OSMO TopDetect R7 User Manual

: June 12, 2024
: OSMO

Table of Contents

OSMO TopDetect R7
Basic Info
How To Use
Camera Detection
Technical
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

OSMO TopDetect R7

TopDetect R7
User Manual
If you want to read this user manual in a different language, visit osmousermanual.com.

Basic Info
Technical Specifications

Frequency: 1MHZ-8000MHZ
Probe dynamic range: >73dB
Detection sensitivity: Less than or equal to 0.03mv
2.4G Detection Range: 10 square meters
1.2G Detection Range: 15 square meters
Mobile frequency 2G, 3G, 4G signal Detection Range: 15 square meters
Power supply: Built-in 3.7V 1000mA battery
Charging time: 2.5 hours
Continuous working time: Up to 5 hours
Material: ABS
Size: 117x56x20mm

How To Use
RF Signal Detection

Turn on the TopDetect device.
Rotate the sensitivity adjustment knob clockwise to the maximum.
You will hear a long beeping sound which means the device has entered detection mode.
To adjust the sensitivity, turn the knob to the first level which will light up on the bottom.
Leave it like that until it enters the standby state (it starts flickering).
If the signal intensity reaches the 7th level (displayed on LED levels), you should select buzzer mode by short-pressing the mode\ (M) key.
The longer the intensity indicator is lighting, the closer it is to a possible spying device.
Note that due to the high sensitivity of our top-grade device, cell phone base stations, and other signals can be received when being outdoors.
When searching for a spy device inside your car, we recommend driving somewhere away from the town where the signal is weak. Also, turn off your phone.
It’s possible to receive an alarm when someone is talking on their phone near you or when you’re too close to a wireless router.

Camera Detection

Press the mode (M) key for 3 seconds and the magnetic field (GS) will turn on and enter the standby state.
When you put it near a magnetic field source, the buzzer will Start working by short-pressing the mode (M) key.
Watch the signal intensity indicator to see how close or far You are from some suspicious device.
Go through every part of the room slowly and make sure to check all the corners, ceiling, ventilation, or other popular places where people would position hidden cameras.

If you want to read this user manual in a different language, go to osmousermanual.com.

Have any questions or need further assistance?
Send us an email at support@osmoofficial.net and we will be happy to help!

If you want to read this user manual in a different language, visit osmousermanual.com

Basic Info

The device has a handheld design with an antenna on the top left side and a magnetic probe in the middle. On the right side, there’s a sensitivity adjustment knob. Rotate it clockwise to increase it based on your needs. The left M key is the mode key, the MS lamp is the mode indicator, GS LED is the magnetic indicator. At the bottom, you have a 10-level LED display which indicates how close or far the bug/camera/or other device is. On the right side, you have a charging DC base which will blink while charging. When it’s fully charged, it will stop blinking.

How To Use

RF Signal Detection
Turn on the TopDetect, rotate the sensitivity adjustment knob clockwise to the maximum. You will hear a long beeping sound which means the device entered detection mode. Turn on the TopDetect and adjust the sensitivity knob to the first level which will light up on the bottom. Leave it like that until it enters the standby state (it starts flickering).

If the signal intensity reaches the 7th level (displayed on LED levels), you should select buzzer mode by short-pressing mode (M) key. The longer the intensity indicator is lighting, the closer it is to a possible spying device. Due to the high sensitivity of our top-grade device, cell phone base stations and other signals can be received when being outdoors. When searching for a spy device inside of your car, we recommend driving somewhere away from the town where the signal is weak. Also, turn off the phone. It’s possible to receive an alarm when someone is talking on their phone near you or when you’re too close to the wireless router. Images below show how you should check for spying devices on your car:

Camera Detection

Press the mode (M) key for 3 seconds and the magnetic field (GS) will turn on and enter the standby state. When you put it near the magnetic field source, the buzzer will Start working by short-pressing the mode (M) key. Watch on signal intensity indicator to see how close or far You’re to some suspicious device. Go through every part of the room slowly and make sure to check all the corners, ceiling, ventilation, or other “popular” places where people would position hidden cameras.