Hapadif M100 pro Motorized Blinds No Drill Automatic Blinds Installation Guide

Hapadif M100 pro Motorized Blinds No Drill Automatic Blinds

Details of Parts Included in Package

Battery installation

Change The Battery

1. Remove the shade.
2. Open the battery cover.
3. Replace the battery (AA6)
4. Close the battery cover.
5. Install the shade on the bracket.

Installation Guide

Inside Mount
Inside Mount: No Tools-No Drill design allows it no need to drill any holes on your window frame, easy to install

1. Install the trim panel bracket.
2. Push the shade to the left and press against the wall.
3. Papup to the minow tenade
4. Tighten the safety lock.
5. Install the trim panel.

Outside Mount

1. Decide on and mark the positions of the two brackets with a pencil.
2. Drill holes at marked locations using pencil marks as a guide. (We suggest marking at 1/3 and 2/3 of the total length of the shade.)
3. Install the trim panel bracket. Hook the headrail of the shade into the front of the bracket, and rotate the headsail until the back of it securely snaps into place.
4. Install the trim panel.

NOTICE

• Please read the installation instructions carefully to familiarize yourself with safe and effective usage before use. In addition, keep the installation instructions handy when using the product.
• The brackets and screws apply to the wooden window frames, plasterboard walls and concrete walls, but they cannot be installed onto the window frames or ceiling which are not made up of wood, plasterboard and concrete.
• Please check the materials and hardness of the window frames or ceiling before installation.
• Make sure to comply with the number of brackets and installation location required in the installation instructions when installing the products. Improper installation could cause the shades to drop and
• bring damage to health or property.
• Please do not hang any items on the product or pull the product roughly or fiercely.
• The product is only suitable for indoor use and not for outdoor use.
• Please do not use the product in a high-heat or humid environment (such as saunas or furnaces), or near an open flame.
• Please close the window or push the shades up during high winds, otherwise, the strong winds could cause damage to the product or an accident.
• Please do not place any items that can interfere with operating the shades within a range of moving up and down.

Function Key Description

The shade has been adjusted to the best condition before delivery, so it does not need to be adjusted again. If you want to adjust, please refer to the following advanced setting functions.

Quick Matching

Please refer to the manual according to the purchased remote control model.

Step 1
Install the dry battery. Make sure the motor is energized.

Step 2
Hold the M key of the blind for two seconds, and the motor of the blind rotates forwards and backwards once to active;

Step 3
Hold the S key of the remote for two seconds and the motor of the blind rotates forwards and backwards once to indicate that the remote and the blind are linked;

Step 4
Use the up button on the front of the remote to set the highest upper position to a proper position, and then press the pause button to stop. Hold the upward arrow on the back of the remote for 2 seconds, and the motor rotates once to lock the position of the highest upper position;

Step 5
Use the down button on the front of the remote to set the lowest bottom position to a proper position, and then press the pause button to stop. Hok the down arrow on the back of the remote for 2 seconds, and the motor rotates once to lock the position of the lowest bottom position.” In admin mode, you can switch between inching operation and continuous operation, to adjust the blind more accurately.

Advanced Settings
Please refer to the manual according to the purchased remote control model. The “admin” mode Emitter channel shows a slow flash.

Motor reversing
The running direction of the blinds is opposite to what shows on the emitter button.

Delete emitter matches

1. The swich selects”admin” mode
2. Press “S” 5 times, and the motor rotates once. The match is deleted.

“user” mode
In user mode, you can operate and use this product normally without worrying about any misoperation with the motor.

Add a new emitters
A motor can match one or more emitters emitters need to be matched. See”emitter quick matching”

There’s a quick way to copy it.

1. The switch selects”user” mode.
2. Operate matched emitter. (Select the channel you want to copy.)
3. Press”S” 1 time, the motor rotates once
4. Press”S” 1 time again, the motor rotates once
5. Operate emitter to be added. (Select the channel you want to add)
6. Press”S” 1 time, the motor rotates once
7. Copy complete. Repeat 1-2, delete emitter.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>