EuControls S830-PL-DBT Bluetooth Mesh PIR Photo and Lighting Control Instruction Manual

EuControls S830-PL-DBT Bluetooth Mesh PIR Photo and Lighting Control

Instruction Manual

Bluetooth Wireless
S830‐PL‐DBT
PIR + Light + Photo + Temp

Product Features

• Bluetooth mesh Wireless Control of Luminaries
• Bluetooth mesh Occupancy Sensor, & Photo Sensor
• 2.4GHz, +10dBm Bluetooth transmit power
• 0-10V Analog Dimming Control, 50mA Sink
• Compatible with Electronic Ballasts & LED Drivers that comply with IEC60929 Annex E2, 0-10V Dimming.
• Best when used with Dim to Zero (Dim to OFF) Ballasts & LED Drivers

Safety and Compliance

1. UL 916 Listed
2. FCC ID: 2AJ2N-S830-PL-DZB, FCC Class B.
3. Bluetooth mesh compatible
4. Mount 1/2 Inch Trade Size Knockout, Dust Proof Design IP50

Environmental

1. Operating temperature: 0 to +60°C
2. Storage temperature range: -10C to +70°C
3. Humidity (non-condensing): 5% – 95%RH
4. Cooling: Convection
5. Vibration Frequency: 5-55Hz/2g, 30 minutes
6. Impact resistance: 1g/s

Electrical Specifications at 25OC

• Input: UL Class 2 DC voltage 12VDC (10 to 14VDC)
• Input Current Draw: 60mA, 200mA Peak during transmit.
• 0-10V Dimming intended for use with Dim to Zero/Dim to OFF Ballasts and LED Drivers.

Labeling Example

Mechanical Dimensions: Inches [mm]

Material: 5VA PC Plastic Case
Weight: TBD Grams (TBD oz.) Typical

Notes:
RED Occupancy LED Visible through PIR Lens.
BLUE Bluetooth LED Visible through PIR Lens.
S830-DBT BLUE Bluetooth LED Visible through Flat Cover
Reset switch is located on flat side of case near connector.

S830-ACC-CNR1M, 1 Meter Cable, mm (Scale ~5:1)

S830-DBT

Input Specifications

Output Specifications

Environmental Specifications

Safety & EMC Compliance

Standard Lens Coverage

FCC ID 2AJ2N-S830-PL-DBT:

Channel 0 to 39

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

To maintain compliance with FCC’s RF exposure guidelines, the distance must be at least 20cm between the radiator and your body, and fully supported by the operating and installation configurations of the transmitter and its antenna(s).

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Read More About This Manual & Download PDF:

References

• EuControls - Intelligent and Wireless Lighting Controllers

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>