SUNWAYI WSE Solar Wireless Rearview Camera User Manual

WSE Solar Wireless Rearview Camera
User Manual

WSE Solar Wireless Rearview Camera

NTRODUCTION

Welcome
Thanks for your choosing SC43-E product, which provides value and quality. Please read this User Manual carefully before using the product.
Rearview Camera with Solar Panel can display image behind the vehicle and can be used when backing up or any time you want to view behind the vehicle (even while your vehicle is in park).
Notice:
*Due to product upgrades or technical updates, the instruction manual may sometimes be changed in need. The manufacturer reserves the right to modify and update product specifications. without prior notice.
SE43-E, suitable for passenger cars, conditionally suitable for other relative vehicle, in Europe countries.

COMPONENTS

1. European License Plate Holder with camera .

2. 

3. 4.3 inch monitor

4. Additional Mounts of Monitor

5. Ignition connect cable of Monitor

6. DC charging cord

7. Install Screws

8. Screwdriver

GETTING STARTED

Remove the whole Wireless Solar Car Camera SC43-E packing or assembly and make sure all components are included

Change the camera with lcense plate holder

1. Connect the supplied USB to DC cord to the Ø5mm DC port of the camera
2. Plug the USB cable into any standard USB charger with an output rating of 1000mA or higher.
3. Charge 6 to 8 hours.

During the whole DC charging, the red indicator light will keep on. It will turn off when finishing the charging

• When the DC charging s done for a period of time, you can vibrate the camera and immodiately fouch the Touch-Sensor on the monitor o see the increase in charging. The baltery capacily icon on the screen shows the actual stalus of the camerals builln baftery power.
  Under normal use, the camera maintains a charge with exposure to sunlight. A battery status indicator is provided on the monitor when the camera is in use.
  If you’re storing your car in a garage ( or not exposing the camera to sunlight on a regular basis) for more than three month, you may need to recharge it via the DC charging port.

Check the wireless function

1. Shake the camera in the air.
2. Touch the Touch-Sensor quickly and check the image after the monitor is powered.

Note:
Camera has to be waken up from sleeping status by little vibtation.
*In the process of use, there is wireless interference from outside.
If no connection normally, the device will shut off automatically 10 seconds later. Then please touch the Touch-Sensor to turn it on.

License Plate Holder Installation

1. Remove the cover strip from the license plate holder
   First remove the middle part of the cover strip, then remove the two sides of the cover strip
   

2. Install the license plate holder on the car using self-tapping screws, then tighten the screws via screwdriver
   

3. Insert license plate into the holder, frame the license plate through the small bezels basically
   

4. Insert the top cover strip’s clips into the relative holes of the license plate holder then press tight First press both ends of the cover plate. then press in the middle.

MONITOR MOUNT

1. Monitor pedestal could be attached to vent, stand, or windshield as your requirements.
   There are 3 kinds of mounting brackets accordingly.
   

2. How to mount the brackets:
   

3. If using the factory default stand mount Stick on the dash board: Choose and clean a right place on the dash board, tear the paper of the monitor stand sticky tape, put and press tight the stand mount on the dash board.

4. If using the suction cup mount:
   Use suction cup mount to replace the default stand via screwdriver. Choose a right place on the windshield, and mount the suction cup mount on the windshield. With the suction lever in the released position, press the suction cup against the windshield. Press the suction ever toward the suction cup to lock the mount. To adjust the angle of monitor, loosen the collar on the ball joint, tighten in the desired position again.

5. The monitor can be mounted on the air outlet of the air conditioner in the car, allowing drivers to share the mobile phone bracket, and can avoid traffic violations (some country traffic laws do not allow the windshield or the center console to be installed anything to block the driver’s view sight). Please follow the steps:

6. Make sure the cross position of the, threaded base is correctly inserted into the cross groove of the monitor

7. Use L-shaped screwdriver to tighten the screws

8. Insert the ball into the nut

9. Press the vent mount ball inside the threaded base forcely

10. Rotate the nut and tighten it clockwise

11. By ifting up and down, the clamp can clamp or loosen the vent

12. Connect the monitor and car ignition lighter hole with power cord.

Camera Angle Adjustment

1. Please vibrate the camera, power the monitor, touch the Touch-Sensor on the monitor o show the rear image situation of car, then adjust the camera angle accordingly to the most suitable position.
   ADJUSTABLE ANGLE FOR FLEXIBILITY………… 114° When rotating the camera
   Please hold the license plate holder with one hand, and rotate up or down the camera with the other hand to make the best Angle.

2. Parking Guideline Position Adjustment
   The parking guideline position can be adjusted up or down, 1o mark the image area more realistic .There are 5 levels for choice.
   For detailed operation methods plase refar to page P11.

OPERATION

Using the device Rearview camera

1. Switch the DC power port with car ignition, the monitor will start work accordingly after touching the Touch-Sensor, the video signal will be sent from camera and will be displayed on the monitor.
   

2. If you want to see the backup image when driving your car, just touch the Touch-Sensor on the top of monitor.

3. When the vehicle is shut off, power is removed from the monitor and the monitor will shut off automatically, and the camera will stop work.

Note:

If you want the Rearview Camera SC43-E to keep working after the setting time of image-display(for example, you cannot finish reversing your vehicle during the first setting time), you have to touch the Touch-switch once again.
After you have been staying inside vehicle quietly (eg. sleeping) with vehicle engine stopping, you want {o see the backup image but only put your vehicle key on the ACC-ON position (no starting the engine), there is no image on the monitor after touching the Touch-switch. So you have to give the vehicle a light vibration (such as re-open and shut car door, or tap somewhere lightly), then touch the Touch-switch to start work.

BUTTON & SETTING

Function of the monitor buttons

1. The Middle button——[MENU/OK]:
   Short Press to enter monitor menu setting.
   Long Press (press and hold for 3 seconds) to confirm the chosen item in the menu setting interface.

2. The up Button———–[ADD] Short Press to change/add parameter value at the menu setting interface.

3. The  down Button————[DEC}
   Short Press to change/decrease parameter value at the menu setting interface.

While the monitor is showing the rearview image again, short press [MENU/OK] to enter the main menu interface, select the *Image Mirror” icon and long press [MENU/OK], to set upwards or downwards image. After setting, short press it twice again continuously to exit the setting.
Itis best to have a video image displayed when making this selection (hort Press means press and hold 1 second, and Long Press means 3 seconds).Only Short Press – button [DEC] to switch the Parking guide Lines display modes (Display or No display)! Menu Operations:

1. Main Menu
   While the monitor is showing the rear image, short press the middle button [MENUJ/OK] to enter the main menu interface, and 5 options are available (Pairing, Image Parameters, Image Mirror, Parking Guideline Adjustment, Time Setting)
   | | | | |
   ---|---|---|---|---|---
   Meaning| Pairing| Image Paramete| Image Mirror| Parking Guideline Position Adjustment| Time Setting
   Operating| Default setting, no need to operate again.| To adjust Brightness Contrast, Color. Operation details as Image Parameter info.| Set Upwards/Downwards or Original/Mirror Image. Operation details as Image Mirror contents.| The parking guidelines can be adjusted up and down as needed. Operation details as Parking Guideline Position Adjust info.| Select”Time setting” and long press [Menu] key, press [ADD] or [DEC] key to select working time.

2. Image Parameter
   While the monitor is showing the rear image, short press the middle button [MENU/OK] to enter the main menu interface. From the 3 options. Select Image Parameter, long press the [MENU/OK] button again, 3 Images(Brightness/ Contrast/ Color) setting interface are shown bellow:

3. Brightness setting
   Select Brightness icon, press [+ADD] or [- DEC] button to adjust the brightness as shown bellow.

4. Contract setting
   Select Contract icon, press [+ADD] or [- DEC] button to adjust the contract as shown bellow:

5. Color setting
   Select Color icon, press [+ADD] or [- DEC] button to adjust the color as ‘shown bellow:

6. Image Mirror
   Select the *Image Mirror” icon and fong press the midde button [MENUJOK) o enter the mirror setting interface, short press [+ADD) or [- DEC] button, to set rightwards or leftwards image. After setting, short press [MENU/OK] twice continuously to exit the setting, the image setting will be saved for future use.

7. Parking Guideline Position Adjustment
   Select the *Parking Guide Position Adjustment” icon, then long press the middle bution [MENU / OK] to enter the setting interface, short press the [+ADD] or [- DEC] button to choose the most suitable one from 5 levels, then short press [MENU / OK] twice continuously to exit the seting.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>