BOYO VTCRH2 Wireless AHD Magnetic Mount Vehicle Backup Camera System User Manual
- June 12, 2024
- BOYO
Table of Contents
**BOYO VTCRH2 Wireless AHD Magnetic Mount Vehicle Backup Camera System User Manual
**
Accessories
DC5.5 power cablee2PCS
(3PCS for VTCRH2 and
5PCS for VTCRH4)| Fan-shaped bracket •1PC| Car charger power p
g
cable • 1 PC| 2.4GHz 50B antenna ‘2PCS (3PCS for VTCRH2. 5PCSfor VTCRH4)
---|---|---|---
| | ***|
2.4GHz antenna extension
cord•1PC| 2.4GHz wireless cameras
•1PC (2PCS for VTCRH2.4PCS for VTCRH4)| Power adapter1PC| Suction bracket1PC
| | |
Warranty card 1PC
| Product registration card1PC
|
For technical support contact 838-941-3060 or email [email protected] WWW.VISIONTECHAMERICA.COM
Notice to the VICRH hitch camera installers
- When installing, please install it in the position permitted by laws and regulations, and we shall not be responsible for the liability caused by the illegal installation and use of the product.
Notice to the VTCRH hitch camera users
- In cold weather, the monitor may display a dark screen at startup As the unit warms up, the display wil return to a normal bright display with the increase in temperature.
- For your safety, do not watch the video or set monitors while driving
- Please do not disassemble the monitor or the cameras, non-sir- vice able parts inside and will avoid warranty.
The cameras are battery-operated and have a built-in rechargeable battery. Once fully charged, it will operate continuously for 20 hours. The battery can be charged using
If you are planning to operate the hitch cameras for multiple days, please consider the following to conserve battery.
- turn off the power to the camera when not using.
- install a DC power cable near the camera to ACC power and connect it to the camera. It will charge the battery while the vehicle key is on.
Product Features
- Heavy duty wireless camera with IR night vision, built-in battery and magnetic mounting. 3MP camera 720P HD video streaming. Camera operates for 20 hours with full charge.
- 5″ IPS display monitor with full viewing angle.
- 1024*800 high-resolution with 16:9 wide-screen display.
- Automatically shut off screen when there is no video signal and quick start-up within a second when signal is detected.
- Transmission distance up to 700ft.
Product Introduction
Monitor Introduction
- 2.4GHz transmission antenna
- LCD screen
- M Menu: enter exit the menu
- Flip: horizontally/vertically image flip
- Power: turn on/off the display
- Parking Guidelines: on/off
- Paring: long press to pair 34567 press shortly to switch display (2Ch & 4Ch)
Wireless Camera Introduction
- 2.4GHz antenna
- Night vision infrared light
- Angle adjusting knob
- Light sensor(night vision)
- Power indicator
- Power on/off
- Buiilt-in battery H
- Charging port
Menu Setup Introduction
Display Settings
Press the “M” menu button to adjust display contrast, saturation and
brightness. Press “ 4n” or “4 2″ button to increase or decrease the contrast,
saturation or brightness. New settings will be saved and options will
disappeared automatically after 5 seconds of idle time.
Flip Image
Under single image display, press “.ax” key on the front panel to turn
up/down/leftright the display image.
Under multiple image split screen display, turn up/down/leftiright the screen and menu (only for VTCRH2 and VTCRH4)
Parking guideline On/Off
Press “42″ button to display or hide the parking guidelines.
Change Display Mode (VTCRH2 and VTCRH4)
Press “ap” to switch between camera displays.
Camera Pairing
Under single camera display mode,
-
Press and hold “ap” key on the front panel to pair the cameras.
-
Tum camera power off.
-
Turn camera power on to pair. If pair successfully, it will show the camera image.
If not, then the screen wil display “Pair fail”. Repeat the steps to re-pair.
Connections
Wireless camera
Charged by cigarette car charger
Powered by DC power cable
Wireless monitor
VTCRH1 Wireless Monitor
12~24VDC Power: via cigarette car charger or via DC cable Trigger Wire: Green
wire: triggers CAM1 to full screen
VTCRH2 Wireless Monitor
12~24VDC Power: via cigarette car charger or via DC cable Trigger Wires: Brown
wire: triggers CAMT to full screen Green wire: triggers CAM2 to full screen
VTCRH2 Wireless Monitor
12-24VDC Power:
via cigarette car charger or via DC cable
Trigger Wires :
- Brown wire: triggers CAM1 to full screen
- Green wire: triggers CAMZ to full screen
- Blue wire: ~triggers CAMS to full screen
- Gray wire: triggers CAM4 to full screen
Product Function & Parameter
Wireless Monitor
- LCD: 5 inch IPS panel, 16:9 high definition
- Resolution: 1024RGB800
- Full viewing angle: Left(85°) Right(85°) Below(85°) Above(85°)
- Panel key function: 5PCS key control
- Wireless video input: 1, 2, or 4 channel wireless video input
- Using digital wireless encryption technology to code connection, with strong anti-interference ability
- 2.4GHzwireless transmission distance: 700ft
- Power supply: DC12-24V
- Power consumption: 3W
- Working temperature: -4°F ~ 158°F
- Storage temperature: -22°F ~ 185°F
- Size: 56″ x 4.1″ x 25″ (excluding bracket)
Wireless Camera
- Effective resolution: 1280*720px, 720P,
- Image Sensor: 1/2.7″ CMOS
- Horizontal viewing angle: 130 degree
- Wireless transmission distance: 700ft .
- System: PALINTSC automatically .
- SPSP: FHSS(adaptive frequency hopping) .
- Transmission bandwidth: 8MHz BER<1E-3 .
- Built-in battery capacity: 6400mAh .
- Battery indicator: 4 LED lights
- Battery charging time: DC5.5, 5~24V, 10 hours
- Working time: 20 hours(when fully charged) . Camera adjustable angle: 0-100 degree
- Operation frequency: 2400-2483.5MHZ . ON/OFF mode: press and hold to turn on and turn off, short display battery capacity
- Installation mode: magnet base adsorption installation
- Night vision: HD infrared night vision
- SNR: 46.50B
- Waterproof level: IP68
- Transmitting sensitivity: -89 dBm
- Material: black aluminum alloy
- Shockproof: 4G
- Power supply: DC12-24V
- Working temperature: -4°F ~ 158°F
- Storage temperature: -22°F ~ 185°F
- Size: 2.9″ x 1.8″ x 2.2″ (excluding bracket)