pin | 1 | 1 | 1 |
3.3 | 5016323 | 3/4 (.785) X 1.50″ OD Flat Washer | 1 | 1 | 1 |
3.4 | 5019762 | Compression Spring, 3 3/4″ | 1 | 1 | 1 |
3.5 | 5034869 | 5/8-18 Top-Lock Hex Jam Nut | 1 | 1 | 1 |
3.6 | 5012025 | 3/16″ Straight Drive Bal Check Grease Fitting | 1 | 1 | 1 |
3.7A | 5282554-BLK | MX4 2-Nozzle Wing, LH | 1 | — | — |
3.7B | 5282556-BLK | MX4 3-Nozzle Wing, LH | — | 1 | — |
3.7C | 5282558-BLK | MX4 4-Nozzle Wing, LH | — | — | 1 |
3.8 | 5046106 | Square Cap, Black (1″ Square Tube) | 1 | 1 | 1 |
4 | 5006389 | 5/16-18 Flng Top-Lock Hex Nut | 8 | 9 | 5 |
5-A | 5282564 | MX4 2-Nozzle Wing Assembly, RH | 1 | — | — |
5-B | 5282566 | MX4 3-Nozzle Wing Assembly, RH | — | 1 | — |
5-C | 5282568 | MX4 4-Nozzle Wing Assembly, RH | — | — | — |
5. | 5282561-BLK | MX4, RH Wing Mount | 1 | 1 | 1 |
5. | 5101378 | Pivot Pin | 1 | 1 | 1 |
5. | 5016323 | 3/4 (.785) X 1.50″ OD Flat Washer | 1 | 1 | 1 |
5. | 5019762 | Compression Spring, 3 3/4″ | 1 | 1 | 1 |
6. | 5034869 | 5/8-18 Top-Lock Hex Jam Nut | 1 | 1 | 1 |
6. | 5012025 | 3/16″ Straight Drive Bal Check Grease Fitting | 1 | 1 | 1 |
5.7A | 5282555-BLK | MX4 2-Nozzle Wing, RH | — | — | — |
5.7B | 5282557-BLK | MX4 3-Nozzle Wing, RH | — | 1 | — |
5.7C | 5282559-BLK | MX4 4-Nozzle Wing, RH | — | — | 1 |
5.8 | 5046106 | Square Cap, Black (1″ Square Tube) | 1 | 1 | 1 |
6 | 5051179-BLK | MX4 Saddle Mount Clamp | 2 | 2 | 2 |
7 | 5029212-BLK | MX4 Saddle Base | 2 | 2 | 2 |
8 | 5034637 | 5/16-18 x 1.25 Flng Hex Bolt | 4 | 4 | 4 |
Ref. # | Part # | Description | 408 | 410 | 412 |
--- | --- | --- | --- | --- | --- |
9 | 5282569 | MX4 Boom Harness, 1-Way, Center | 1 | 1 | 1 |
9.1 | 5020576 | Hose, 1/2″ (2SP) x 26″ | 2 | 2 | 2 |
9.2 | 5051114 | Hose Clamp (1/2″) | 10 | 10 | 10 |
9.3 | 5002522 | QJ17560A Nozzle Body, 11003 AIXR Tip, 1/2″ HB Tee | 4 | 4 | 4 |
9.4 | 5020977 | Hose, 1/2″-1 Brd. x 18 1/2″ | 2 | 2 | 2 |
9.5 | 5020572 | Hose, 1/2″-1 Brd. x 10″ | 2 | 2 | 2 |
9.6 | 5086026 | Poly Hose Tee, 1/2″ HB | 1 | 1 | 1 |
10 | 5117342 | 5/16-18 x 0.50 PH Truss Head Screw | 8 | 10 | 12 |
11-A | 5282570 | MX4 Boom Harness, 2-Nozzle Wing, LH | 1 | — | — |
11-B | 5282572 | MX4 Boom Harness, 3-Nozzle Wing, LH | — | 1 | — |
11-C | 5282574 | MX4 Boom Harness, 4-Nozzle Wing, LH | — | — | 1 |
11.1 | 5002522 | QJ17560A Nozzle Body, 11003 AIXR Tip, 1/2″ HB Tee | 1 | 2 | 3 |
11.2 | 5002523 | QJ17560A Nozzle Body, 11003 AIXR Tip, 1/2″ HB (LH) | 1 | 1 | 1 |
11.3 | 5020977 | Hose, 1/2″-1 Brd. x 18 1/2″ | 1 | 2 | 3 |
11.4 | 5051114 | Hose Clamp (1/2″) | 2 | 4 | 6 |
12 | 5051114 | Hose Clamp (1/2″) | 3 | 3 | 3 |
13-A | 5282571 | MX4 Boom Harness, 2-Nozzle Wing, RH | 1 | — | – – – |
13-B | 5282573 | MX4 Boom Harness, 3-Nozzle Wing, RH | — | — | — |
13-C | 5282575 | MX4 Boom Harness, 4-Nozzle Wing, RH | — | — | 1 |
13.2 | 5002522 | QJ17560A Nozzle Body, 11003 AIXR Tip, 1/2″ KB Tee | 1 | 2 | 3 |
13.3 | 5002524 | QJ17560A Nozzle Body, 11003 AIXR Tip, 1/2″ HB (RH) | 1 | 1 | 1 |
13.4 | 5020977 | Hose, 1/2″-1 Brd. x 18 1/2″ | 1 | 2 | 3 |
13. | 5051114 | Hose Clamp (1/2″) | 2 | 4 | 6 |
14 | 5020973 | Hose, 1/2″-1Brd x 18 Ft. | 1 | 1 | 1 |
15 | 5002514 | Single 1/2″ Barb Dry Boom Nozzle Adaptor | 2 | 2 | 2 |
16 | 5282562-BLK | MX4 Boom, Wing Lock | – – – | 1 | 1 |
17 | 5006345 | 3/8-16 Flng Top-Lock Hex Nut | — | — | 4 |
18 | 5034485 | 3/8-16 x 2.00 Carriage Bolt | — | — | 4 |
19 | 5034639 | 5/16-18 x 1.75 Flng Hex Bolt (Full Thread) | – – – | 1 | 1 |
20 | 5101260 | 5/16″ x 1-3/4″ Lynch Pin | – – – | 1 | 1 |
FSBK-3025BL (5301289) Component Breakdown & Parts List
Ref. # | Part # | Description | Qty |
---|---|---|---|
1 | 5275260 | “Wet Boom” Assembly | 1 |
1.1 | 5275712 | Wet Boom Sub-Assembly | 1 |
1.1.1 | 5100316 | Boom Tube | 1 |
1.1.2 | 5275123 | Center Nozzle Assembly (Wet Boom) | 1 |
1.1.2.1 | 5274862 | Center Boomless Nozzle Cap w/Gasket | 1 |
1.1.2.2 | 5018329 | Center Spray Tip | 1 |
1.1.2.3 | 5088024 | Valve (On/Off) Knob w/Diaphragm | 1 |
1.1.2.3.1 | 5063255 | Diaphragm | 1 |
Ref. # | Part # | Description | Qty |
--- | --- | --- | --- |
1.1.3 | 5075016 | Rubber Grommet | 2 |
1.2 | 5275122 | End Nozzle Assembly (Wet Boom) | 2 |
1.2.1 | 5274861 | XT Spray Nozzle, Cap, & 0-Ring | 1 |
1.2.2 | 5088024 | Valve (On/Off) Knob w/Diaphragm | 1 |
1.2.2.1 | 5063255 | Diaphragm | 1 |
2 | 5034220 | Round U-Bolt, 5/16″-18 x 1 5/16″ x 1 3/4″ | 2 |
3 | 5006307 | 5/16-18nc Hex Flanged Whiz Nut Gr. 5 | 4 |
-
Check the spray pattern. Usually you can see the coverage better on a solid concrete surface, such as a driveway.
-
Approximate height: 33”
- The (3) nozzles are fixed at 17-1/2” spacing
- All (3) nozzles spraying at the same time will allow a maximum coverage of 36 feet
- The center nozzle will spray an 80” swath
- Each of the (3) nozzles has a shutoff valve, so you can shut off each nozzle individually. This may help in achieving the actual coverage needed for your application.
FSBK-3025BL (5301289) End Nozzle Assembly & Info
- First REMOVE O-Ring, Item 2 (#5072517) from the end nozzle body assembly.
- Start by sliding Item 4, 3, 2 onto the boom tube (Item 1) as shown, leaving about 1/2” to 3/4” between the end of the boom tube and Item 2. Make sure the “Long” portion of Item 3 is facing the nozzle end.
- Slide the (complete) end nozzle assembly onto the stainless steel boom tube, with somewhat of a “twisting” motion, so that the end face of the boom tube “butts” up against the surface face inside the nozzle body.
- Now push the “compression olive” (Item 3) against O-rin(Item 2) and slide (both) into the nozzle body opening firmly.
- Firmly tighten flynut (Item 4) onto threads of nozzle body
Repeat for other side.
NOTE: If water is shooting back on the boom tube, item 2 is not in the
correct placement.
BXT Series Boomless Boom Component Breakdown & Parts List
Ref. # | Part # | Description | Qty |
---|---|---|---|
1 | 5011313-BLK | Center Boom Tube, 1″ Square | 1 |
2 | 5046459 | Tube Cap, 1″ Square | 2 |
3 | 5101377 | Spring Steel Button Pin | 2 |
4 | 5034156 | 1/4-20 x 1.50 Hex Bolt | 2 |
5 | 5282464 | BXT Pivot Assembly, LH | 1 |
5.1 | 5070194-BLK | BXT Bracket, LH | 1 |
5. | 5034527 | 1/4-20 x 1.50 Carriage Bolt | 1 |
5.2 | 5006306 | 1/4-20 Serrated Flng Hex Nut | 1 |
5.3 | 5149210 | 1/4″ FNPT 90° Brass Elbow | 1 |
5.4 | 5010197 | Poly Elbow, 1/4″ MNPT x 1/2″ HB | 1 |
5.5 | 5002380 | QJ Diaphragm Check Valve 1/4 MNPT | 1 |
6 | 5282465 | BXT Pivot Assembly, RH | 1 |
6.1 | 5070195-BLK | BXT Bracket, RH | 1 |
6.2 | 5034527 | 1/4-20 x 1.50 Carriage Bolt | 1 |
6.3 | 5006306 | 1/4-20 Serrated Flng Hex Nut | 1 |
6.4 | 5149210 | 1/4″ FNPT 90° Brass Elbow | 1 |
6.5 | 5010197 | Poly Elbow, 1/4″ MNPT x 1/2″ HB | 1 |
6.6 | 5002380 | QJ Diaphragm Check Valve 1/4 MNPT | 1 |
7 | 5088026 | 5 Lobe Knob 1/4-20UNC | 2 |
8 | FC-XT015 | Hypro Boom X-Tender Spray Nozzle (Green) | 2 |
9 | 5006307 | 5/16-18 Serrated Flng Hex Nut | 4 |
10 | 5277923 | Nozzle Clamp, 1″ | 4 |
Ref. # | Part # | Description | Qty |
--- | --- | --- | --- |
11 | 5282466 | 4-Nozzle BXT Harness AIXR | 1 |
11.1 | 5281311 | Elbow Nozzle Assembly, 1/2″ | 2 |
11.1.1 | 5056065 | Nozzle Body – QJ – Elbow – 1/2″ | 1 |
11.1.2 | 5143543 | Nozzle Check Strainer, Blue (50 Mesh) | 1 |
11.1.3 | 5016157 | Seat Washer – EPDM – QJ Caps | 1 |
11.1.4 | 5018371 | Air-Induction XR Flat Spray Tip – AIXR11002VP | 1 |
11.1.5 | 5046219 | Quick Cap – Yellow | 1 |
11.2 | 5020569 | Hose, 1/2″-1 Brd. x 19 3/8″ | 2 |
11.3 | 5051114 | Hose Clamp (1/2″) | 8 |
11.4 | 5281313 | Tee Nozzle Assembly, 1/2″ | 2 |
11.4.1 | 5056067 | Nozzle Body – QJ – Tee – 1/2″ | 1 |
11.4.2 | 5143543 | Nozzle Check Strainer, Blue (50 Mesh) | 1 |
11.4.3 | 5016157 | Seat Washer – EPDM – QJ Caps | 1 |
11.4.4 | 5018371 | Air-Induction XR Flat Spray Tip – AIXR11002VP | 1 |
11.4.5 | 5046219 | Quick Cap – Yellow | 1 |
11.5 | 5020572 | Hose, 1/2″-1 Brd. x 10″ | 2 |
11.6 | 5086026 | Poly Hose Tee, 1/2″ HB | 1 |
12 | 5034159 | 5/16-18 x 1.3125 x 1.875 Square U-Bolt | 2 |
13 | 5020973 | Hose, 1/2″-1 Brd x 18′ | 1 |
14 | 5051114 | Hose Clamp (1/2″) | 6 |
Hamilton Boomless Assembly Component Breakdown & Parts List
Hamilton #10 Boomless Kit MC1-10HAM-KIT (5282538)
Ref. # | Part # | Description | Qty |
---|---|---|---|
1 | 5070259-BLK | MC 3-PT BXT Boom Bracket | 1 |
2 | 5046448 | Square Cap, Black (1 1/4″ Square Tube) | 1 |
3 | 5282537 | Hamilton #10 Boomless Assembly | 1 |
3.1 | 5034609 | 1/4-20 x 0.50 Flng Hex Bolt | 2 |
3.2 | 5095983-BLK | Boomless Nozzle Mount | 2 |
3.3 | 5006344 | 1/4-20 Flng Top-Lock Hex Nut | 4 |
3.4 | 5051174 | 1/2″ Wet Boom Clamp (2-Piece) | 1 |
3.5 | 5034615 | 1/4-20 x 2.00 Flng Hex Bolt (Full Thread) | 2 |
3.6 | 5088026 | 5 Lobe Knob 1/4-20UNC | 2 |
3.7 | 5034807 | 1/4-20 x 1.75 Carriage Bolt | 2 |
3.8 | 5282536 | Hamilton #10 Boomless Kit | 1 |
3.8.1 | 654101 | W.L. Hamilton #10 Boomless Nozzle | 1 |
3.8.2 | 5011258 | 1/2″ Pipe Nipple, 4″ Long, 304 SS | 1 |
3.8.3 | 5149158 | Poly Elbow, 1/2″ FNPT x 1/2″ Hose Barb | 1 |
4 | 5020099 | Hose, 3/8″-2 Brd. x 25 Ft. | 1 |
5 | HCO8 | Hose Clamp, 1/2″ | 2 |
BXT Boomless Nozzle Component Breakdown & Parts List
Ref. # | Part # | Description | Qty |
---|---|---|---|
1 | 5070259-BLK | MC 3-PT BXT Boom Bracket | 1 |
2 | 5046448 | Square Cap, Black (1 1/4″ Square Tube) | 1 |
3 | 5282521 | BXT Boomless Assembly | 1 |
3.1 | 5034609 | 1/4-20 x 0.50 Flng Hex Bolt | 2 |
3.2 | 5095983-BLK | Boomless Nozzle Mount | 2 |
3.3 | 5006344 | 1/4-20 Flng Top-Lock Hex Nut | 6 |
3.4 | 5051174 | 1/2″ Wet Boom Clamp (2-Piece) | 2 |
3.5 | 5034615 | 1/4-20 x 2.00 Flng Hex Bolt (Full Thread) | 4 |
3.6 | 5088026 | 5 Lobe Knob 1/4-20UNC | 2 |
3.7 | 5034807 | 1/4-20 x 1.75 Carriage Bolt | 2 |
3.8 | 5282520 | BXT Boomless Nozzle Assembly (LH) | 1 |
3.8.1 | FC-XT024 | Hypro Fast Cap Boom X-tender (Yellow) | 1 |
3.8.2 | 5002380 | QJ Diaphragm Check Valve 1/4 MNPT | 1 |
3.8.3 | 5041073 | Poly Reducing Bushing, 1/2″ MNPT x 1/4″ FNPT | 1 |
Ref. # | Part # | Description | Qty |
--- | --- | --- | --- |
3.8.4 | 5010236 | Poly Elbow, 1/2″ FNPT x 1/2″ FNPT | 1 |
3.8.5 | 5011258 | 1/2″ Pipe Nipple, 4″ Long, 304 SS | 1 |
3.8.6 | 5149158 | Poly Elbow, 1/2″ FNPT x 1/2″ Hose Barb | 1 |
3.9 | 5282519 | BXT Boomless Nozzle Assembly (RH) | 1 |
3.9.1 | FC-XT024 | Hypro Fast Cap Boom X-tender (Yellow) | 1 |
3.9.2 | 5002380 | QJ Diaphragm Check Valve 1/4 MNPT | 1 |
3.9.3 | 5041073 | Poly Reducing Bushing, 1/2″ MNPT x 1/4″ FNPT | 1 |
3.9.4 | 5010236 | Poly Elbow, 1/2″ FNPT x 1/2″ FNPT | 1 |
3.9.5 | 5011258 | 1/2″ Pipe Nipple, 4″ Long, 304 SS | 1 |
3.9.6 | 5149158 | Poly Elbow, 1/2″ FNPT x 1/2″ Hose Barb | 1 |
4 | 5020099 | Hose. 3/8″-2 Brd. x 25 Ft. | 1 |
5 | HCO8 | CLAMP, 1/2″ HOSE | 4 |
Handgun Kits Component Breakdown & Parts List
MC-PRO22-HG-KIT
MC 3-PT 22” Pro Series Handgun Kit
#5282518
- No Drip Shut Off
- Easy Pull Trigger Handle
- Chemical Resistant Construction
- 600 PSI, 8 GPM
- 38’ Horizontal Throw & 27’ Vertical Throw
Ref. # | Part # | Description | Qty |
---|---|---|---|
1 | 5163150 | 22″ HP Spray Gun with 3/8″ Hose Barb | 1 |
1.1 | 5163136 | High Pressure Aluminum Spray Gun 22″ | 1 |
1.2 | 5067130 | Poly Fitting, 1/2″ MNPT x 3/8″ HB | 1 |
2 | 5070257-BLU | Handgun & Hose Bracket | 1 |
3 | 5020099 | Hose, 3/8″-2 Brd. x 25 Ft. | 1 |
4 | HCO6 | Hose Clamp (3/8″) | 2 |
5 | 5075014 | Rubber Grommet (Black) | 2 |
6 | 5010206 | Poly Elbow, 3/4″ MNPT x 3/8″ HB | 1 |
7 | 5149213 | 3/4″ FNPT T5 Male Fitting w/EPDM 0-Ring | 1 |
To adjust the spray pattern, the nut needs to be adjusted (Ref. A). Spinning
it off, towards the lever, will make a cone pattern and spinning it on, away
from the lever, will make a stream. The lever (Ref. B), is the lock that can
be used to lock the lever when pulled, holding the valve open.
Squeezing the trigger, will release the lock.
Ref. # | Part # | Description | Qty |
---|---|---|---|
1 | 5273959 | Deluxe Pistol-Grip Handgun w/X-26 Tip | 1 |
1. | 5018331 | Brass Handgun Tip (X-26) | 1 |
2 | 5070257-BLU | HANDGUN & HOSE BRACKET | 1 |
3 | 5020099 | Hose, 3/8″-2 Brd. x 25 Ft. | 1 |
4 | HCO6 | CLAMP, 3/8″ HOSE | 2 |
5 | 5075014 | Rubber Grommet (Black) | 2 |
6 | 5010206 | Poly Elbow, 3/4″ MNPT x 3/8″ HB | 1 |
7 | 5149213 | 3/4″ FNPT T5 Male Fitting w/EPDM 0-Ring | 1 |
Valve Assembly Component Breakdown & Parts List
ARAG
NPT+1
Two Sec Valve Assembly
5282495
Ref. # | Part # | Description | Qty |
---|---|---|---|
1 | 219150 | T5 Male Plug Fitting | 1 |
1.1 | 5072548 | T5 0-Ring Viton | 1 |
2 | 463T001.010 | Single 463T Body Bare | 1 |
2.1 | 5069006 | T3 Fork D.3 Dist, 29 | 2 |
2.2 | 5069007 | T5 Fork D.3 Dist, 42 | 1 |
3 | 1091320 | T3 Male x 3/4″ Hose Barb Straight | 1 |
3.1 | 5072545 | T3 0-Ring EPDM | 1 |
4 | 239133N | 3/4″ FNPT x T3 Male Fitting | 1 |
4.1 | 5072545 | T3 0-Ring EPDM | 1 |
5 | 5072548 | T5 0-Ring Viton | 1 |
6 | 5143560 | 1-Sec. Manual Valve T5XT3 | 1 |
6.1 | 5069006 | T3 Fork D.3 Dist, 29 | 2 |
6.2 | 5069007 | T5 Fork D.3 Dist, 42 | 1 |
7 | 1091313 | T3 Male x 1/2″ Hose Barb Straight | 1 |
7.1 | 5072545 | T3 0-Ring EPDM | 1 |
8 | 219050 | T5 Female Blank Cap | 1 |
8.1 | Sweepl | T5 Fork D.3 Dist, 42 | 1 |
Manual On/Off Section Valve Component Breakdown & Parts List
ARAG 1-Sec Valve Assembly w/1/2” HB
#5282497
|
---|---
Ref. #| Part #| Description| Qty
---|---|---|---
1| 5143560| 1-Sec. Manual Valve T5XT3 (Yellow Lever)| 1
2| 1091313| T3 Male x 1/2″ Hose Barb Straight| 1
2.1| 5072545| T3 0-Ring EPDM| 1
Handgun Valve Component Breakdown & Parts List
ARAG 1-Sec Valve Assembly w/3/8” HB
#5282496
|
---|---
Ref. #| Part #| Description| Qty
---|---|---|---
1| 5143560| 1-Sec. Manual Valve T5XT3| 1
2| 1091310| T3 Male x 3/8″ Hose Barb Straight| 1
2.1| 5072545| T3 0-Ring EPDM| 1
RP-600 Series 6-Roller Pump Component Breakdown & Parts List
Ref. # | Part # | Description | Qty |
---|---|---|---|
1 | RP-600C-BLU | 6-Roller Cast Iron Pump | 1 |
2 | 5010209 | Poly Elbow, 3/4″ MNPT x 3/4″ HB | 1 |
3 | 5010210 | Poly Elbow, 3/4″ MNPT x 1″ HB | 1 |
4 | 5057145 | Quick Coupler (5/8″) | 1 |
5 | 5034634 | 5/16-18 x 0.625 Flng Hex Bolt | 2 |
6 | 5016026 | 5/16 Lock Washer | 2 |
7 | 5271623 | Torque Bar & Chain Assembly | 1 |
7. | 5038513-BLK | Torque Bracket | 1 |
7. | 5082006 | “5” Hook | 1 |
7. | 5049017 | Torque Chain, 24″ | 1 |
7. | 5094039 | 1/4″ Rapid/Quick Link | 1 |
RP-600C-B-PUMP-KIT
#5282526
Imperial | 0 PSI | 50 PSI | 100 PSI | 150 PSI | 200 PSI | 250 PSI | 300PSI |
---|---|---|---|---|---|---|---|
GPM | HP | GPM | HP | GPM | HP | GPM | HP |
540 RPM | 9.7 | 0.80 | 8.0 | 0.38 | 7.2 | 0.68 | 6.6 |
4.3 | 1.91 | ||||||
1000 RPM | 18.2 | 0.20 | 16.5 | 0.71 | 15.4 | 1.26 | 14.7 |
13. | 3.47 | ||||||
1200 RPM | 21.8 | 0.30 | 20.1 | 0.90 | 19.1 | 1.51 | 18.2 |
3.48 | 15.7 | 4.17 |
Ref. # | Part # | Description | Qty |
---|---|---|---|
1 | ♦♦ | Dust Cap, Cover | 1 |
2 | 14859 | Bearing, Sealed | 2 |
3 | 14858 | Seal, FKM | 2 |
4 | GE-60-SS | Cap Screw, 5/16″ x 3/4″ | 4 |
5 | ♦♦ | End Plate, Cast Iron | 1 |
6 | 14861 | 0-Ring, Body Seal | 1 |
7 | ♦♦ | Body, Cast Iron | 1 |
8 | ♦♦ | Dust Cap, Body | 1 |
9 | ♦♦ | Rotor, Cast Iron (Includes #10) | 1 |
10 | 5117100 | Cap Screw, 5/16″nc x 5/16″ Allen Head | 1 |
11 ** | – – – | Roller | 6 |
12 | ** | Shaft, SS | 1 |
6500XL Series 6-Roller Pump Component Breakdown & Parts List
6500XL-PUMPKIT
5276977
Ref. # | Part # | Description | Qty |
---|---|---|---|
1 | 5273024 | 6-Roller Pump (6500XL) | 1 |
2 | 5057145 | Quick Coupler (5/8″) | 1 |
3 | 5010209 | Poly Elbow, 3/4″ MNPT x 3/4″ HB | 1 |
4 | 5010210 | Poly Elbow, 3/4″ MNPT x 1″ HB | 1 |
5 | 5016026 | Lockwasher, 5/16″ | 2 |
6 | 5034634 | H.H.C.S. Flanged 5/16″-18nc x 5/8″ Long | 2 |
7 | 5271623 | Torque Bar & Chain Assembly | 1 |
7.1 | 5038513-BLK | Torque Bracket | 1 |
7.2 | 5082006 | “S” Hook | 1 |
7.3 | 5049017 | Torque Chain, 24″ | 1 |
7.4 | 5094039 | 1/4″ Rapid/Quick Link | 1 |
Imperial | 0 PSI | 50 PSI | 100 PSI |
--- | --- | --- | --- |
GPM | HP | GPM | HP |
540 RPM | 9.7 | 0.1 | 8.0 |
1000 RPM | 18.2 | 0.2 | 16.5 |
12.7 | 3.5 | ||
1200 RPM | 21.8 | 0.3 | 20.1 |
15.7 | 4.2 |
Silver Cast
6-Roller Pump Assembly
5273024 (Hypro 6500XL)
-
- Available only in Repair Parts Kit #7771795 (3430-0380)
(Super Rollers are also included in Repair Parts Kit)
♦ ♦ Only Available in Complete Assembly
- Available only in Repair Parts Kit #7771795 (3430-0380)
Ref. # | Part # | Description | Qty |
---|---|---|---|
1 | 5017481 | Bearing Cover | 1 |
2 | 5031113 | Ball Bearing (Sealed) | 2 |
3* | 5110052 | Seal (Viton) | 2 |
4 | ♦♦ | End Plate (SilverCast) w/Seal | 1 |
5 | 5034038 | H.H.C.S. 5/16″-18nc x 3/4″ Long | 4 |
6* | 5072056 | 0-Ring Gasket | 1 |
7 | ♦♦ | Rotor/Shaft Assembly (SilverCast) | 1 |
8* | 5112030 | Super Roller (Standard) | 6 |
9 | ♦♦ | Body w/Seal (SilverCast) | 1 |
10 | 5017480 | Shaft Bearing Cover | 1 |
MC-Electric Control Conversion Kits
MC-1E-CONVRSN-KIT (5282543)
MC-2E-CONVRSN-KIT (5282544)
MC-3E-CONVRSN-KIT (5282545)
Conversion from Manual Controls to Electric Boom Section Control:
- Remove the fork wire clip below the manual lever
- Lift the manual lever out of the manifold
- Insert the electric motor with electric connection facing forward making sure the alignment grooves matchup and motor is down completely
- Reinstall the fork wire clip now holding the electric motor in place
- Connect the 3-tab electric plugs to the electric motor(s) using the gasket and screw included with the wire harness
- Mount the control box in the tractor
- Plug power cord into 12VDC convenience plug. If tractor does not have one, install the socket 25A in the tractor according to the diagram on page 7
- Connect wiring harness and power cord to control box
- Test control box making sure all valve(s) function when the toggle switches and master switch are actuated.
Ref. # | Item 44 | Description | Qty. |
---|---|---|---|
1 | 910320 | Control Box, Up to 3 Section | 1 |
2 | 901208. | Power Cord | 1 |
3 | BL-400504 | Socket 25A, Power Plug | 1 |
4 | 919049-5.0 | 16′ Extension Cable for 910320 | 1 |
5 | 770252 | End Cable— 3 valve | 1 |
6 | 863T001 | 863T Electric Valve | 1 |
Warranty Info
LIMITED WARRANTY FOR NEW Cimarron EQUIPMENT
WHO MAY USE THIS LIMITED WARRANTY. This limited warranty (the “Limited
Warranty”) is provided by Fimco, Inc. (“Cimarron Equipment“) to the original
purchaser (“you”) of the Equipment (as defined below) from Cimarron Equipment
or one of Cimarron Equipment’s authorized dealers.
This Limited Warranty does not apply to any subsequent owner or other
transferee of the Equipment. THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL
RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
WHAT THIS LIMITED WARRANTY COVERS AND FOR HOW LONG. Cimarron Equipment
warrants that any new Equipment will be free from defects in material and
workmanship for a period of one (1) year (homeowner), 90 days (commercial
user), after delivery of the Equipment to you (the “Warranty Period”). The
Warranty Period is not extended if Cimarron Equipment repairs or replaces the
Equipment.
WHAT IS NOT COVERED BY THIS LIMITED WARRANTY. This Limited Warranty does not
apply to: (1) used Equipment; (2) any Equipment that has been altered,
changed, repaired or treated since its delivery to you, other than by Cimarron
Equipment or its authorized dealers; (3) damage or depreciation due to normal
wear and tear; (4) defects or damage due to failure to follow Cimarron
Equipment’s operator’s manual, specifications or other written instructions,
or improper storage, operation, maintenance, application or installation of
parts; (5) defects or damage due to mis-use, accident or neglect, “acts of
God” or other events beyond Cimarron Equipment’s reasonable control; (6)
accessories, attachments, tools or parts that were not manufactured by
Cimarron Equipment, whether or not sold or operated with the Equipment; or
(7) rubber parts, such as tires, hoses and grommets.
HOW TO OBTAIN WARRANTY SERVICE. To obtain warranty service under this Limited
Warranty, you must (1) provide written notice to Cimarron Equipment of the
defect during the Warranty Period and within thirty (30) days after the defect
becomes apparent or the repair becomes neces-sary, at the following address:
Cimarron Equipment, 1000 Fimco Lane, North Sioux City, SD 57049; and (2) make
the Equipment available to Cimarron Equipment or an authorized dealer within a
reasonable period of time. For more information about this Limited Warranty,
please call: 800-274-1025
WHAT REMEDIES ARE AVAILABLE UNDER THIS LIMITED WARRANTY. If the conditions set
forth above are fulfilled and the Equipment or any part thereof is found to be
defective, Cimarron Equipment shall, at its own cost, and at its option,
either repair or replace the defective Equipment or part. Cimarron Equipment
will pay for shipping and handling fees to return the repaired or replacement
Equipment or part to you.
LIMITATION OF IMPLIED WARRANTIES AND OTHER REMEDIES. THE REMEDIES DESCRIBED
ABOVE ARE YOUR SOLE AND EXCLUSIVE REMEDIES, AND Cimarron EQUIPMENT’S SOLE
LIABILITY, FOR ANY BREACH OF THIS LIMITED WARRANTY. TO THE EXTENT APPLICABLE,
ANY IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL BE LIMITED IN
DURATION TO THE WARRANTY PERIOD, AND THE REMEDIES AVAILABLE FOR BREACH THEREOF
SHALL BE LIMITED TO THE REMEDIES AVAILABLE UNDER THIS EXPRESS LIMITED
WARRANTY. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY
LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. IN NO EVENT SHALL
Cimarron EQUIPMENT’S LIABILITY UNDER THIS LIMITED WARRANTY EXCEED THE ACTUAL
AMOUNT PAID BY YOU FOR THE DEFECTIVE EQUIPMENT, NOR SHALL Cimarron EQUIPMENT
BE LIABLE, UNDER ANY CIRCUMSTANCES, FOR ANY CONSEQUENTIAL, INCIDENTAL, SPECIAL
OR PUNITIVE DAMAGES OR LOSSES, WHETHER DIRECT OR INDIRECT. SOME STATES DO NOT
ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO
THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>