CHERUBINI GIRO Remote Control Instruction Manual
- June 12, 2024
- Cherubini
Table of Contents
Made by
via Adige, 55 – 25081 – Bedizzole (BS) – Italia
www.cherubini.it
Rev: 04 01/2021 – Cod: A4518_6D17
GIRO
GIRO Lux
ISTRUZIONI PER L’USO – INSTRUCTION FOR USE
DESCRIPTION
– The remote control is compatible with all the ‘CRC – CHERUBINI REMOTE CONTROL’ branded components (fig. 4). With this remote control, it is possible to control one or more receivers at same time. To operate, the remote control needs to be programmed to the appropriate receiver(s).
POWER SUPPLY
– The remote controls GIRO work with two 1.5 V Alkali batteries (AAA) format
LR03 (fig. 3). White front LED will be lightened during transmission. (GIRO
fig. 1) or the display (GIRO LUX fig. 2) – will be on if batteries are
charged, blinking when batteries are low. Replace the batteries only with the
same type.
**** Hereby, Cherubini S.p.A. declares that the radio equipment type remote
controller GIRO is in compliance with the Directive 2014/53/EU, Directive
2011/65/EU.
The full text of the EU declaration of conformity is available upon request at
the following website: www.cherubini.it.
GUARANTEE
Failure to comply with these instructions annuls CHERUBINI’s responsibilities and guarantee.
TECHNICAL FEATURES
| GIRO| GIRO Lux
---|---|---
Power supply| 2,4 V – 3 V DC| 2,4 V – 3 V DC
Type of battery| 2 x LR03 (AAA)| 2 x LR03 (AAA)
Transmission frequency| 433,92 MHz| 433,92 MHz
Modulation| AM / ASK| AM / ASK
Decoder system| Rolling Code| Rolling Code
Irradiated RF power (ERP)| 3 mW| 3 mW
Operating range in open space| 150 m| 150 m
Operating temperature| -10°C +50°| -10°C +50°
Dimensions (mm)| 160 x Ø30| 160 x Ø30
Weight (with batteries)| 100 g| 100 g
SIMBOLOGIA
GIRO (fig. 1)
LED white – transmission operating.
Blinking when battery is discharging.
GIRO Lux (fig. 2)
– Activating the Sun-sensor (Lux)
Deactivating the Sun-sensor (Lux)
DISPLAY
Transmission operating, blinking when battery is discharging.
Wind-sensor is “ON
Sun-sensor
SIMBOLOGIA
GIRO Plus (fig. 1)
Change channel +
DISPLAY
Transmission operating,
GIRO P-Lux (fig. 2)
Change channel
Wind-sensor is “ON”
Sun-sensor is “ON”
Restriction of the number of channels
Select the last channel in use (N).
The display will show available channels (from 1 to N) in rapid succession.
Function clearing:
This function allows you to exclude temporarily from the selection all channels not in use.
CAUTION: Risk of explosion if battery is replaced by an incorrect type.
Used batteries should be disposed of responsibly.
LEGENDA
T1 First remote control to be set
Tn Already programmed remote control
Tx Additional remote control
To set the remote control use the A-B-C buttons sited in the battery slot.
(fig.5).
FUNCTION OPEN/CLOSE PROGRAMMING –
To prevent accidental changes to the programming of the motor during the daily
use of the remote control, the possibility of programming is disabled
automatically 8 hours after sending the last sequence (A+B or B+C).
– Checking the status of the function 
To change the status of the function, see the sequences “enable/disable
programming”
Enable programming
Proceed with programming as the instructions booklet
– Disable programming
GIRO Lux – LUX function
Tn
Push and release.
To activate push for min. 3 sec.
To deactivate push for min. 3 sec.
Warning!
Before setting for the first time read the instructions for the motor and/or
the receiver.
Installatore
Documents / Resources
|
CHERUBINI GIRO Remote
Control
[pdf] Instruction Manual
GIRO, GIRO Lux, GIRO Remote Control, Remote Control, GIRO Plus, GIRO P-Lux
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>