EVA LOGIK ZW924 S2 Remote Control Switch User Guide
- June 13, 2024
- EVA LOGIK
Table of Contents
EVA LOGIK ZW924 S2 Remote Control Switch
Product Information
The product is a Z-wave remote control switch designed for home automation.
It allows users to control various devices and appliances remotely.
- Battery Position: The battery is located inside the remote control. To access it, open the remote cap and separate the two halves of the device.
- RGB LED Indicator: The LED indicator on the remote control has different colors and flashing patterns to indicate different functions.
- Program Button: The program button on the remote control is used for adding or removing devices from the Z-Wave network.
- FCC Warning: The device complies with Part 15 of the FCC Rules and must not cause harmful interference.
- Important Safety Instructions: The device should be installed in accordance with local regulations and should not be used to control medical or life support equipment.
Product Usage Instructions
-
Powering the Device: Open the remote cap by hand and separate the two halves of the device. Remove the battery tabs. The Z-wave remote control should immediately flash its LED to indicate that it is powered.
-
Z-Wave Control: To add the device to your Z-Wave network, follow the instructions provided by your Z-Wave-certified controller. When the controller is ready to add your device, press the first button on the remote control five times.
-
LED Indicator Functions: The RGB LED indicator
The remote control has different functions and colors:- Inclusion: The LED flashes blue
- Exclusion: The LED flashes purple
- Wake up: The LED stays solid blue
- Reset: The LED flashes red
-
Additional Information:
- Read the online guidelines at support.minosto.com/Z-wave remote carefully.
- Avoid using the device in locations with direct water contact.
- Keep the device away from children as it contains small parts.
If you have any questions or need further assistance, please contact us at ask@nie-tech.com or visit our website at www.nie- tech.com.
Specifications
- Battery: CR2032*2
- Frequency: 908.42MHz
- Temperature Range: 32°F-104°F
- Indoor use in a dry location
Please read the online guides at support remote carefully
Do not use it in locations with direct water contact.
Contains small parts kept away from children.
Power the device
- Use by hand open the remote cap, and push it to separate the 2 halves
- Remove battery tabs
- Your Zwave removed Immediately should flash an LED to indicate it is powered.
S2 Remote Control Switch features
-
Power by battery need wires are needed.
Note the + direction of the battery -
Control other Z wave devices and enable scenes with a click of a button.
To add the device
- Follow the instructions for your Z-Wave certified controller to add a device from the Z-Wave network.
- Once the controller is preparing to add your device, press the FIRST BUTTON(ONLY) 5 times, The LED flashes in blue during inclusion and the LED stays on green for 2 seconds after inclusion successfully.
- If the LED flashes purple for 3 seconds, please reset the device. LED will stay on red for 2 seconds ds after inclusion fails.
To remove the device
- Follow the instructions for your Z-Wave-certified controller to remove a device from the Z-Wave network.
- Once the controller is preparing to remove your device, press the SECOND BUTTON (ONLY)5 times, The LED will flash in purple during the exclusion and the LED stays on green for 2 seconds after
the exclusion successfully. LED will stay red for 2 seconds after exclusion fails.
Wake up the Device
Press the THIRD BUTTON 5 times quickly, LED will stay solid on blue when awake
and will turn off w
hen device goes back to sleep mode.
Factory reset
Manual: Reset: Press the FOUR BUTTON 5x, then press it 5x again when the red
light is flashing.
FCC Warning
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference. (2) This device must accept any interference received, including
interference that may cause undesired operation. changes or modifications not
expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
NOTE: into an outlet on a circuit different from that to which the
receiver is the receiver is connected Consult the dealer or an experienced
radio/TV technician for help.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This transmitter must not be co-located or operating
in conjunction with any other antenna or transmitter. This equipment should be
installed and operated with a minimum distance of 20cm between the radiator&
your body.
CAUTION – PLEASE READ!
This device is intended for installation in accordance with the National
Electric Code and local regulations in the United States, or the Canadian
Electrical Code and local regulations in Canada. If you are unsure or
uncomfortable about performing this installation consult a qualified
electrician
MEDICAL EQUIPMENT
Please DO NOT use this plug to control Medical or Life Support equipment. This
device should never be used to control the On/Off status of Medical and/or
Life Support equipment.
OTHER WARNINGS
Risk of Fire / Risk of Electrical Shock / Risk of Burns
IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
- Read and follow all instructions that are on the product or provided with the product.
- do not use an extension cord.
- Reference the National Electrical Code, NFPA 70, specifically for the installation of wiring and clearances from power and lighting conductors.
- Installation work and electrical wiring must be done by a qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction.
- Do not install or use it within 10 feet of a pool
- Do not use it in a bathroom
WARNING: Risk of Electric Shock.
When used outdoors, install only a covered Class A GFCI-protected receptacle
that is weatherproof with the power unit connected to the receptacle. If one
is not provided, contact a qualified electrician for proper installation.
Ensure that the power unit and cord do not interfere with completely closing
the receptacle cover
WARNING
Risk of Electric Shock. Mount the unit at a height greater than 1 foot from
the ground surface
WARNING
Risk of Electric fire. install only to a receptacle protected by 204 branch
circuit over current protection.
SAVE THESE INSTRUCTIONS – This manual contains important safety and
operating instructions.
MEDICAL EQUIPMENT
Please DO NOT use this plug to control Medical or Life Support equipment. This
device should
never be used to control the On/Off status of Medical and/or Life Support
equipment.
OTHER WARNINGS
Risk of Fire / Risk of Electrical Shock / Risk of Burns
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>