Pro Dunk Wall King Owner’s Manual
- June 12, 2024
- PRO DUNK
Table of Contents
- WELCOME TO THE FAMILY OF PRO DUNK® OWNERS
- Bill Of Materials
- Safety Instructions
- Installation Overview
- Required Tools
- Installation
- Routine System Inspection and Safety Before Play
- Maintenance
- Hoops Inc. Pro Dunk® WALL KING Limited 5 Year Warranty
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
- 2 Phillips Screw Driver
OWNER’S MANUAL Pro Dunk® WALL KING
Basketball System
WELCOME TO THE FAMILY OF PRO DUNK® OWNERS
Thank you for purchasing our basketball system. We try hard to ensure that our products are of high quality and free of manufacturing defects and of missing parts. However, if you have any problems with your basketball pole, such as a manufacturing defect or a missing part please contact us at the following:
Toll Free: 1.888.600.8545
Pro Dunk®
Web: www.produnk.com
22047 Lutheran Church Rd.
Tomball, TX 77377
Warning
- Do not slide, climb, or play on system.
- Keep organic material away from system. Grass, litter, etc. could cause corrosion and /or deterioration.
- Check system twice a year for signs of corrosion (rust, pitting, and chipping). Remove rust and/or loose paint completely and repaint with exterior enamel paint. If rust has penetrated through the steel anywhere, replace parts immediately.
- Check unit before each use for loose hardware, excessive wear, and signs of corrosion and repair before using.
- During play, use extreme caution to keep players face away from the backboard, rim, and net.
- Wear a mouth guard when playing to avoid dental injuries.
- When adjusting height, keep hands and fingers away from moving parts.
- During play, do not wear jewelry (rings, watches, necklaces, etc.). Objects may entangle in net.
Please provide model number, serial number, and/or part number of the product
and/or part when you call, write or email. These numbers can be found on the
product, packaging, or on the back of the main pole.
Purchase Parts: www.produnk.com/parts
Support: www.produnk.com/support
Installation Video: https://www.produnk.com/support/videos.php?
id=diQJ0XzHTv0
Read this manual all the way through before starting to install your system.
Then read each step completely before beginning installation. Ensure you
understand each step fully and comply with all steps for a safe installation.
Bill Of Materials
No. | Description | Qty. |
---|---|---|
1 | Wall Bracket | 1 |
2 | Upper Extension Arm | 1 |
3 | Lower Extension Arm | 1 |
4 | Backboard | 1 |
5 | Rim | 1 |
6 | Rim Cover Plate (Packaged With Rim) | 1 |
7 | Actuator | 1 |
8 | Upper Actuator Arm | 2 |
9 | Lower Actuator Arm | 2 |
10 | Steel Height Meter | 1 |
11 | Actuator Handle | 1 |
12 | Backboard Connection Bracket | 2 |
13 | Rear Wall Support Bracket | 4 |
14 | Actuator Steel Sleeve | 1 |
15 | Plastic and Steel Rim Spacer | 4 |
16 | 16mm x 58cm Hex Bolt | 1 |
17 | 16mm x 52cm Hex Bolt | 1 |
18 | 16mm x 13cm Hex Bolt | 2 |
19 | 12mm x 8mm Hex Bolt | 2 |
20 | 12mm x 7mm Hex Bolt | 4 |
21 | 12mm x 3.5cm Hex Bolt | 2 |
22 | 10mm x 35cm Hex Bolt | 6 |
23 | 10mm x 35cm Eye Bolt | 1 |
24 | 10mm x 7cm Hex Bolt (Packaged With Rim) | 4 |
25 | 6mm x Phillips Bolt (Packaged With Rim) | 2 |
26 | 16mm Nylon Hex Locknut | 4 |
27 | 12mm Nylon Hex Locknut | 8 |
28 | 10mm Hex Nut | 4 |
29 | 16mm Flat Washer | 8 |
30 | 12mm Flat Washer | 16 |
31 | 10mm Flat Washer | 14 |
32 | 10mm Flat Washer | 12 |
33 | 10mm Lock Washer | 4 |
34 | Safety Cable Clip | 1 |
35 | Safety Cable Mounting Bracket | 1 |
36 | Steel Safety Cable | 2 |
37 | 10mm Nylon Hex Locknut | 7 |
38 | Masonry Drill Bit | 1 |
39 | Wood Drill Bit | 1 |
40 | Height Sticker | 1 |
Safety Instructions
IMPORTANT
It is the responsibility of purchaser to ensure that all installers and
players fully comply with the detailed instructions set forth in this product
installation manual.
Product assembly should be carried out exactly as instructed and owner
supervision of use and installation is required to prevent risk of product
malfunction or risk injury.
- All tools used to assemble this product should be used in compliance with manufacturer’s guidelines.
- Installation of this product will require heavy lifting and bending. Any person that is not capable of such activity should not participate in the installation of this product.
- If using a ladder during assemble, use extreme caution and refer to the warnings and cautions on the ladder.
- Due to the size and weight of this product, we recommend at least (4) competent adults are present.
- Make sure there are no overhead power lines within a 25 foot radius of the basketball system.
- All parts and components necessary to complete proper installation are included within this product. Do not use parts not included with our system. Failure to follow this requirement could cause product malfunction and will void warranty of this product.
- Keep all organic materials away from parts and components to avoid corrosion.
- Do not Dunk or Hang on your system.
- Do not climb on any part of the basketball system as it was not intended for this activity.
- The owner is responsible for ensuring the wall or structure the system is mounted to is structurally sound and capable of supporting the stress of the system. Contact a professional engineer evaluate your structure beforehand.
- Do not use the basketball system as a lift or to hoist anything.
- Players should wear protective mouth guard during play to avoid any time of dental injury.
- Players should refrain from wearing any jewelry that could potentially get caught in the rim or net.
- Do not allow children to adjust basketball system.
- Check the basketball system on a regular basis to ensure that there are no signs of deterioration or corrosion, loose hardware, or damaged parts. If you see any signs of damage perform maintenance or contact Prounk® for replacement.
- For maintenance repairs please contact a professional.
- During installation be sure the wall is clear of any type of utilities (wires, gas lines, water lines, etc..)
- Be sure you have safe access to the rear side of the wall to complete the installation.
- Failure to follow these safety instructions could result in product malfunction, serious injury, or even death.
Pro Dunk® retains the right to modify this document at any time without notice
or obligation.
Keep this installation manual as a reference for your safety and the safety of
those playing on the basketball system.
Additional copies of these safety instructions are available by calling
customer service at 1.888.600.8545 or at www.produnk.com/support
Installation Overview
In order to have the safest, fun and longest use of your Pro Dunk® system, please note and heed the following:
- Prior to goal assembly, ensure the structure the system is being mounted to is structurally sound and capable of supporting the system. We recommend contacting an engineer to evaluate to structure as well.
- Installation requires full access to the rear side of the structure.
- Immediately unpack all components and cross check against bill of materials. Report any shortages to Hoops Inc. customer service at 1.888.600.8545.
- Parts can be ordered at www.produnk.com/parts
- For safety measures, have at least 4 capable persons to assist you in assembly of your system.
Wall King Installation Video
https://www.produnk.com/support/videos.php?id=diQJ0XzHTv0
Required Tools
- Power Drill (Hammer drill for brick and stone)
- 2 Adjustable Wenches
-
2 Phillips Screw Driver
- 2 8ft Ladders
- Level
- Pencil
- Tape Measure
Socket/Wrench Sizes Recommended
- 24mm
- 22mm
- 17mm
Why stop playing in the evening. You don’t have to! Order the Pro Dunk Goal
Light LED. It easily lights up the entire 3-point line with 2 powerful LED
lamps extending play into the night.
There’s always time for one more game! [patent pending 62458721] Comes with
Free Shipping!
Goal Light LED!
produnk.com/video/goal_light_led.html
Need a dedicated net or lighting for your court. Our Boundary Netting has got
your covered. This accessory isfully customizable and is a standalone net,
light, and/or flag. Below is a link to our builder. Customize your court!
Comes with Free Shipping!
Dedicated Net
produnk.com/video/boundary_netting.html
Haven’t you always wanted your playing area to have regulation striping like a
real basketball court. Well now you can with the Court Marking Stencil Kit.
Just lay it out on your court and applied the included white paint. Includes
the key with side markings, freethow, and the entire 3-point line. Fully
reusable and a great family DIY project. Comes with Free Shipping!
Court Marking Stencil
produnk.com/video/court_marking_stencil_kit.html
Looking to light up your court from multiple locations? The Pole Light LED can
be mounted anywhere and will light up your entire court. You can have multiple
sources of light to cancel out any shadows during place and truly bring the
gym experience home! This even has a flag option to put up your favorite flag
and fly it proud! Comes with Free Shipping!
Pole Light LED
produnk.com/video/pole_light_led.html
Installation
1) Installation Location
Choose the proper location to mount your Wall King system. Use the diagram to
the left to make sure your bracket is high enough to be adjusted up to 10ft.
If you install your bracket higher than 86 inches your system will still
adjust to 10ft but will not adjust down as far. If you install your bracket
below 86 inches your system will not adjust up to 10ft.
The wall surface needs to be level and flat so that your bracket will be
level. The wall must either be wood siding, brick, or stone and be
structurally sound.
Ensure that the structure you are mounting to is structurally sound and
sufficient to handle the stresses of the Wall King.
Contact a professional engineer regarding this.
Above your bracket you need an additional 6 – 16 inches for the safety cable
to attach to the wall (16 inches being optimal).
You must have full access to the rear side of the wall to complete the
installation.
Before moving on confirm you have read and understand all safety instructions
on page 3.
The overhang is 3ft from the wall to the front of the backboard.
2) Marking and Drilling Bracket Mounting Holes
Using a pencil, mark the 2 top mounting holes, 2 bottom holes, 2 of the 6
center holes (1 on the left and 1 on the right), and the safety cable eye
bolt hole while ensuring the bracketis level. (Total of 7 holes to be drilled)
Once marked check the wall to make sure there is nothing in the way of
drilling through the wall. Example: electric wiring, steel braces/studs,
water lines, gas lines, or anything else.
Brick/Stone Wall:
Next using the provided drill bit(s), drill each hole. Use the #38 masonry
drill bit and a hammer drill to go through the brick or stone. Once through
the brick or stone switch to the #39 wood drill bit to go through the rest of
the wall.
Wood/Siding Wall:
Using the #39 wood drill bit, drill each hole.
3) Bracket Installation
Rear access to the wall is required to mount the wall bracket.
Next install your #1 wall bracket to the wall using the 6 #22 bolts, 12 #31
flat washers, 6 #37 hex nuts, and 3 #13 rear wall support brackets.
Before tightening make sure bracket is level.
Parts:
[1] #1 Wall Bracket
[3] #13 Rear Wall Support Brackets
Hardware:
[6] #22 10mm x 35cm Hex Bolts
[12] #31 10mm Flat Washers
[6] #37 10mm Nylon Hex Locknut
4) Safety Eye Bolt
Install your safety eye bolt through your wall.
Parts:
[1] #13 Rear Wall Support Bracket
Hardware:
[1] #20 12mm x 7cm Eye Bolt
[2] #31 Flat Washers
[1] #37 10mm Nylon Hex Locknut
5) Extension Arm Assembly
Once your bracket is secured to the wall it is now time to assemble the upper
and lower extension arms.
Parts:
[1] #2 Upper Extension Arm
[1] #3 Lower Extension Arm
[2] #8 Upper Actuator Arms
Hardware:
[4] #20 12mm x 7cm Hex Bolts
[8] #30 Flat Washers
[4] #27 12mm Nylon Hex Locknuts
6) Actuator Assembly
Next assemble your actuator as shown to the right.
Parts:
[1] #7 Actuator
[2] #9 Lower Actuator Arms
[1] #14 Actuator Steel Sleeve
[1] #10 Steel Height Meter
[1] #11 Actuator Handle
Hardware:
[2] #18 16mm x 13cm Hex Bolts
[4] #29 16mm Flat Washers
[2] #26 16mm Nylon Hex Locknut
[2] #21 12mm x 3.5cm Hex Bolts
[4] #30 12mm Flat Washers
[2] #27 12mm Nylon Hex Locknut
7) Backboard Assembly
Next assemble your Backboard Connection Brackets and backboard as shown
above. Parts:
[1] #4 Backboard
[2] #12 Backboard Connection Brackets
Hardware:
[1] #17 16mm x 52cm Hex Bolt
[1] #16 16mm x 58cm Hex Bolt
[4] #29 16mm Flat Washers
[2] #26 16mm Nylon Hex Lock-
[2] #19 12mm x 8cm Hex Bolts
[4] #30 12mm Flat Washers
[2] #27 12mm Nylon Hex Locknut
CAUTION: Do not proceed with rim assembly without these spacers!
Install Rim Spacers
https://www.produnk.com/support/videos.php?
8) Rim Assembly
Next assemble your rim as shown to the rightand level rim left to right.
Parts:
[1] #5 Rim
[1] #6 Rim Cover Plate (Packaged With Rim)
[4] #15 Plastic and Steel Rim Spacer
Hardware (Packaged With Rim):
[4] #24 10mm x 7cm Hex Bolts
[8] #32 10mm Flat Washers
[4] #33 10mm Lock Washer
[4] #28 10mm Hex Nut
[2] #25 6mm Phillips Bolt
Make sure all hardware on the system is tightened at this point.
9) Safety Cable Assembly
Next assemble the #34 Safety Cable Mounting Bracket to your Backboard.
Loosen the 2 H-Bracket bolts and install the #34 Safety Cable Mounting Bracket
to the top of the backboard as shown.
Once secured connect the #35 Steel Safety Cable using the 2 #36 Safety Cable
Clips as shown.
Parts:
[1] #34 Safety Cable Mounting Bracket
[2] #36 Safety Cable Clips
[1] #35 Steel Safety Cable
10) Height Sticker Assembly
To apply the #40 Height Sticker, first use a tape measure to crank rim up to
exactly 10′ from the playing surface. This is measured from the top of the rim
to the playing area. Then apply your #40 Height Sticker to the actuator where
the #10 Height Meter is pointing at 10ft exactly. Your system is now
calibrated and you will have a general idea of what height the system is at
while adjusting it up and down.
Please remember if you did not mount your bracket at exactly 86” you will not
have the full range of adjustment and will need to understand the limitations.
You can reference Step 1 or give our support staff a call if you have any
questions.
Routine System Inspection and Safety Before Play
Before each use inspect the entire system for any signs of loose nuts and
bolts, any excessive wear and tear, any signs of rust or corrosion.
If replacement parts are needed you can contact Pro Dunk® directly or navigate
to www.produnk.com/parts to purchase parts for your system. Only parts
provided by Pro Dunk® should be used for repair. Not doing so could cause the
system to fail resulting in
injury or death and voids the limited lifetime warranty.
Be sure you and all players have read and fully understand all safety warnings
on page 3.
DO NOT DUNK OR HANG ON THIS BASKETBALL SYSTEM.
Maintenance
Like any piece of hardware proper maintenance is required. Several factors such as the environment, organic materials, herbicides, pesticides, excessive use or misuse can eventually cause the basketball system to require maintenance. Failure to do so could result in system failure, property damage, or even personal injury.
-
All organic materials should be kept away from the system at all times. This will alleviate any chance of rust penetrating the powder coated finish and causing structural damage.
Examples: grass clippings, moisture, garbage, dirt, etc. -
If you see any signs of rust on the system remove the loose paint, sand the area with a media grit sandpaper and apply outdoor enamel to the affected area. Suggested Touchup Paint: Rustoleum Semi-Gloss Black Enamel
-
To clean the backboard use a 100% cotton soft cloth with mild dishwashing liquid for soap and luke warm water. Rinse backboard with lukewarm water. Wash gently with a 100% Cotton soft cloth, lukewarm water and mild soap. Do not scrub. Rinse backboard with lukewarm water again. Dry with 100% cotton soft cloth. To minimize scratches and minor abrasions to your backboard
-
Never adjust the rim outside the adjustment range based on your installation. Adjustments of thegoal should be done under adult supervision.
-
If installed in a public area it is suggested to remove the adjustment handle.
-
Replace Net Video—
Replace Net
https://www.produnk.com/support/videos.php?id=-Llue54A4cs
Hoops Inc. Pro Dunk® WALL KING Limited 5 Year Warranty
Hoops Pro Dunk® WALL KING basketball structural components are warranted to
the original purchaser to be free from defects in material or workmanship for
the duration of ownership by the original retail purchaser. The word “defects”
is defined as imperfections that impair the use of the product.
Warranty Fulfillment
Merchandise must be shipped prepaid with a copy of proof of purchase to Hoops
Inc. for examination to see whether it needs to be repaired or replaced. Any
labor costs, travel expenses and any other changes involved in the removal,
installation or replacement of the defective/repaired parts from/to your Hoops
Pro Dunk® WALL KING system will be your (the purchaser’s) responsibility.
Shipping charges for replaced or warranted merchandise being sent back to the
customer must be prepaid by the customer in advance. If not, the replacement
shipment will be sent out collect. Hoops Inc. reserves the right to examine
photographs or physical evidence of merchandise claimed to be defective, and
to recover said merchandise, prior to authorization of warranty claims.
What is not covered by this warranty
This warranty does not cover defects or damage due to improper installation,
shipping, handling, alteration, accidents, vandalism, weather conditions
(rusting), exposure to corrosives, negligence, misuse (anything other than a
type of basketball activity or related contact with the unit), scratching,
scuffing or any event beyond the control of the Hoops Inc.. If unit is not
maintained as stated in the user manual the warranty will be void.
Liability
Hoops Inc. shall not be liable for indirect, special, or consequential damages
arising out of or in connection with the use or performance of the products or
other damages with respect to any economical loss, loss of property, loss of
enjoyment of use, costs of removal, installation or other consequential
damages for breach of any expressed or implied warranty on these products. All
installations must have a final engineering sign off before use and yearly
inspections by a professional certified to do so or specified by the engineer.
Guidelines
Keep your proof of purchase (original retail purchaser). Without it, we will
not be able to proceed with any warranty service.
Call
1-888-600-8545 / Warranty Dept.
Write
Hoops Inc.
Attn: Warranty Dept
22047 Lutheran Church Rd.
Tomball TX 77377
Email: support@hoopsincorporated.com
For the most up to date warranty information please navigate to
www.produnk.com.
References
- Official Pro Dunk® Basketball Hoops
- Accessories
- Order Parts
- Customer Support
- All Videos
- All Videos
- All Videos
- All Videos
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>