HOME DECORATORS COLLECTION N300772-H Roller Shade Instruction Manual
- June 12, 2024
- HOME DECORATORS COLLECTION
Table of Contents
N300772-H Roller Shade
Product Information
The N300772-H Roller Shade is a window covering system that
provides privacy and light control. It can be installed as a single
shade or as a coupled shade system, where two shades are operated
by one control. The roller shade comes with various hardware
components for installation, including shade brackets, screws,
spacer blocks, and optional accessories such as a top light guard
and magnet catch.
Hardware Included
- 1 1/4 Hexagon screw x 2
- Flat head screw x 2
- 3/4 Round head screw x 1
- 5/8 Flat head screw x 1
Recommended Tools
- Screw gun / Drill
- Tape Measure
- Screwdriver
- Level
- Pencil
Usage
The roller shade and its components are used for the following
purposes:
-
To install shade brackets
-
To install safety tension device
-
To install traditional hold down bracket and top light guard
holder -
To install magnet catch (For magnetic hold down)
-
To install top light guard
-
To join the spliced aluminum light guard pre-installed on the
top of the aluminum light guard
Product Usage Instructions
Shade Bracket Installation – Single Shades
-
Remove the tape from the installation template.
-
Place the template on the wall and use it to mark the mounting
hole positions with a pencil. -
Remove the template.
-
Make sure the distance from the template’s front mounting hole
to the front edge of the window frame is at least 3/4″. -
Ensure that the shade brackets line up with each other
horizontally. -
For each shade bracket, use two 1 1/4″ hexagon screws for
installation.
Shade Bracket Installation – Cordless Shades
Note: Do not use the installation template for side
mount.
-
Put the bracket covers over the shade brackets to assemble
them. -
Screw the brackets into the wall.
-
Make sure the distance from the brackets’ front mounting hole
to the front edge of the window frame is at least 3/4″. -
Ensure that the shade brackets line up with each other
horizontally. -
For each shade bracket, use two 1 1/4″ hexagon screws for
installation.
Link System Assembly – Coupled Shades
- Male Drive: Pre-installed into the shade with end plug.
- Female Drive: Pre-installed into the shade with control
side.
-
Step 1: Install the control side into the bracket for the
control side. -
Step 2: Press the female shaft and put it into the opening of
the link bracket. -
Step 3: Insert the male drive into the shaft of the female
drive. -
Step 4: Install the end plug into the bracket for the end plug
side. -
Step 5: Slide down the lock pin into the end plug.
N300772-H
Roller Shade Installation Instructions (Without Top Treatment)
Single Shade
3. Hardware for Coupled Roller Shades
Hardware
Drawing
Usage
Link bracket
Male Drive Female Drive
Installation Template
4. Optional hardware
Coupled Shades Link System Used for coupled shades
Coupled Shades Features two shades operated by one control.
Recommended Tools
Screw gun / Drill Tape Measure Screwdriver Level Pencil
Hardware Included
1. Screws needed for installing
Hardware
Drawing
1 1/4″ Hexagon screw
2″ Flat head screw
3/4″ Round head screw
5/8″ Flat head screw
Usage
To install shade brackets
To install safety tension device To install traditional hold down bracket and
top light guard holder To install magnet catch
Traditional Hold Down Bracket
Magnet Catch (For magnetic hold down)
Spacer Block
5. Hardware for light guard system
Hardware
Drawing
Top light guard holder
Transparent Adhesive Tape
Aluminum light guard end cap
Usage
To install top light guard
To join the spliced aluminum light guard Pre-installed on the top of the
aluminum light guard
6. Mounting Brackets and Spacer Block Qty
Shade Type Single Shades
Shade width Mounting
(X) Brackets Qty
All
2
Spacer Block Qty -1 Layer
2
Spacer Block Qty -2 Layers
4
Coupled Shades
All
3
3
6
Shade Bracket Installation
For Single Shades
Remove the tape from the installation template. Place the template on the wall
and use it to mark the mounting hole positions with a pencil. Then remove the
template. Make sure the distance from the template’s front mounting hole to
the front edge of the window frame is at least 3/4″. The shade brackets must
line up with each other horizontally. Each shade bracket will require two 1
1/4″ hexagon screws for the installation.
3/4″
2. Hardware for single unit Roller Shade
Hardware
Drawing
Usage
Shade bracket
To install shade (on Control Side)
Shade bracket
Bracket cover
Handle
To install shade (on End Plug side)
Shade bracket cover (Pre-installed on the shade bracket)
For Cordless Shades
Inside Mount
Outside Mount
Do not use installation template for side mount. First, put the bracket covers over the shade brackets to assemble them, and then screw the brackets into the wall. Make sure that the distance from the brackets’ front mounting hole to the front edge of the window frame is at least 3/4″. The shade brackets must line up with each other horizontally. Each shade bracket will require two 1 1/4″ hexagon screws for the installation.
3/4″
Installation Template
Used for single shades
Inside-Side Mount
For Coupled Shades
First, place the installation template on the wall and mark the mounting hole
positions with a pencil. Make sure the distance from the template’s front
mounting hole to the front edge of the window frame is at least 3/4″. Then
remove the template. Next, install the brackets. Make sure that the center of
both the link bracket and the shade brackets line up and are level with each
other. Each shade bracket will require two 1 1/4″ hexagon screws for the
installation. Please ensure the link bracket is facing the control side.
Inside Mount
This hole is facing the control side.
Outside Mount
The link bracket is facing the control side.
This hole is facing the control side.
The link bracket is facing the control side.
Link system assembly
Male Drive: Pre-installed into the shade with end plug.
Female Drive: Pre-installed into the shade with control side.
Link system installation: Step 1: Install the control side into the bracket
for the control side. Step 2: Press the female shaft and put it into the
opening of the link
bracket. Step 3: Insert the male drive into the shaft of the female drive.
Step 4: Install the end plug into the bracket for the end plug side. Step 5:
Slide down the lock pin into the end plug.
Shade Bracket installation tips Ensure the right set of shade brackets is
being used. Please note that bracket sizes will vary based on order size.
Make sure the top and bottom of the brackets align on both sides.
Make sure the front and back of the brackets align on both sides.
Shade Installation and Removal
Installation of the Shade First, insert the control side into the tongue of
the bracket for the control side. Second, press the end plug and insert the
end plug into the hole of the bracket on the other side. Third, slide the lock
pin in the end plug bracket downward into the end plug to prevent the shade
from falling.
4 Finally remove the paper band from the shade.
4
3
Align control side of the shade with the tongue of the bracket for the control side.
Slide the lock pin in the shade bracket downward into the end plug to prevent the shade from falling.
Shade installation tips: After shade is installed into shade brackets, use a level to check if the fabric roll is horizontal; if not, please adjust the position of shade brackets to keep the fabric roll level.
The shade needs to be level.
The gap on the end plug side
Removal of the Shade
needs to be about 3/16″.
Use a tool to push the lock pin on the end plug bracket upward.
Use tool to draw back the end plug from bracket.
Finally, remove shade from mounting bracket on the other side.
Continuous Cordloop Installation
Install Safety Tension Device Use two 2″ flat head screws to install the
safety device. The beaded chain should be fully extended upon installation of
the device.
1/2
N300772-H
Hold Down Bracket Installation (optional) A. Traditional Hold Down Bracket Use
3/4″ round head screw to secure each bracket.
Remove handle from hem bar Use a flat head screwdriver to pry the bottom of the handle from the hem bar.
Motorized Operation
All motorized shades are pre-programmed before shipping. Operating channel
numbers have been pre-set based on the customer’s request. All units can also
be controlled via Channel “0”.
B. Magnetic Hold Down Use 5/8″ flat head screw to secure the magnet catch at
the below location. Make sure the magnet catch aligns with the pre-installed
magnet on shade bottom rail.
Side edge of the shade
9/16″
Bottom edge of the shade
Continuous Cord Loop Operation
11/16″
To release or lower the shade, pull downward on the beaded chain that is closest to the shade fabric.
To raise the shade, pull downward on the beaded chain that is farthest away from the shade fabric.
Cordless Installation
Handle Installation and Removal Attach Handle to Hem Bar Step one: Turn over
hem bar and take notice of the label attached at the
center. Step two: Align the center of the bottom handle with the label. Step
three: Hook the handle to the hem bar beginning at the top, and then click the
handle into place at the bottom of the hem bar. Step four: Remove the label
from hem bar.
Label
2
The center of handle should be aligned with the label.
3
4
5
Cordless Operation
Pull the handle downwards or upwards and the shade will be lowered or raised.
The tension in our cordless roller shades can be adjusted to provide optimal
light control and to ensure easy and dependable operation on a variety of
window types and sizes. If a cordless shade begins to slide down on its own or
it fails to roll up, the issue can be easily fixed by turning the adjustment
dial towards “+” to increase the tension.
Conversely, if the cordless shade cannot stop at the desired height and tends
to roll up by itself, the tension can be decreased by turning the adjustment
dial towards the “-“.
The shade must be installed on the brackets when adjusting.
Place the U-shaped channel of pole under the handle and push up to lift the shade.
Use the “hook” portion to hook the handle to lower the shade.
Motorized Installation
Battery Wand Installation
Battery wands for motorization can be easily installed horizontally or
vertically using the battery wand clips. Simply line the clips up in a
straight line and snap battery wand into place.
Up Stop Down Channel select
Installation of Light Guard System
Light Guard System drawing
Top light guard holder
Top Light Guard
End
Cap
3/4″ Round head screw
Transparent Adhesive Tape
Side Light Guard
Installation of Top Light Guard
Install top light guard holders
Each top light guard holder needs one 3/4″ round head screw for installation.
This part can be broken off if needed.
Spaceevenly Spaceevenly
Install Top Light Guard
Insert top light guard into the back of the top light guard holders, and make
sure the top light guard meets the top of the window firmly.
Vertical
Horizontal
Installation of Side Light Guard
Fully lower the shade and place the wider side of the light guard next
to the back of the shade fabric.
Tear off the double-sided tape on the narrow side, and stick the light
guard to the window frame.
For better light blocking, the top of the light guard should be placed
next to the shade fabric, and the bottom of the light guard should be sloping,
or angled, toward the front.
Installed vertically
Installed sloping
Installation of Transparent Adhesive Tape
Transparent adhesive tape is included for aluminum light guard length >96″ and
spliced into 2 parts.
Installation: Align the double dotted line with the edge of the light guard,
and fold the transparent adhesive tape on both sides, as shown in the figure
below.
Transparent adhesive tape
Left
Right
Left
Right
How to Care for Your Shades
Dusting: Regular light dusting with a feather duster is recommended. Do NOT
wash or use strong detergents and spot removers. Dry cleaning is not
recommended. Vacuuming: Use a hand-held vacuum with low suction for more
thorough dust removal. CAUTION: DO NOT use abrasive or harsh chemicals which
will damage the surface of the shade. Be careful not to bend the fabric while
cleaning.
Need Assistance?
Customer service is available by calling
1-855-558-1222 or send an email to
help@venetawindowfashions.com.
2/2
N300774-G
Roller Shade Installation Instructions (With Top Treatment)
Square Fascia end cap
Curved Fascia end cap
Valance return connector
Handle
For Square Fascia
Inside Mount:
For Curved Fascia
To connect fabric valance returns
For Cordless Shades
Outside Mount:
Removal of Shade
Use a tool to push back the front or back plastic part of the brackets, and
then turn the back side of the raceway downward so that it detaches from the
brackets. Finally, remove the raceway by pulling it downward from the
brackets.
Single Fascia
Common Fascia
Cover two individual shades with one top treatment
Recommended Tools Screw gun / Drill Tape Measure Screwdriver Level Pencil
Hardware Included
1. Screws needed for installing
Hardware
Drawing
1 1/4″ Hexagon screw
2″ Flat head screw 3/4″ Round head screw 5/8″ Flat head screw
2. Hardware for Roller Shade
Hardware
Drawing
Mounting Bracket
Valance bracket
Valance clip
Usage
To install shade brackets
To install safety tension device To install traditional hold down bracket To
install magnet catch
Usage To install raceway (for inside mount)
To install raceway (for outside mount)
To install fascia / valance (mounted on raceway)
To install fascia / valance (placed on fascia/valance)
3. Optional hardware
Traditional Hold Down Bracket
Magnet Catch (For magnetic hold down)
Spacer Block
4. Hardware for light guard system
Hardware
Drawing
Usage
Transparent Adhesive
Tape
To join the spliced aluminum light guard
Aluminum light guard
end cap
Pre-installed on the top of the aluminum light guard
5. Mounting Brackets and Spacer Block Qty
Shade Type
Shade width (X)
Mounting Brackets
Qty
Spacer Block Qty -1 Layer
Spacer Block Qty -2 Layers
8″ X 40″
2
2
4
Single Shades /
40″<X 80″
3
3
6
Dual Shades
X>80″
4
4
8
Shades Installation and Removal
Installation of mounting brackets
When installing the mounting bracket, the distance from the bracket’s front
mounting hole to the front edge of the window frame should be at least 3/4″.
Make sure all brackets line up with each other horizontally. Each bracket will
require two 1 1/4″ hexagon screws for the installation.
Brackets position:
Installation of shade There are two methods of installation. 1. Insert the
back edge of the raceway into the back plastic part of the bracket, and then
turn the raceway upwards so that the front rib of the raceway snaps into the
bracket.
1
2
2. Snap the front rib of the raceway into the bracket, and then turn the
raceway backwards and upwards so that the back of the raceway is stuck to the
back plastic part of the bracket.
1
Continuous Cordloop Installation
Install Safety Tension Device Use two 2″ flat head screws to install the
safety device. The beaded chain should be fully extended upon installation of
the device.
Hold Down Bracket Installation (optional) A. Traditional Hold Down Bracket Use
3/4″ round head screw to secure each bracket.
B. Magnetic Hold Down Use 5/8″ flat head screw to secure the magnet catch at
the below location. Make sure the magnet catch aligns with the pre-installed
magnet on shade bottom rail.
Side edge of the shade
9/16″
Bottom edge of the shade
11/16″
2
1/3
N300774-G Continuous Cord Loop Operation
To release or lower the shade, pull downward on the beaded chain that is closest to the shade fabric.
To raise the shade, pull downward on the beaded chain that is farthest away from the shade fabric.
Cordless Installation
Handle Installation and Removal
Attach Handle to Hem Bar Step one: Turn over hem bar and take notice of the label attached at the
center.
Step two: Align the center of the bottom handle with the label. Step three: Hook the handle to the hem bar beginning at the top, and then
click the handle into place at the bottom of the hem bar.
Step four: Remove the label from hem bar.
1
Label
Cordless Operation
Pull the handle downwards or upwards and the shade will be lowered or raised.
The tension in our cordless roller shades can be adjusted to provide optimal
light control and to ensure easy and dependable operation on a variety of
window types and sizes. If a cordless shade begins to slide down on its own or
it fails to roll up, the issue can be easily fixed by turning the adjustment
dial towards “+” to increase the tension.
Conversely, if the cordless shade cannot stop at the desired height and tends
to roll up by itself, the tension can be decreased by turning the adjustment
dial towards the “-“.
The shade must be installed on the
brackets when adjusting.
Place the U-shaped channel of pole under the handle and push up to lift the shade.
Use the “hook” portion to hook the handle to lower the shade.
Up
Stop Down
Channel select
Fascia & Valance Installation
Valance Bracket Installation Install the fascia or the valance after the shade
is mounted. Align the valance bracket with the raceway first. And then push
the bracket onto the raceway. The top groove of the valance bracket should
hook onto the top of the raceway while the bracket’s bottom groove clips into
the bottom rib of the raceway, as shown below. Valance Bracket on Raceway:
The drawing below shows the valance brackets installed in an ideal position.
They are placed far enough apart so that the space is divided evenly.
For Fabric Valance (Dual Shades only): The direction of this valance clip is
facing downward.
Attach Fascia End Cap to Fascia
Optional: Attach Fabric Valance Return to Valance Insert valance return
connector to return. Then attach return to valance.
2
Motorized Installation
Battery Wand Installation
Attach Valance/Fascia to Raceway
The center of handle should
Battery wands for motorization can be easily installed horizontally or
Valance Clip Installation
Slide the valance clips to a position on the valance/fascia so that they are each aligned with a valance bracket on the raceway, and then push the
be aligned with the label.
vertically using the battery wand clips. Simply line the clips up in a straight line and snap battery wand into place.
Insert the valance clip into the dedicated groove on the aluminum strip,
valance clips into the valance bracket.
paying special attention to the direction the valance clip. Valance clips
3
4
5
should face upward for a fascia. For a fabric valance, valance clips
For Fascia:
should face downward. The valance clip location should align with the
valance bracket as pictured below.
For Fascia:
Remove handle from hem bar Use a flat head screwdriver to pry the bottom of the handle from the hem bar.
Vertical
Horizontal
Motorized Operation
All motorized shades are pre-programmed before shipping. Operating channel
numbers have been pre-set based on the customer’s request. All units can also
be controlled via Channel “0”.
The direction of this valance clip is facing upward.
For Fabric Valance:
2/3
N300774-G
Fascia Keystone Installation Keystones are for fascias that require splicing.
Keystone for Curved Fascia with Fabric Insert
Velcro Velcro
Curved fascia connector
Method 2 Suggested for semi-inside mount and outside mount. Place the keystone onto the joint where the two valance pieces meet, and hook the top of the keystone around the top edges of the fascia. Then push the bottom edge of the keystone into the bottom edges of the fascia, as shown in the drawing below.
Installation of Top Light Guard Insert the top light guard into the back groove of mounting brackets.
Wrapped fabric
- Align left and right fascia, and then slip the fascia connector from left fascia to right fascia, as shown in drawing.
- Attach the Velcro on the top back of the wide side of the keystone to the fascia connector, as shown in drawing.
- Finally, wrap the keystone to the front of the fascia, from the bottom edge of the fascia to the back, and attach the Velcro to the lower part of the fascia connector, as shown in drawing.
Valance/Fascia Removal
First, remove valance/fascia with valance clips from the valance brackets.
Installation of Side Light Guard
F u l l y lower the shade and place the wider side of the light guard next
to the back of the shade fabric.
T e a r off the double-sided tape on the narrow side, and stick the light
guard to the window frame.
F o r better light blocking, the top of the light guard should be placed
next to the shade fabric, and the bottom of the light guard should be sloping,
or angled, toward the front.
How to Care for Your Shades
Dusting: Regular light dusting with a feather duster is recommended. Do NOT
wash or use strong detergents and spot removers. Dry cleaning is not
recommended. Vacuuming: Use a hand-held vacuum with low suction for more
thorough dust removal. CAUTION: DO NOT use abrasive or harsh chemicals which
will damage the surface of the shade. Be careful not to bend the fabric while
cleaning.
Need Assistance?
Customer service is available by calling
1-855-558-1222 or send an email to
help@venetawindowfashions.com.
Keystone for Square Fascia
There are two connecting methods. Method 1 Recommended for inside mount.
Insert the left & right fascias into the keystone, as shown in the drawing
below.
Take shade down from mounting brackets before removing valance brackets from
the raceway.
Turn the valance brackets 90 degrees, and then take the brackets off of the
raceway, as shown in the drawing below.
Note: The installation & removal for all fascias & valances are the same.
Installed vertically
Installed sloping
Installation of Transparent Adhesive Tape Transparent adhesive tape is
included for aluminum light guard length >96″ and spliced into 2 parts.
Installation: Align the double dotted line with the edge of the light guard,
and fold the transparent adhesive tape on both sides, as shown in the figure
below.
Installation of Light Guard System
Top Light Guard
Transparent adhesive tape
Side Light Guard
Left
Right
Left
Right
Back
Front
3/3
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>