Kingnode E-304 Electronic Series Gummed Tape Dispenser Instruction Manual

E-304 Electronic Series Gummed Tape Dispenser
Instruction Manual Original Instruction Manual
E-304 Electronic Series
Gummed Tape Dispenser
Manufacturer: Kingnode (Fujian) Technology Co., Ltd.
Address: No.11 Xiazhai Road, Hua An Economic Development Zone,
Zhangzhou, Fujian, 363000, China.
Email: info@kingnodetech.com
Website: www.kingnodetech.com

Part I Preface

Welcome to buy and use the E-304 series wet water kraft tape cutting machine designed and produced by our company.
This series of equipment is mainly used as a special power tool for wet water kraft sealing tape, it can quickly complete the wet water and fixed length cutting one time, greatly improving the efficiency of sealing work, meanwhile it will be conducive to wet water kraft tape as an environmentally friendly tape widely used in the field of sealing packaging. Compared with other similar equipment, this series of equipment mainly has the following advantages.

• The world’s first IntelliSense dispenser, equipped with intelligent computer numerical control interface and infrared sensor. It has the Manual Cutting Mode, and the IntelliSense & Auto Cutting Mode. Under the IntelliSense & Auto Cutting Mode, you can flexibly choose either Infrared Sensing Cutting or Automatic Cutting Mode.
• It is applicable to 100V~240V, not subject to international regional voltage restrictions.
• We can select 12 different lengths under Manual Cutting Mode, which can meet different sealing requirements and reduce the machine downtime.
• Model E-304BHP with built-in large-capacity lithium battery, to ensure the smooth operation in case there is no power access or temporary power outage in the workplace. And the maximum working time can reach 8 hours.
• E-304HL is equipped with enlarged tape loading structure, the maximum loaded diameter size can reach 300 mm. And we can load the tape with 3 different sizes of paper cores, 38mm, 48mm and 76mm.
• Equipped with movable pressure plate weight (fixed on the bottom of the equipment tape outlet side). According to the different thickness of the paper tape, the user can adjust the wet water uniformity by adding or reducing the weight. Both reinforced or non-reinforced kraft paper tape can be used.

In general, this cutting machine has the advantages of safety, efficiency, convenience and environmental protection. The design concept is leading and humanized. It is currently the world’s leading WAT dispenser. We hope it can bring you a different sealing experience.
This operating manual solely provides necessary information about the machine operation, maintenance and repair of the E-304 WAT Dispenser, does not serve as a warranty of the product.
Disclaimer: in order to provide better assistance and guidance to our users, we reserve the rights to make necessary revisions and improvements to this operating manual without notifying users in advance.
Please read this Operating Manual carefully before using the equipment to ensure that the operator fully understands the function and the performance of the machine, and make sure to handle this dispenser correctly and safely.
If you want to know more about this product or need help, please contact our company directly, our contact information is as follows: Manufacturer: Kingnode (Fujian) Technology Co., Ltd.
Telephone: +86-400-6169-833
Website: www.kingnodetech.com

Part II Unpacking and Inspecting

When you receive the equipment and open the package, please check the equipment model according to the following Packing List and take a video of the whole process, in case there’s a complaint to our after-sales staff when the parts are missing. Kindly to keep the package properly for subsequent moving or transportation.
Attachment： Packing List

Model Number| Host| Power Cords| Power
Adapter| Water
Tank| Water
Box| Brush| weights| Tool Kit
---|---|---|---|---|---|---|---|---
E-304H/304HP| 1| 1| | 1| 1| 2| 3| 1
E-304BHP| 1| | 1| 1| 1| 2| 3| 1
E-304HL| 1| 1| | 1| 1| 2| 3| 1

Note: The water tank, water box, brush and weights have been installed on the equipment host before delivery

Part III Safety Precautions

In order to avoid personal injury caused by improper use of the equipment, please read and follow the safety instructions accordingly:

1. Please read this operation manual carefully before using the equipment to ensure that you have fully understood the performance of the equipment and mastered the correct operation and maintenance methods.
2. If the machine is not installed and used properly, it may cause interference to radio communications (but fully complies with the relevant provisions of the FCC). If the device is used in a residential area, necessary measures need to be taken to eliminate the interference of the device with radio communications.
3. Prior to cleaning of the tape jam, make sure the power is turned off. When there is a need of professional cleaning for the equipment which might lead a breakdown or damage of the machine, please turn to a technician specifically.
4. When the equipment is necessary to be moved to the next workplace, please ensure that the power is off, then remove the Water Bottle, Reservoir and the Moistening Brushes to prevent electric shock hazard due to the spill of water.
5. The remaining heat exists on the surface of the metal parts attached to the heater may cause severe skin burn. Please do not touch it without taking any protective measures.
6. Use of tape products or machine parts not recommended by the equipment manufacturer may increase unsafe factors.
7. During the storage, transportation and handling of this product, please guard against squeezing, falling and impacting, so as to avoid deformation and damage of equipment parts, which will affect the performance of the product.
8. Since the product contains sharp parts such as cutting knife, the product should be placed and used away from children’s reach to avoid personal injury.

Part IV Technical Data and Illustration

Technical Parameter Data
Technical Data of E-304 Series WAT Dispenser:

Illustration of the Machine

Equipment Electrical Schematic Diagram

Part V CNC Operation Interface Directions

Interface 1: Startup Screen
When you turn on the power switch of the device, the CNC display screen will automatically enter the startup interface as shown in Figure 3. After the interface flashes for about 3 seconds, the device will automatically enter the “IntelliSense & Auto Cutting Mode” interface as shown in Figure 4. info@kingnodetech.com
www.kingnodetech.com

Interface 2: IntelliSense & Auto Cutting Mode This interface is composed of a combined cutting task editing area and main function keys. The specific functions are introduced as follows:
Introduction of function keys

1. Reset: Initial cutting length calibration, reset button. Cutting precision can be controlled within ±3mm, which can effectively reduce the wastage of tape.
2. Heating: Start the heating function of the Reservoir. In low temperature . working environment can effectively ensure the tape wet water uniformity and good sealing effect.
3. Parameter: Press this function key to pop up the password input interface and enter the password (8888) to enter the “Parameter Setting” interface as shown in Figure 6.
4. Manu/Auto: Used for autonomous switching between automatic mode and anual mode.
5. Length: Set the cut length, the default unit is feet, which can be switched to centimeters by clicking “Length”.

Combined Cutting Task Editing Area

1. S/N: The serial number of the work task instruction;
2. Length: Used to set the cutting length (unit: cm);
3. 1/2: Used to set the number of cut sheets corresponding to the specifications of each sealing cycle (1 or 2 pieces), which is mainly used in the “H” type box  sealing scenarios.
4. Setting (pcs): Used to set the cutting quantity for the corresponding specification, the system default value is 9999. User can click the “Setting Pcs” value corresponding to the cutting task to modify the cutting quantity according to their needs.
5. Completed (pcs): Used to realize the number of stripes that have been cut. When the value of “Completed pcs” is equal to the value of “Set Pcs”, the corresponding cutting task is completed and the device stops performing the task.
6. ON/OFF: It is used to set the “ON” or “OFF” status of the work task in the corresponding work task line.
7. Total Length(m): Display the cumulative length of cutting tape (unit: m). Long press the display area for 3 seconds to clear the data.
8. Induction cutting/ Auto cutting: Used to switch between “Induction cutting” and ” Auto cutting” modes.

Interface 3: Manual Cutting Mode

This interface is the main interface for manual cutting mode setting. It consists of an edit area and main function keys. The button numbers 10, 20, 30, …, 120 in the interface are the factory default cutting lengths corresponding to the 12 buttons (unit: cm). User  an edit and set the cutting length corresponding to the 12 buttons according to actual needs. The description of each function key is the same as the previous introduction.
Interface 4: Parameter Setting The specific descriptions of the items displayed on this interface are as follows:

1. Pulse Frequency: the number of cycles produced across the gap in 1 second.
2. Acceleration Time: The time required for the stepping motor to reach a stable feeding speed from starting.
3. Gear Ratio: The technical ratio of gear mechanism to calibrate the cutting length error.
4. Total Cutting Operation：Display the cumulative use times of the cutter. Long press the display area for 3 seconds to clear the data.
5. Total Cutting Length：Displays the cumulative length of the tape that has been cut, in meters. Long press the display area for 3 seconds to clear the data.
6. Delay Time: A span of time during which two same actions occurred.
7. Return: Press this key to return to the previous operation interface.
8. Restore Setting: Press this key, all the device parameters will be restored to the factory preset values.

Interface 5: Time Setting
When you enter interface 2 (Figure 4), interface 3 (Figure 5) and interface 4 (Figure 6), you will find a long string of numbers “2021/00/00 00:00:00” in “Date + Time” format below the name of the interface. Long press this area for 3~5 seconds to enter the date and time setting interface (Figure 7).

Part VI Operating Instructions

The specific operation method of E-304 is as follows:
First Step: Fill Water.
Remove the water bottle from the dispenser. Fill water up to 4/5 volume of water bottle. Wait for the water filling up the reservoir to a appropriate height. Install water bottle to the original position to finish the filling process.
Second Step: Install the Tape Roll.
Open the front and rear covers, pull the spring pressure roller and remove the pressure plate. Place the water-activated tape roll (gummed side down) on the two rollers. Pull the tape (front-end) backwards through the feed roller (gummed side down) and make it under the pressure roller. Put the press plate back to its original position to complete the installation. Third Step: Increase/Decrease the Weight on Pressure Plate.
We need to make sure the two brushes totally in wet condition and the brushes at their right angle.When choose reinforced water activated paper tape, the weight (fixed on the bottom plate at the outlet side and needs to unscrew) on press plate needs to be installed into the cylinder to ensure the tape wet evenly. If use non-reinforced water-activated tape, whether to install the weight or not is subject to the actual tape thickness, to ensure the best wet water effect. Fourth Step: Operation Mode Choose and Operation Method
Plug in the electricity and turn on the power. Press the reset button, the machine will cut off the extra leading edge. In order to meet diversified sealing operation, this dispenser is designed with IntelliSense & Auto Cutting Mode and Manual Cutting Mode. Users can choose according to actual needs.
“IntelliSense & Auto Cutting Mode” is designed for “I” type dispensing, “H” type dispensing and enhanced tape dispensing. Specific operation method: Set the dispensing tape length and quantity and at S/N 1 and S/N 2 under IntelliSense & Auto Cutting Mode. Press the “ON” button. If you need enhanced type box sealing, you can set the dispensing tape length and quantity and at S/N 3. Press the “ON” button. If you need “I” type box sealing, you can set dispensing tape length and quantity and at any S/N.
In “induction cutting” mode, when you set the parameters of cutting tasks, press the “on/off” button and reach the tape outlet to get the cut tape for sealing.The “Auto Cutting” mode is a timed or delayed automatic cutting mode, users can set the interval time according to the actual sealing speed by clicking the number below the “Auto Cutting” function key (factory default setting: 3 seconds).
Manual Cutting Mode is suitable for application scenarios where multiple specifications are frequently switched. Specific operation method: Set the cutting length for the 12 buttons in the “Manual Cutting Mode” interface (factory setting value: 10, 20, 30…120) . And then press the corresponding button to conduct the tape cutting operation.

Part VII Daily Maintenance

In order to achieve the best results, in the process of using the E-304 series water activated tape dispenser, users need to perform necessary and simple maintenance. As a supplier of this equipment, we recommend the following daily maintenance work:

1. Check the water level of the water bottle frequently to avoid the poor effect of the tape moistening due to lack of water in the water bottle.
2. Regularly clean the water brush, water bottle and reservoir with soapy water to avoid the accumulation of adhesive that affect the moistening effect of the tape.
3. Regularly use lubricating oil to lubricate the rotating parts of the equipment, such as the bearings and transmission belts, to avoid any running jams or blockages.
4. When the tape is jammed, carefully check and clean the channel to avoid tape jam again.

Part VIII Common Troubleshooting

During use, some minor faults may occur due to improper installation or operation. In order not to affect your use, we recommend that you first check and resolve the faults according to the following guidance.

No.

| Failure Description| Possible Reasons|

Solution

---|---|---|---
1| External power is applied, but the device does not start normally.| (1) The device switch is not turned on.
(2) The equipment plug is not properly inserted.
(3) The electric outlets are not working.| (1) Turn on the power switch of the equipment.
(2) Make sure the equipment is plugged in.
(3) Turn on the electric outlets or insert the plug into a power socket.
2| No access to an external power source, the device can not be started properly.| (1) The device switch is not turned on
(2) The battery is low or exhausted.| (1) Turn on the power switch of the equipment.
(2) Move the device to a place with external power supply for charging.
3| The device can be turned on normally, but the device did not execute the cutting command to cut the tape when it reached out to take the tape.| (1) The work order is not opened and is in the “OFF” state.
(2) The position where the operator extends the hand is not within the sensing area of the infrared sensor of the equipment.| (1) Enter the task editing interface, click the task status button, and switch “OFF” to “ON”.
(2) Reach out your hand within the sensing area of the infrared sensor of the device.
4| The tape is not evenly wet and sealed nonstick.| (1) There is adhesive residue on the channel, water brush or outlet of the water bottle
(2) Insufficient water in the water bottle or reservoir
(3) The user has replaced the unqualified water brushes or placed the water brushes improperly;
(4) Poor quality of the adhesive tape selected by the user;
(5) Unevenly press the tape during the sealing process.| (1) Thoroughly clean the tape channel, water brushes or outlet of water bottle, and perform regular maintenance as required.
(2) Add an appropriate amount of water to water bottle and the reservoir;
(3) Purchase and use qualified water brushes, and place the brushes as required.
(4) Purchase and use qualified tape; If use reinforced water activated tape, users need to install weights on pressure plate.
(5) Press the surface of the tape evenly and make it evenly stressed during the sealing process.
5| The tape is often wrinkled, or jammed.| (1) Improper installation method of tape roll;
(2) Adhesive residues accumulate on the channel or water brushes;
(3) The tape selected by the user with poor quality;
(4) The incision of the paper is not neat.| (1) Re-install the tape roll as required, especially check whether the pressure plate is placed correctly;
(2)  Check and thoroughly clean the channel or water brushes, and perform regular maintenance as required;
(3)  Purchase and use qualified tape;
(4)  Adjust the blade to the appropriate position.
Remark: If the problem is still not resolved through the above troubleshooting, please contact our professional after-sales service personnel.

Part IX After-Sales Service

The warranty period is two year from the date of purchase of the equipment.
We provide the service of repairing and replacing defective parts of the machine free of charge during this period. The expired warranty period and the repair services outside the warranty range are not covered by the warranty. The repair cost will be charged under the following situations:

1. The damages caused by equipment handling, equipment installation and improper use;
2.  The damages caused by natural disasters or other force majeure factors if user arranges transportation individually;
3. The damages caused by individually dismantling or replacing any internal components of the equipment;
4. The equipment is damaged due to the guidance of non-our professional technicians or failure to follow this operation manual;
5. Quick-wear part such as blade, water bottle, reservoir, brush, etc. are not covered by the warranty.

Catalog of Water-Activated Tape Dispenser Series:

No.

| Item No.| Product Name|

Remark

---|---|---|---
1| P-104| Pull & Tear Gummed Tape Dispenser|
2| M-204| Manual Gummed Tape Dispenser|
3| E-304H| Electronic Gummed Tape Dispenser (with heater)|
4| E-304HP| Electronic High Speed Gummed Tape Dispenser (with heater)|
5| E-304BHP| Electronic High Speed Gummed Tape Dispenser (with lithium battery and heater)|
6| E-304HL| Electronic Gummed Tape Dispenser (larger size with heater)|
7| E-404H| Electronic Gummed Tape Dispenser (with heater)|
8| E-404HL| Electronic Gummed Tape Dispenser (larger size with heater)|

Appendix: Maintenance Service / Repair Record
Maintenance Service / Repair Record Card

User Information

Customer Name| | Purchase Date|
Model No.| | Telephone Number|
Email Address| | Postal code|
Address|
Dealer Information
Dealer Name| | Telephone Number|
Email Address| | Postal Code|
Address|
Maintenance Records
S/N| Warranty Reasons| Repair Content| Customer Acceptance| Maintenance Personnel
1| | | |
2| | | |
3| | | |
4| | | |
5| | | |
6| | | |
7| | | |
8| | | |
9| | | |
10| | | |
11| | | |
12| | | |

Fujian, China – Zhangzhou
Fujian Jialong Adhesive Tape Co.,Ltd.
Kingnode (Fujian) Technology Co., Ltd.
No.11 Xiazhai Road, Hua An Economic Development Zone,
Zhangzhou, Fujian, 363000, China.
Tel: +86-596-728-0001
Fujian, China – Xiamen
Fujian Jialong Adhesive Tape Co.,Ltd. Xiamen Branch
Room 2109, Building A, Xinjing Center, Jiahe Rd 21st,
Siming District, Xiamen, Fujian, 361007, China.
Tel: +86-592-207-5506
Email: info@kingnodetech.com
Web: www.kingnodetech.com
Guangdong, China
Fujian Jialong Adhesive Tape Co.,Ltd. Guangdong Office
Building D, Gate 1, Shalong Road, Delang Industrial Park,
Shatang Community, Houjie Town, Dongguan,Guangdong,
523955, China.
Tel: +86-769-3386-2122
Shanghai, China
Shanghai Jialong Fiber Tape Co.,Ltd.
Floor 3, Building 1,No.80 Xiangmin Road, Chedun
Town, Songjiang District, Shanghai, 201611, China.
Tel: +86-21-5108-3676
USA
Kingnode America Inc.
636 Innovation Dr,Winder, GA 30680,USA
Email: info@kingnodetech.com
Web: www.kingnodetech.com

http://www.kingnodetech.com

References

• Filament Adhesive Tape ,self adhesive kraft paper tape,tape dispenser
• Filament Adhesive Tape ,self adhesive kraft paper tape,tape dispenser

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>