SUNWAYI SC43-E Digital Wireless Solar Car Rear-view Camera Kit User Manual

SC43-E Digital Wireless Solar Car Rear-view Camera Kit
User Manual Solar Wireless Rearview Camera
100% DY, intalls in minutes.
User Manual

SC43-E Digital Wireless Solar Car Rear-view Camera Kit

INTRODUCTION

Welcome
Thanks for your choosing SC43-E product, which provides value and quality. Please read this User Manual carefully before using the product.
Rearview Camera with Solar Panel can display image behind the vehicle and can be used when backing up or any time you want to view behind the vehicle (even while your vehicle is in park).
Notice:
*Due to product upgrades or technical updates, the instruction manual may sometimes be changed in need. The manufacturer reserves the right to modify and update product specifications. without prior notice.
SE43-E, suitable for passenger cars, conditionally suitable for other relative vehicle, in Europe countries.

COMPONENTS

Scope of delivery / parts.

GETTING STARTED

Remove the whole Wireless Solar Car Camera SC43-E packing or assembly and make sure all components are included
Charge the camera’s battery
(The input voltage to the camera battery must be DC 5V when charging.
Otherwise the camera will be damaged.)

1. Connect the supplied USB to DC cord to the Ø5mm DC port of the camera
2. Plug the USB cable into any standard USB charger with an output rating of 1000mA or higher.
3. Charge 6 to 8 hours.

During the whole DC charging, the red indicator light will keep on. It will turn off when finishing the charging

• When the DC charging s done for a period of time, you can vibrate the camera and immodiately fouch the Touch-Sensor on the monitor o see the increase in charging. The baltery capacily icon on the screen shows the actual stalus of the camerals builln baftery power.
  Under normal use, the camera maintains a charge with exposure to sunlight. A battery status indicator is provided on the monitor when the camera is in use.
  If you’re storing your car in a garage ( or not exposing the camera to sunlight on a regular basis) for more than three month, you may need to recharge it via the DC charging port.

Check the wireless function

1. Shake the camera in the air.
2. Touch the Touch-Sensor quickly and check the image after the monitor is powered.

Note:
Camera has to be waken up from sleeping status by little vibtation.
*In the process of use, there is wireless interference from outside.
If no connection normally, the device will shut off automatically 10 seconds later. Then please touch the Touch-Sensor to turn it on.

License Plate Holder Installation

1. Installation method with license plate holder
   

2. Insert the license plate holder into the groove of the camera holder.

3. Use a screwdriver to screw the license plate holder and solar camera together to the rear of the car.

4. Loosen the bilateral cover strip of the license plate holder and insert the license plate.
   

5. Press the cover strips on both sides of the license plate frame to complete the installation.

6. Installation method without license plate holder
   (This installation method is suitable for license plates with holes)

7. Align the license plate directly at the hole in the camera holder backboard

8. Pass the screws through the license plate and camera holder backboard, and tighten the Screws to the rear of the car with a screwdriver.

MONITOR MOUNT

1. Monitor pedestal could be attached to vent, stand, or windshield as your requirements.
   There are 3 kinds of mounting brackets accordingly.
   

2. How to mount the brackets:

3. If using the factory default stand mount Stick on the dash board: Choose and clean a right place on the dash board, tear the paper of the monitor stand sticky tape, put and press tight the stand mount on the dash board.

4. If using the suction cup mount:
   Use suction cup mount to replace the default stand via screwdriver. Choose a right place on the windshield, and mount the suction cup mount on the windshield. With the suction lever in the released position, press the suction cup against the windshield. Press the suction ever toward the suction cup to lock the mount. To adjust the angle of monitor, loosen the collar on the ball joint, tighten in the desired position again.

5. The monitor can be mounted on the air outlet of the air conditioner in the car, allowing drivers to share the mobile phone bracket, and can avoid traffic violations (some country traffic laws do not allow the windshield or the center console to be installed anything to block the driver’s view sight). Please follow the steps:

6. Make sure the cross position of the, threaded base is correctly inserted into the cross groove of the monitor

7. Use L-shaped screwdriver to tighten the screws

8. Insert the ball into the nut

9. Press the vent mount ball inside the threaded base forcely

10. Rotate the nut and tighten it clockwise

11. By ifting up and down, the clamp can clamp or loosen the vent

12. Connect the monitor and car ignition lighter hole with power cord.

Camera Angle Adjustment

1. Please vibrate the camera, power the monitor, touch the Touch-Sensor on the monitor o show the rear image situation of car, then adjust the camera angle accordingly to the most suitable position.
ADJUSTABLE ANGLE FOR FLEXIBILITY………… 80°

When rotating the camera
Please hold the license plate holder with one hand, and rotate up or down the camera with the other hand to make the best Angle.
2. Parking Guideline Position Adjustment
The parking guideline position can be adjusted up or down, 1o mark the image area more realistic .There are 5 levels for choice.
For detailed operation methods plase refar to page P14.

OPERATION

Using the device SC43-E

1. Switch the DC power port with car ignition, the monitor will start work accordingly after touching the Touch-Sensor, the video signal will be sent from camera and will be displayed on the monitor.
2. If you want to see the backup image when driving your car, just touch the Touch-Sensor on the top of monitor.
3. When the vehicle is shut off, power is removed from the monitor and the monitor will shut off automatically, and the camera will stop work.

Note:

If you want the Rearview Camera SC43-E to keep working after the setting time of image-display(for example, you cannot finish reversing your vehicle during the first setting time), you have to touch the Touch-Sensor once again
After you have been staying inside vehicle quietly (eg. sleeping) with vehicle engine stopping, you want {o see the backup image but only put your vehicle key on the ACC-ON position (no starting the engine), there is no image on the monitor after touching the Touch-Sensor. So you have to give the vehicle a light vibration (such as re-open and shut car door, or tap somewhere lightly), then touch the Touch-Sensor to start work.

BUTTON & SETTING

Function of the monitor buttons

1. Middle button——[MENU/OK]:
   Short Press to enter monitor menu setting.
   Long Press (press and hold for 3 seconds) to confirm the chosen item in the menu setting interface.

2. + Button———–[ADD] Short Press to change/add parameter value at the menu setting interface.

3. – Button————[DEC}
   Short Press to change/decrease parameter value at the menu setting interface.

While the monitor is showing the rearview image again, short press [MENU/OK] to enter the main menu interface, select the *Image Mirror” icon and long press [MENU/OK], to set upwards or downwards image. After setting, short press it twice again continuously to exit the setting.
Itis best to have a video image displayed when making this selection (hort Press means press and hold 1 second, and Long Press means 3 seconds).Only Short Press – button [DEC] to switch the Parking guide Lines display modes (Display or No display)! Menu Operations:
1. Main Menu
While the monitor is showing the rear image, short press the middle button [MENUJ/OK] to enter the main menu interface, and 5 options are available (Pairing, Image Parameters, Image Mirror, Parking Guideline Adjustment, Time Setting)

| | | | |
---|---|---|---|---|---
Meaning| Pairing| Image Paramete| Image Mirror| Parking Guideline Position Adjustment| Time Setting
Operating| Default setting, no need to operate again.| To adjust Brightness Contrast, Color. Operation details as Image Parameter info.| Set Upwards/Downwards or Original/Mirror Image. Operation details as Image Mirror contents.| The parking guidelines can be adjusted up and down as needed. Operation details as Parking Guideline Position Adjust info.| Select”Time setting” and long press [Menu] key, press [ADD] or [DEC] key to select working time.

2. Image Parameter
While the monitor is showing the rear image, short press the middle button [MENU/OK] to enter the main menu interface. From the 3 options. Select Image Parameter, long press the [MENU/OK] button again, 3 Images(Brightness/ Contrast/ Color) setting interface are shown bellow: 1) Brightness setting
Select Brightness icon, press [+ADD] or [- DEC] button to adjust the brightness as shown bellow. 2) Contract setting
Select Contract icon, press [+ADD] or [- DEC] button to adjust the contract as shown bellow: 3) Color setting
Select Color icon, press [+ADD] or [- DEC] button to adjust the color as ‘shown bellow: 3. Image Mirror
Select the Image Mirror” icon and fong press the midde button [MENUJOK) o enter the mirror setting interface, short press [+ADD) or [- DEC] button, to set rightwards or leftwards image. After setting, short press [MENU/OK] twice continuously to exit the setting, the image setting will be saved for future use.
4. Parking Guideline Position Adjustment
Select the Parking Guide Position Adjustment” icon, then long press the middle bution [MENU / OK] to enter the setting interface, short press the [+ADD] or [- DEC] button to choose the most suitable one from 5 levels, then short press [MENU / OK] twice continuously to exit the seting.

INTERFACE ICON & Meaning

When the buil-n batery power is going to be lower enough because of using up. you have to charge the battery by DC fo USB cord. Otherwise, the camera wil ot work, and the montor cannot connect it.

INFORMATION

Battery Icon is on the top right comer of the screen, indicates the relative capacity of the built-in lthium battery of the camera when a video image is present.
Signal strength of the received image is on the top left corner when a video image is present.
Red Indicator Light
When the monitor is powered on and sl stay standby mode, the Red indicator Light doesn’t work. When touching Touch-Sensor, the Light will blink quickly. When the monitor works, the light will extinguish.
Wireless Camera
The Camera & Video transmitter are built-inside the SC43-E device, and is equipped with the buit-in rechargeable lithium battery, which is connected with the solar panel.
When the monitor is turned on, work command is sent to the camera, upon receive this signal, the camera will work from standby mode at once, and send image video to the monitor for the setting time.
DC to USB charging cable is provided to charge the battery initially prior to mounting on your vehicle, as well as to recharge if needed.

SPECIFICATION

CAMERA
View Angle: Horizontal Angle 135°
4 pes solar Panels for 1.5W charging power
Conversion rate of solar energy: 23%
Max. Current: 300mA
Sleeping Current: <0.06mA
Image Quality: Max 30 fps
Camera Waterproof: IP 67
Battery Capacity: 2600mAh (5200mAh for choice).
TRANSMITTER
Frequency: 2400 ~ 2485.5 MHz
Effective Transmission Distance 57.5ft (17.5m) Max.
(Installed in vehicles for test)
Working Temperature: 14°~ 140°F (-10°~ 60°C )
MONITOR
LCD Display Screen Size: 4.3 inches
Power Cord Fuse: 3A
Operation Current: <150mA
Effective Pixels: 480×272
The Setting Time of Image-Display:
30 seconds, 45 seconds (Default) or 60 seconds for choice.

TROUBLE SHOOTING

If the monitor doesn’t turn on when power is applied:

1. Check to make sure the power source is active (if your cigarette lighter is switched with vehicle ignition, your monitor will only work when the engine is running or the key in the ON position).
2. Check to make sure the fuse and power cord are in working order.

If the monitor doesn’t display images within a few seconds after touching the starting button:

1. The battery in the camera may be depleted and require recharging.
2. In the process of use, there is wireless interference from outside. so if you can’t turn on the camera over 10 seconds after touching, please touch the Touch-Sensor again to tur it on
3. If cannot display image after the two methods speaking above, please try re-pairing Shortly press MENU key, long press MENU key to confirm the pairing state when it is turned on. Under normal circumstances, the pairing will take about 5 seconds, and the wireless signal will automatically reconnect, the monitor will isplay the rear image accordingly.

If the video image is poor:
Check that the camera lens is clean from road grime, snow, or ice.
If the video image does not last the setting time:
Recharge the camera battery.
If no image after touching Touch-Sensor in quiet environment (no vibration at all) , such as testing SC43-E in office or laboratory.
Vibrate the camera, touch the powered Monitor Touch-Sensor quickly (not over 3 minutes from vibration) to wake up the sleeping camera make it enter standby status.

• Under the actual situation of installation, test, and use in car, the environment i different totally. Little vibration must happen when open door, people touching the vehicle, even the engine work So the camera will stay at standby status.
  If the battery capacity icon on the monitor shows that the camera’s battery is low,
  Check if the camera solar panels are covered with mud, water, dirt, etc, Please use soft cloth moistened with a neutral detergent solution to remove dust or stains, so as not to affect the solar power generation efficiency.

CARE & MAINTENANCE

Cleaning
Do not use solvents or chemical materials to clean or wipe SC43-E camera (including the lens and all solar panels)
If necessary, use a soft cloth moistened with a neutral detergent solution to remove dust or stains. Please clean the dirt or stains of the solar panel.
Fuse Replacement

1. Turn the cap on the top of the power plug counterclockwise (no tools needed).
2. Remove the cap, center pin and fuse.
3. Replace the fuse with a new 3-am fuse.
4. Replace the center pin and cap. Turn the cap clockwise.

Disposal
SC43-E product packing is designed to provide years of service
It should be recycled or safely disposed of at a local recycling center.

DISCLAIMER

SC43-E Solar Wireless Rearview Camera is intended to assist responsible driver, but it doesn’t relieve a driver from full responsibility for operation of the vehicle.
It is the driver’s sole responsibility to avoid contact with any objects, animals, especially persons. By installing and/ or using SCA3-E Solar Wireless Rearview Camera, you agree that you are solely responsible for the operation of your vehicle, the SC43-E supplier is not responsible for any property damage, personal injury, or loss of life that may result from the operation of your vehicle.
Note:
*Some EU Countries may have regulations or laws that restrict the use of anything that might impair the clear view of a license plate. Check local laws for explanation

Warranty:
BE SURE TO KEEP A COPY OF YOUR SALES RECEIPT! STANDARD WARRANTY
Supperlier warranty that your NEW Product is free of defects of workmanship and materials. If there is a defect or malfunction of this product, Supperlier will repair it free of charge as follows
PARTS: New or comparable rebuilt parts in exchange for defective parts for ONE YEAR from date of customer purchase.
LABOR: Supperlier provides labor warranty for (90) ninty days from date of end-user purchase. At completion of the repair, the consumer will be responsible for the cost for any parts or services no longer covered under the warranty.

WARRANTY INFO

This warranty does not apply to persons who purchased this product second-hand or used.
This warranty does not include adjustments, parts and/or repairs required by circumstances beyond the control of Supperlier,  including but not limited to fire or other casualty, accident, neglect, abuse, misuse, abnormal use o battery leakage damages.
THERE ARE NO OTHER EXPRESSED WARRANTIES EXCEPT AS STATED HEREIN. AFTER THE PERIOD OF EXPRESSED WARRANTY SET FORTH HEREIN, THERE ARE NO EXPRESSED OR IMPLIED WARRANTIES AND THOSE EXCLUDED INCLUDE THOSE OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE.
Supperlier shall NOT be held liable for CONSEQUENTIAL DAMAGES resulting from any failure,defect or malfunction of this product. Some Regions do not allow limitations on how long an implied warranty lasts and some Regions do not allow the exclusion or limitation of incidental or consequential damages, 50 the above limitations may not apply to you.
WARRANTY PROCEDURES
TO OBTAIN SERVICE UNDER THE TERMS OF THIS WARRANTY:
Please do the following:
1. Send a copy of your original sales receipt showing original purchase date, along with your mailing and shipping addresses, the model name of the product and a note describing the nature of the problem and a note describing the nature of the problem to:

SUPPORT

PRODUCT SUPPORT HOTLINE:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>