MARMITEK WA300 Wireless Audio Transmission Instruction Manual
- June 13, 2024
- MARMITEK
Table of Contents
MARMITEK WA300 Wireless Audio Transmission Instruction Manual
Safety instructions
Please read these instructions thoroughly before you use the device and keep them for future reference.
- Only for indoor use.
- Do not expose the product to extremely high or lowtemperatures, strong light sources or direct sunlight.
- This product is not a toy. Keep out of reach of children.
- Connect the adapter to the mains only after you have verified that the line voltage corresponds to the value specified on the type plates.
- Never connect a power adapter if it’s damaged. In such cases, please contact your supplier.
- Disconnect the AC/DC power adapter from the mains when this device is not in use for prolonged time.
- Never open the product: the device may contain parts with deadly voltage.
- Repairs or service should only be performed by qualified personnel.
Installation
- We recommend that you switch off your equipment before connecting cables in order to prevent any of the devices being damaged.
- Record players need special phono pre-amplification to make vinyl records sound right. Many turntables have this built in, some do not. This product does not have a built-in phono preamp.
- Connect the Audio Source to the input[1] on the Marmitek WA300 transmitter using the RCA audio cable.
- Connect the Audio Destination* to the audio output [2] on the Marmitek WA300 Receiver using the RCA audio cable.
- Connect the power adapters [3] with the USB C cable to the Transmitter and Receiver and plug the power adapters into the electrical socket.
- The Transmitter and Receiver will automatically turn on and the white LED will flash slowly. On connection the LED light will be steady.
- The audio connection is ready to use
Pairing
When you want to pair an extra receiver, push the power button 2 times quickly
on the transmitter. The LED light will flash quickly. Do the same on the new
receiver. After a few seconds the LED light will light up steady and the new
receiver is operational.
Standby
When there is no audio input for more than 30 minutes, the Marmitek WA300 set
will go in standby and the LED light will turn off. When audio input is
detected again, the set will wake up in a few seconds and the wireless audio
connection will work again.
Power off
Long press the power button to turn off the transmitter and or receiver.
Frequently asked questions (FAQs)
Please go to www.marmitek.com if you have any
questions.
Technical specifications
- Audio transfer method Digital
- Transmitter frequency 2.4 GHz
- Frequency channels 26 channels
- RF connection Paired connection (TX and RX)
- Extra receivers up to 10 extra RX
- Supported audio freq. 20 Hz ~ 20 kHz
- Audio delay 12.5 ms (between TX and RX)
- Audio input/output 2x RCA (Stereo L/R)
- Operating range Up to 100 meters clear field, up to 20 meters through walls and ceilings.
- Data transfer speed Up to 2 Mbps, GFSK modulation
- Standby After 30 minutes no audio
- Power 5 VDC USB adapter with USB Type C cable
- Power consumption 0.9 W (transmitter) and 0.3 W (receiver)
- Standby (auto) <0.25 W (TX/RX)
- Standby (power button) < 0.15W (TX) and < 0.1W (RX)
- Dimensions (h x w x d) 907522mm (TX/RX)
- Weight 160 grams *e.g. hi-fi System, home cineama set, powered speakers
Declaration of Conformity
Hereby, Marmitek BV, declares that this Marmitek
WA300 set is in compliance with the essential requirements of the 2014/53/EU, 2011/65/EU and 2009/125/EC: 2019/1782 Directives. Full Declaration of Conformity is available at www.marmitek.com/en/declarations-of- conformity/ More detailed user guide and instructions are available on our website at www.marmitek.com
References
- Marmitek | Al 25 jaar specialist in slimme oplossingen
- Marmitek | al 25 jaar specialist | Smart home & wireless HDMI & audio
- Declarations of Conformity | Marmitek
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>