TOOL FRANCE TFD-30TE Drill Press User Manual

Drill Press

ORIGINAL MANUAL

France
TOOL FRANCE S.A.S
9 Rue des Pyrénées, 91090 LISSES, France
www.promac.fr

TFD-30TE Drill Press

CE-Conformity Declaration

Product : Drill Press
TFD-30TE
Brand: TOOL FRANCE
Manufacturer or authorized representative
TOOL FRANCE S.A.S
9 Rue des Pyrénées, 91090 LISSES, France
We hereby declare that this product complies with the regulation s
2022/42/EC
Machinery Directive
2014/30/EU
electromagnetic compatibility
designed in consideration of the standards
EN ISO 12100 :2010
EN 12717 : 2001+A1 : 2009
EN 60204-1 :2006+A1 : 2009+AC :2010
EN 61000-6-2:2005
EN61000-6-4:2007+A1:2011
Responsible for the Documentation
TOOL FRANCE S.A.S

2022 – 11 – 01 Cédric Gental, General Manager
TOOL FRANCE S.A.S
9 Rue des Pyrén ées, 91 090 LISSES, France
UK Declaration of Conformity
Product: DRILL PRESS
Model: TFD-30TE
Brand: TOOL FRANCE
Manufacturer or authorized representative:
TOOL FRANCE S.A.S
Unit 1a Stepnell Park
Off Lawford Road
Rugby
CV21 2UX
United Kingdom
We hereby declare that this product complies with the regulations: Supply of Machinery (Safety) Regulations 2008
Electromagnetic Compatibility Regulations 2016

designed in consideration of the standards:
EN ISO 12100 :2010
EN 12717 : 2001+A1 : 2009
EN 60204-1 :2006+A1 : 2009+AC :2010
EN 61000-6-2:2005
EN61000-6-4:2007+A1:2011
Responsible for the Documentation:
TOOL FRANCE S.A.S

2022 – 11 – 01 Cédric Gental, General Manager
TOOL FRANCE S.A.S
9 Rue des Pyrén ées, 91 090 LISSES, France

General safety rules

Note: Non-observance of these instructions may cause serious injury to have consequences.
As with all machines, dangers may occur when operating and handling this machine. Safe operation and correct handling of the machine considerably reduce possible risks of accidents. If the normal precautionary measures are disregarded, accident risks for the operator are inevitable.
The machine was designed only for the given types of use. We strongly advise you not to modify the machine or operate it in a way for which it was not designed.
If you have any questions about the operation of this machine, please contact your dealer first, who will be able to advise you if the Operating Instructions do not provide any clarification.

GENERAL RULES FOR THE SAFE USE OF THE EQUIPMENT

1. For your own safety, always read the operating instructions before starting up the machine, in order to know the machine, its operation and operating limits, and recognise its specific dangers.
2. Keep protective covers in working order and do not remove them.
3. Always connect electrically operated machines with a mains plug with protective contact to a socket with protective contact (earth). If intermediate plugs without earthing contact are used, the earthing contact connection to the machine must be established. Never operate the machine if it is not electrically grounded.
4. Always take out removable clamping levers or keys from the machine. Always check that all removable parts/elements have been removed before switching on the machine.
5. Keep work area free of obstacles. Incorrectly adjusted work areas and work surfaces are a real cause of accidents.
6. Do not operate the machine in hazardous environments. Do not operate the driven machine in damp or wet rooms or expose it to rain. The lighting of work surfaces and areas must be adequate.
7. Keep children and visitors away from the machine. Always keep children and visitors at a safe distance from the work area.
8. Secure the workshop or workroom against unauthorised access. Install child locks in the form of lockable bolts, lockable main switches, etc.
9. Do not overload the machine. The performance of the machine will be improved and its operation safer if it is operated in the performance ranges for which it is designed.
10. Do not use attachments for work for which they are not designed.
11. Wear proper work clothing; avoid loose clothing, gloves, scarves, rings, necklaces, hand chains or other jewellery. These could get caught in moving machine parts. Wear shoes with non-slip soles. Wear a headgear that completely covers long hair.
12. Always wear protective goggles. Proceed in accordance with the accident prevention regulations. Also wear a dust mask when working with dust.
13. Clamp workpieces. Always use a vice or clamping device to hold the workpiece. This is safer than using your hand and both hands are free to operate the machine.
14. Pay attention to stability. Always keep your feet and physical balance in such a way as to ensure that you stand securely.
15. Always keep the machine in perfect condition. To do this, keep the cutting surfaces sharp and clean for optimum performance. Follow the operating instructions for cleaning, lubricating and changing accessory equipment.
16. Always disconnect the machine from the mains before carrying out maintenance work or changing machine parts such as drills, etc.
17. Only use the recommended accessories. Follow the instructions in the User Manual. The use of unsuitable accessories may result in accidents.
18. Avoid unintentional start-up. Before connection to the mains, always check that the operating switch is in the “0” (off) position.
19. Never get on the machine. Serious injury is possible if the machine tips over or comes into contact with the cutting tool.
20. Check defective machine parts. Damaged guards or other parts should be properly repaired or replaced before further use.
21. Never leave the machine unattended during operation. Always switch off the mains supply. Do not leave the machine until it has come to a complete standstill.
22. Never operate the machine under the influence of alcohol, medication or drugs.
23. Ensure that the machine is disconnected from the mains supply before working on the electrical system, on the motor etc.

Work safety-related instructions

Transport of the machine

1. The model TFD-30TE weighs up to 216kg.
2. Use suitable means to transport the machine.
3. The centre of gravity of the machine is very high, take care: there is a danger of tipping over during transport!

Workplace

1. The lighting and ventilation of the workroom must be adequate.
2. The lighting for safe working needs to be 300 LUX.

Mandatory: always wear safety glasses!

Noise level
According to point 1.7.4f of the Machinery Directive 2006/42/EC 4 measurements of the machine were made during idle run mode:
– The microphone was mounted on the operator’s head at a medium height.
– The continuous noise level was below 70 dB (A).
– The instantaneous C-weighted sound pressure measured was always below 130 dB.

NOTE: When the machine is running, the noise level will vary depending on the materials being machined. Therefore, the user will have to assess the intensity and provide, if necessary, the personnel with ear protections according to the terms of the D.L. vo277/1991.

Electrical mains connection

1. The machine model TFD-30TE is supplied with a power cable without plug, 400V, 50Hz. The connections as well as changes to the mains connection must be carried out by a specialist in accordance with standard EN60204-1, section 5.3.
2. The fuse must be at least 10 A.
3. The exact electrical data can be found on the machine’s type plate and the electrical diagram, enclosed with these instructions.
4. ATTENTION: For all service or change-over work and repairs, the machine must be disconnected from the electrical mains (pull out the plug).

The yellow/green earth cable is important for electrical safety. It is therefore important to make sure that the installation is correct.

Technical data

Model …………………………………………………………… TFD-30TE
Drilling capacity, steel (mm) …………………………………………………… 31.75
Motor (Volt) ………………………………………………………………………………. 400
Motor (kW) ………………………………………………………………………………. 0.75
Rotation speeds (rpm) ……………………………. 105 – 2650 (18-speed motor)
Spindle stroke (mm) ………………………………………………………………….. 125
Spindle cone (MT) ………………………………………………………………………… 3
Spindle diameter (mm) …………………………………………………………………. 62
Column diameter (mm) ……………………………………………………………….. 92
Table size (mm) ………………………………………………………………… 390 x 290
T-slot width (mm) ………………………………………………………………………… 12
Overall dimensions (max – H x W xDT, in mm) …………1745 x 450 x 750
Weight (kg) ………………………………………………………………………………. 216

Machine description

With the PROMAC drilling machines, you have universal machining centres at your disposal enabling to carry out the most varied machining operations. Safe working operation and high working accuracy are guaranteed for many years, as long as the machine is correctly used and maintained. The machine should be put into operation only after having carefully read and understood these operating instructions, and only if all the operations involved in its correct use are safely understood and mastered.
To do this, the different functions should be discovered without starting the machine.

Features

1. The design of this machine enables drilling with the most various tools. The machine is equipped with stepped pulleys and with belts for changing the spindle speed.
2. The machine is precision engineered and easy to operate, and provides therefore experienced operators no limits to its use.
3. The drilling process can be done with the following method: Direct manual control of the spindle stroke movement (up movement) for the drilling process.
4. The large dimensioned column gives the machine a high rigidity to prevent any distortion and ensures high accuracy.
5. The machine head is made of solid grey cast iron, and ensures that the accuracy, which is given by precision drilling operations, is maintained.

Handling procedure
To move the drill press, please follow the scheme on the right showing how the machine should be gripped to avoid tipping over.

Electrical diagram
The electrical diagram, 400V/50/3, contains the necessary information for the correct connection of your machine to the mains. If the mains connection (plug) is changed or other operations are made, these must be carried out by a specialist.

Electrical parts list

Abbreviation| Function| Technical feattres| Qty..| Comments
---|---|---|---|---
M1| Motor| 0.75kW / 400V / 3ph / 50Hz| 1| EN60204
M2| Pump motor| 0.1 kW /400V/ 3ph / 50Hz| 1| EN60204
XP| Terminal block| AC400V / 15A| 1| VDE 0606
FU| Fuse| 400V / 4A| 3|
KA1| Relay| 40W / 2.8A| 1| EN60947-4-1
SQ/SQ1| Micro switch| 400V / 10A| 2|
SB1| Start switch| 600V / 10A| 1|
SB2| Emergency stop button| 600V/ 10A| 1|
SB3| Pump switch| 600V / 10A| 1|
| Power cable| AC400V / 16A
3G / 1.25rnm2| 1| VDE0620 H05VVF
| Control cable| AC 230V / 6A 0.3mm2/ T105°C| 1| VDE 0620 HO5VVF
E| Earth connection| | |

TWIST DRILLS

ROTATION SPEED
For drills in high-speed steel, depending on the diameter Steel 35 – 45 kg

MATERIAL
ROTATIVE SPEED RP.M.| Cast iron| Steel| Iron| ALUMINIUM| BRONZE
---|---|---|---|---|---
DRILL DtA(MM)
3| 2550| 1600| 2230| 9500| 8000
4| 1900| 1200| 1680| 7200| 6000
5| 1530| 955| 1340| 5700| 4800
6| 1270| 800| 1100| 4800| 4000
7| 1090| 680| 960| 4100| 3400
8| 960| 600| 840| 3600| 3000
9| 850| 530| 740| 3200| 2650
10| 765| 480| 670| 2860| 2400
11| 700| 435| 610| 2600| 2170
12| 640| 400| 560| 2400| 2000
13| 590| 370| 515| 2200| 1840
14| 545| 340| 480| 2000| 1700
16| 480| 300| 420| 1800| 1500
18| 425| 265| 370| 1600| 1300
20| 380| 240| 335| 1400| 1200
22| 350| 220| 305| 1300| 1100
25| 305| 190| 270| 1150| 950

Main operating elements

1. Start switch (ON)
2. Stop button
3. Pump switch
4. Emergency stop button
5. Speed selector
6. Digital display

Machine installation

The minimum requirements of the premises for the installation of the machine are the following:
– Mains voltage and frequency according to machine’s motor data.
– Ambient temperature from – 10°C to + 50°C.
– Relative humidity not more than 90%.

Anchoring of the machine
The machine is to be placed on a solid cement base at a distance of at least 800mm from the rear wall and anchored to the ground by means of screws and expansion plugs or embedded tie rods. Attention must be paid to levelling.

Assembly of the machine

1. Clamp the worktable to the column.
2. Mount the machine in a place with an even temperature. Ensure that the machine is not exposed to sunlight at the place of installation. Otherwise there is a risk of distortion and loss of accuracy.
3. Check that the motor rotates clockwise before final connection via a plug to the power supply system.
4. The machine must be mounted on a stable and steady base.
5. The machine base has four holes for the fixing screws. Before tightening the screws, check that the clamping table is aligned in the longitudinal and transverse direction with respect to the rotating work spindle. To do this, insert a dial gauge with 1/1000 reading, and align the table accordingly. For alignment, metal sheets of suitable thickness must be wedged between the mounting level and the machine base.

Cleaning and lubrication of the new machine
For transport, the bare surfaces of the machine are protected against corrosion with grease. This grease must be completely removed before putting the machine into operation. Either petroleum or benzine should be used for this purpose.
Note: Do not use paint thinners or similar, otherwise the coating on the press will be destroyed. Make sure that no solvents or greases get onto rubber or plastic parts.
After cleaning, all bare parts should be coated with an oil film using a medium viscosity oil such as PROMAC Art. 100385.

Cooling lubricant
The machine is equipped with a coolant system.
We recommend the biological cooling lubricant PROMAC Art. 9197, pack of 5kg.

PREPARATIONS FOR OPERATION
Check all parts of the machine for perfect condition and function before commissioning. If the safety precautions appropriate to the machine and the machine operation are observed, the accuracy of the machine is guaranteed for a long time.

Always wear safety glasses!

AFTER OPERATION
a) Switch off the machine and disconnect it from the mains.
b) Unclamp the tool.
c) Clean the machine, oil bare parts, guides and spindles.
d) Cover the machine with a cloth to protect it from dust and dirt.

SETTING AND ADJUSTMENT OF THE WORKTABLE
a) To raise or lower the worktable, release the clamping lever. Now the table can be raised and lowered on the column over the rack.
Once the desired height has been reached, the clamping lever must be tightened again to prevent vibration avoid.
b) The worktable can be rotated 360° after loosening the clamping screw. After setting the desired angular position, the clamping screw must be tightened again.

SETTINGS FOR DRILLING
a) Set the drilling depth using the depth stop.
b) The feed for drilling is now done by turning the star knob.

Speed setting

The desired speed can be set by changing the positioning of the belts.
Thanks to its 18-speed motor, the TFD-30TE model has 18 speeds per V-belt position. Proceed as follows:

1. Switch off the machine.
2. Open the V-belt cover.
3. Loosen the set screws (30).
4. Press the motor against the head housing using the lever (26) to release the V-belts.
5. Place the V-belts in the desired position in the pulleys.
6. Tension the V-belts by means of the lever (26) and tighten the set screws (30). (Arrow: approx. 1 cm).
7. Close the V-belt cover and start the machine.

Maintenance

Below are the main maintenance operations, which can be divided into daily, weekly, monthly and half-yearly operations.
Failure to carry out the scheduled operations will result in premature wear and reduced machine performance.
Daily maintenance
– General cleaning of the machine from chips.
– Cleaning the spindle cone.
– Tool wear control.
– Check protective covers for function.
Weekly maintenance
– General, careful cleaning of the machine from chips.
– Cleaning and lubrication of the spindle.
– Sharpening of the tools.
– Check protective covers for function and possible defects.
Monthly cleaning
– Retighten all screws.
– Check protective covers and devices for integrity.

V-belt maintenance
– The V-belt must run at the correct tension so that the power of the motor is transmitted to the tool optimally. Pull out the power cable! Open the belt cover. Loosen the tension screw and tighten or loosen the motor until the belt reaches the correct tension (approx. 10mm sag).
– To change the V-belt loosen the tension screw, replace the V-belt and tension as described above. Close the belt cover again!

EXTRAORDINARY MAINTENANCE
Extraordinary maintenance must be carried out by qualified personnel. In any case it is recommended to contact your machine dealer.
The restoration of the protective covers and safety devices is also to be regarded as extraordinary maintenance.
EXTENDED MACHINE STANDSTILL
If the drill press is not used for a long time, it is recommended:
– pull out the electrical mains plug.
– to clean the machine carefully and to preserve it sufficiently.
– if necessary, cover the machine with a tarpaulin

DISPOSAL
General provisions
The final dismantling and scrapping of the machine must take into account the nature and composition of the materials to be disposed of. This means in detail:
– Ferrous materials and cast iron, which however always consists only of metal, which is a secondary raw material, must be handed over to the ironworks authorised to carry out the melting, subject to the remuneration of the components contained.
– The electrical components, including power cables and electronic material that is considered to be assimilable to urban waste, can be handed over directly to the waste collection service.
– For used mineral, synthetic or mixed oils, water-soluble oils and greases, which are special waste, you must contact the Consortium for Used Oils for storage, transport and subsequent disposal.

Note: As the regulations and laws governing disposal are constantly changing and are therefore subject to change and new regulations, the user is advised to inform himself about the respective regulations for dismantling machine tools, which may deviate from the above-mentioned standards. In any case, the information given is to be regarded as general and purely indicative.

Exploded view

Spare parts

The appendix of the instruction manual includes the list of spare parts normally available for the machine. These can be obtained from the local supplier of the machine.
When ordering, the part number, designation and quantity must be mentioned. Furthermore, always state type, serial number and year of production of the machine. Otherwise a wrong delivery may occur.

Spare parts list

1
1A
1B
1C
1D
1E
1F
1F-1
1-S1
1-S2
2Z
2-S1
2-S2
5Z
8
9
9A
15
16
18
19
20
20A
22
22A
22C
22D
22E
22-S1
22-S2
22-S3
22-S4
22-S5
22-S6
22-S7
22-S8
26
27
29L
29S
29-S1
31
31-S1
31-S2
35Z
35-S1
40
41
42
45
47
52Z
53
59Z
62
63
64
65
66
67
68
68-S1
68-S2
68-S3
69
73
76
76A
78
79
79A
79D
79E
79F
79-S1
79-S2
79-S3
79-S4
79-S5
79-S6
79-S7
79-S8
81
81-S1
85
85-S1
86Z
89
89A
91
92
92-S1
101Z
101-S1
102P
102A
102-S1
102-S2
102-S3
103NZ
103-S1
103-S2
103-S3
104
104A
104E
108A
108D
108G
108-S1
803-S1
803
V105A
V105Z
V110| PM-930301
PM-930301-6
PM-930301-4
PM-206508
PM-930301-7
PM-919109
PM-918090
PM-930301-5
PM-930301-S2
PM-930003
PM-366004
PM-374032
PM-930305
PM-930008
PM-930009
PM-930009A
PM-366015
PM-378316
PM-930318
PM-930019
PM-930020
PM-930200
PM-930622
PM-366249
PM-918092
PM-937202
PM-937201
PM-930022-S1
PM-366030
PM-366048
PM-366050
PM-374051
PM-366023
PM-930022-S7
PM-320046
PM-930626
PM-930027
PM-366029
PM-366229
PM-930029-S1
PM-366231
PM-374032
PM-930633
PM-930534
PM-930035-S1
PM-930040
PM-366041
PM-930226
PM-366045
PM-366047
PM-930652
PM-366053
PM-366059
PM-366062
PM-366063
PM-930064
9165
9457
94 44 77
PM-930068
PM-930068-S1
PM-930068-S2
PM-930068-S3
PM-930069
PM-930073
By region
By region
PM-378378
PM-930679-1
PM-366200
PM-930079D
PM-930079E
PM-930079F
PM-320004
PM-930079-S2
PM-930079-S3
PM-930079-S4
PM-930079-S5
PM-930079-S6
PM-930079-S7
PM-930079-S8
PM-930681
PM-374083
PM-33028
PM-374083
PM-930086
PM-930089
PM-930089-1
PM-834091
PM-930092A
PM-930102K
PM-930100
PM-930102K
PM-378104
PM-8831060
PM-930104-E
PM-930708-1
PM-820608
PM-930108B
PM-930079-S2
PM-320004
PM-930679
PM-930505A
PM-930505A
PM-930510| Base
Water Tank
Base Cover
Pump Motor
Adapter
Clamp
Hose (Pump)
Hose (Table)
Screw
Screw
Column Set
Bolt
Spring Washer
Table Bracket Set
Worm
Table Handle
Handle Bolt
Seale
Clamp Handle
Table
Rack
Rack Ring
Rack Ring
Head Body
Feed Shift Cover
Valve
Fixing Plate
Nozzle
Screw
Lead Bolt
Pin
Screw
Hex Nut
Screw
Lead Bolt
Bolt
Shifter Bar
Shifter
Slide Bar (L)
Slide Bar (S)
Washer
Motor Base
Spring Washer
Hex Nut
Feed Shaft Set
Hex Nut
Feed Handle
Grip
Scale Ring
Scale
Spring Cap
Spindle Set
Rubber Washer
Spindle Sleeve Set
Snap Ring
Pulley Nut
Spindle Pulley
Taper Arbor
Drill Chuck
Drill Shifter
Motor
Bolt
Washer
Hex Nut
Motor Wire
Motor Pulley
Wire
Wire Plug
Rotary Cam Switch
Switch Cover
Switch Retainer Plate
Switch Board
Bush
Switch Board
Screw
Screw
Hex Nut
Screw
Hex Nut
Screw
Hex Nut
Screw
Pulley Cover
Screw
Pulley Cover Knob
Screw
Transmitting Pulley Set
V-Belt
V-Belt
Hex Wrench
Limit Switch
Screw
Micro Switch Bracket Set
Screw
Safety Guard
Safety Guard Slide
Lead Bolt
Screw
Washer
Bracket Rod Set
C-Ring
Washer
Screw
Emergency Stop Switch
Bouchon “Marche”
Selection Switch (Pump)
Aluminum Rail Din
Magnetic Switch
Grounding
Screw
Screw
Switch Cover
Slider GIB
Vise Set
Mount Piece
---|---|---

Environmental protection
Protect the environment.
Your appliance contains valuable materials which can be recovered or recycled. Please leave it at a specialized institution.
**** This symbol indicates separate collection for electrical and electronic equipment required under the WEEE Directive (Directive 2012/19/EC) and is effective only within the European Union.

Warranty

TOOL FRANCE S.A.S guarantees that the supplied product(s) is/are free from material defects and manufacturing faults. This warranty does not cover any defects which are caused, either directly or indirectly, by incorrect use, carelessness, damage due to accidents, repairs or inadequate maintenance or cleaning as well as normal wear and tear.
Further details on warranty (e.g. warranty period) can be found in the General Terms and Conditions (GTC) that are an integral part of the contract. These GTC may be viewed on the website of your dealer or sent to you upon request.
TOOL FRANCE S.A.S reserves the right to make changes to the product and accessories at any time.

TOOL FRANCE S.A.S
9 Rue des Pyrénées, 91090 LISSES, France –
www.promac.fr

References

• Accueil Tool France Promac Tool France

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>