OSMO HotSpot VX7 User Manual

OSMO HotSpot VX7

If you want to read this user manual in a different language, please visit osmousermanual.com

Specifications

1. External antenna connectors (not supported by all the devices)
2. Charging/micro-USB jack
3. Indicator light
4. Power key
   • Press and hold for about 3 seconds to power on/off your device.
   • Press and hold for about 10 seconds to restart your device.
5. WPS key Press and hold for 3 seconds to activate the WPS function.
6. micro-SIM card slot and reset hole

Indicator Lights

Battery

Red Solid/Blinking – The battery is low. Please charge the battery. Green Blinking – The battery is being charged. Green Solid – The battery level is middle or high. Lights Off – Your device is not being charged.

Wi-Fi

• Blue Blinking – WPS is active.
• Lights Off – Wi-Fi is off.

SMS

• Blue Solid – You have unread messages
• Blue Blinking – You have new messages
• Lights Off – There is no unread message or new message.

Network

Red
The device is in error status.

• The device is not registered to the mobile network.
• There is no micro-SIM card inserted.
• There is no network service available.

Green Solid
The device is registered to the 2G/3G mobile network.

Green blinking
The device is connected to the 2G/3G mobile network and data is being transferred.

Blue solid
The device is registered to the 4G LTE network.

Blue blinking
The device is connected to the 4G LTE network and data is being transferred.

Installation

1. Open the SIM card slot cover
   NOTE: Do not remove the cover rudely, because it is connected with the device.

2. Install a micro-SIM card to the micro-SIM card slot.This device does not support SIM cards, nano-SIM cards or any other non-standard micro-SIM cards. To avoid damage to the device, do not use those cards or any card holders.

3. Close the micro-SIM card slot cover.

Connecting

Using Wi-Fi

1. Turn on your device
2. Ensure that your computer or other devices have enabled Wi-Fi and search for available networks. NOTE: If you use a computer, you need to set your computer to obtain and IP address automatically.
3. Select the WiFi name (SSID) of your device and click Connect.
4. Enter the WiFi password if required and click OK.
5. Wait until the client device is connected to your device successfully.

Using USB Cable

1.  Connect a computer to your device with an USB cable

2. Turn on your device. The OS detects new hardware and automatically installs new software.
   Note: If the system does not automatically launch installation, you can double-click the device installation icon in My Computer.

3. Wait until the computer is connected to your device successfully.

You can view the label on the device to get the default Wi-Fi SSID and password.

Logging In

1. Ensure that the connection between your device and the client device is active.
2. Launch the internet browser and enter http://192.168.0.1 or http://ufi.ztedevice.com in the address bar
3. Enter the password to log in to the 4G mobile hotspot config page.

NOTE: The default password is admin.

Changing SSID

1. Log in to the 4G Mobile Hotspot Configuration page.
2. Select WiFi settings.
3. Change the Network Name (SSID) or password in main SSID area.
4. Click apply.

Accessing Internet

After a client device is successfully connected to your device, you can access the Internet in Automatic or Manual mode. The default mode is Automatic.

Automatic
Your device is automatically connected to the Internet, and you can surf on the Internet through the client.

Manual

1. Log in to the 4G Mobile Hotspot configuration page
2. In my router section, select LTE (or other network type), Settings > Connection Mode > Manual, and then click Apply.
3. Return to the home page and then turn it on.

Note:

• To modify the parameters of your device, log in to the 4G Mobile Hotspot confguration page.
• To change current connection setting, please disconnect from network.

Configuring PC

1. Right-click Network and select Properties
2. Select Change adapter settings
3. Right-click Wireless Network Connection and select Properties
4. Select Internet Protocol Version 4 (TCP/IPv4), and click Properties
5. Select Obtain an IP address automatically and Obtain DNS server address automatically, and click OK.

Troubleshooting

Precautions

• If inadequately shielded, some electronic devices, for example, the electronic system of vehicles, may be affected by the electromagnetic interference caused by the device. Consult the manufacturers of such devices before using the device if necessary.

• Operating the device may interfere with medical instruments such as hearing aids and pacemakers. Always keep the device more than 20 centimeters away from such medical instruments when your device is powered on. Power off the device if necessary. Consult a physician or the manufacturers of medical instruments before using the device if necessary.

• Be aware of the usage limitation when using
  the device at places such as oil warehouses or chemical factories, where there are explosive gases or explosive products being processed. Power off the device if necessary.

• Do not use electronic transmission devices in aircrafts, at petrol stations or in hospitals. Observe and obey all warning signs, and power off the device in these conditions.

• Do not touch the inner antenna area unless necessary. Otherwise the performance of the device may be affected. Avoid using the device near or inside metallic constructions or establishments that can emit electromagnetic waves, because signal reception may be affected.

• The device is not waterproof. Keep the device dry and store it in a shady and cool place.

• Do not use the device immediately after a sudden temperature change, because dew may be generated inside and outside the device. Do not
  use it until it becomes dry.

• Handle the device carefully. Do not drop, bend or strike it. Otherwise the device may be damaged.

• Only qualifed personnel can dismantle and repair the device.

• The humidity between 5% and 95% are recommended.

• Using ZTE-unapproved or incompatible battery, charger or power adapter may damage your device, shorten its lifespan or cause a fire, explosion or other hazards.

• The recommended operating temperatures are 0 °C to 35 °C and the storage temperatures are -20 °C to +45 °C. Extreme temperatures can damage the device and reduce the charging capacity and lifespan of your device and battery.

If you want to read this user manual in a different language, go to osmousermanual.com

Have any questions or need help?
Send us an email at support@tryosmo.com and we will be happy to assist you!

References

• osmousermanual.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>