TOOL FRANCE TFD-32TE Drill Press User Manual

TFD-32TE
Operator’s Manual
Drill Press

TFD-32TE Drill Press

CAUTION: Read and follow all Safety Rules and Operating Instructions before First Use of this Product. Keep this manual with tools.

CE-Conformity Declaration
Product: Drill Press
TF-32TE
Brand: TOOL FRANCE
Manufacturer:
TOOL FRANCE SAS
9 Rue des Pyrénées, 91090 LISSES, France
We hereby declare that this product complies with the regulations
2006/42/EC
Machinery Directive
2014/30/EU
electromagnetic compatibility
designed in consideration of the standards
EN ISO 12100:2010
EN 60204-1:2018
EN IEC 61000-6-2:2019, EN IEC 61000-6-4:2019, EN IEC 61000-3-2:2019,
EN 61000-3-3:2013+A1:2019
EN 12717:2001+A1:2009
Responsible for the Documentation:
Head of Product-Mgmt.
TOOL FRANCE SAS

2021-12-17 Christophe SAINT SULPICE, General Manager
TOOL FRANCE SAS
9 Rue des Pyrénées, 91090 LISSES, France

UK Declaration of Conformity

Product: DRILL PRESS
Model: TFD-32TE
Brand:
Manufacturer or authorized representative:
TOOL FRANCE S.A.S
Unit 1a Stepnell Park
Off Lawford Road
Rugby
CV21 2UX
United Kingdom
We hereby declare that this product complies with the regulations:
Supply of Machinery (Safety) Regulations 2008
Electromagnetic Compatibility Regulations 2016
designed in consideration of the standards:
BS EN ISO 12100:2010
BS EN 60204-1:2018
BS EN 12717:2001+A1:2009
BS EN IEC 61000-6-2:2019
BS EN IEC 61000-6-4:2019
Responsible for the Documentation:
**TOOL FRANCE S.A.S

2021‐12‐17 Christophe SAINT SULPICE, General Manager
TOOL FRANCE S.A.S**
9 Rue des Pyrénées, 91090 LISSES, France

Technical Specification

Attention: Please choose proper power source, voltage and frequency that are shown in the label for your drill press.

SAFETY

WARNING: To avoid electrical hazards, fire hazards, or damage to the tool, use proper circuit protection.
Use a separate electrical circuit for your tools. To avoid shock or fire, replace power cord immediately if it is worn, cut or damaged in any way.
GENERAL SAFETY INSTRUCTIONS
WARNING: To avoid mistakes that could cause serious injury, do not plug the Drill Press in until you have read and understood the following:

1. READ and become familiar with the entire instruction manual. LEARN the tool’s application, limitations and possible hazards.

2. KEEP GUARDS IN PLACE and in working order.

3. REMOVE ADJUSTING KEYS AND WRENCHES. Form a habit of checking to see that keys and adjusting wrenches are removed from the tool before turning ON.

4. KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents.

5. DON’T USE IN DANGEROUS ENVIRONMENT. Don’t use power tools in damp or wet locations, or expose them to rain.
   Keep work area well lighted.

6. KEEP CHILDREN AWAY. All visitors should be kept at a safe distance from work area.

7. MAKE WORKSHOP CHILDPROOF with padlocks.

8. DON’T FORCE THE TOOL. It will do the job better and safer at the rate for which it was designed.

9. USE THE RIGHT TOOL. Do not force tool or attachment to do a job for which it was not designed.

10. USE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will result in a drop in line voltage and in loss of power that will cause the tool to overheat.

11. WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry that may get caught in moving parts. Non-slip footwear is recommended. Wear protective hair covering to contain long hair.

12. ALWAYS WEAR EYE PROTECTION. Any Drill Press can throw foreign objects into the eyes that could cause permanent eye damage. ALWAYS wear Safety Goggles (not glasses). Everyday eyeglasses have only impactresistance  lenses. They ARE NOT safety glasses.

13. SECURE WORK. Use clamps or a vise to hold work when practical. It’s safer than using your hand and it frees both hands to operate tool.

14. DISCONNECT TOOLS before servicing; when changing accessories such as blades, bits, cutters, and the like.

15. REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure switch is in OFF position before plugging in.

16. USE RECOMMENDED ACCESSORIES. Consult the instruction manual for recommended accessories. The use of improper accessories may cause serious injury.

17. NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped or if the cutting tool is unintentionally contacted.

18. CHECK FOR DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function – check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced.

19. NEVER LEAVE TOOL RUNNING UNATTENDED. TURN POWER “OFF”. Don’t leave tool until it comes to a complete stop.

20. DON’T OVERREACH. Keep proper footing and balance at all times.

21. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories.

22. DO NOT use power tools in the presence of flammable liquids or gases.

23. DO NOT OPERATE the tool if you are under the influence of any drugs, alcohol or medication that could affect your ability to use the tool properly.

24. ALWAYS operate the Drill Press in a well-ventilated area and provide for proper dust removal. Use dust collection systems whenever possible. Dust generated from certain materials can be hazardous to your health.

SPECIFIC SAFETY INSTRUCTIONS FOR THE DRILL PRESS
WARNING: For your own safety, do not try to use your drill press or plug it in until it is completely assembled and installed according to the instructions, and until you have read and understood this instruction manual.

1. THIS DRILL PRESS is intended for use in dry conditions, indoor use only.
2. WEAR EYE PROTECTION. USE a face or dust mask along with safety goggles if drilling operation is dusty. USE ear protectors, especially during extended periods of operation.
3. DO NOT wear gloves, neckties, or loose clothing.
4. DO NOT try to drill material too small to be securely held.
5. ALWAYS keep hands out of the path of a drill bit. Avoid awkward hand positions where a sudden slip could cause your hand to move into the drill bit.
6. DO NOT install or use any drill bit that exceeds 175mm in length or extends 150mm below the chuck jaws. They can suddenly bend outward or break.
7. DO NOT USE wire wheels, router bits, shaper cutters, circle (fly) cutters, or rotary planers on this drill press.
8. WHEN cutting a large piece of material, make sure it is fully supported at the table height.
9. DO NOT perform any operation freehand. ALWAYS hold the workpiece firmly against the table so it will not rock or twist. Use clamps or a vise for unstable workpieces.
10. MAKE SURE there are no nails or foreign objects in the part of the workpiece to be drilled.
11. CLAMP THE WORKPIECE OR BRACE IT against the left side of the column to prevent rotation. If it is too short or the table is tilted, clamp it solidly to the table.
12. IF THE WORKPIECE overhangs the table such that it will fall or tip if not held, clamp it to the table or provide auxiliary support.
13. SECURE THE WORK. Use clamps or a vise to hold the work when practical. It’s safer than using your hand and it frees both hands to operate tool.
14. MAKE SURE all clamps and locks are firmly tightened before drilling.
15. SECURELY LOCK THE HEAD and table support to the column, and the table to the table support before operating the drill press.
16. NEVER turn your drill press ON before clearing the table of all objects (tools, scraps of wood, etc.).
17. BEFORE STARTING the operation, jog the motor switch to make sure the frill bit does not wobble or vibrate.
18. LET THE SPINDLE REACH FULL SPEED before starting to drill. If your drill press makes an unfamiliar noise or if it vibrates excessively, stop immediately, turn the drill press OFF and unplug. Do not restart the unit until the problem is corrected.
19. DO NOT perform layout assembly or set up work on the table while the drill press is in operation.
20. USE THE RECOMMENDED SPEED for any drill press accessory and for different workpiece material.
21. WHEN DRILLING large diameter holes, clamp the workpiece firmly to the table. Otherwise, the bit may grab and spin the workpiece at high speeds. DO NOT USE fly cutters or multiple-part hold cutters, as they can come apart or become unbalanced in use.
22. MAKE SURE the spindle has come to a complete stop before touching the workpiece.
23. TO AVOID INJURY from accidental starting, always turn the switch OFF and unplug the drill press before installing or removing any accessory or attachment or making any adjustment.

ELECTRICAL REQUIREMENTS

WARNING: To avoid electrical hazards, fire hazards, or damage to the tool, use proper circuit protection. Use a separate electrical circuit for your machine. To avoid shock or fire, if power cord is worn or cut, or damaged in any way,  have it replaced immediately.
CIRCUIT DIAGRAM

Parts list of the electrical system

Index No.| Function| Specifications| Qty.| Manufacturer| Remarks
---|---|---|---|---|---
| Power cord| HO5VV-F,4X1.0mm=| 1| | EN50525-2-11
SB1| Chuck guard interlock switch| 6A| 1| JIABENT FA7-6/2-1| EN61058-1
SB2| Belt cover interlock switch| AC400V,8A| 1| KEDU QKS8| EN60947-5-1
SB3| Main switch| AC400V, 15(8)A| 1| KEDU KJD18| EN60947-5-1
SB4| Laser switch| AC250V, 6(6)A| 1| DONGKE AN18| EN61058-1
T1| Transformer| Input AC380V, output AC230V| 1| |
T2| Transformer| Input AC230V, output DC3.5V| 1| |
M| Motor| 400V,50Hz, 1100W| 1| |
VD1| Laser| DC3.5V, 1mW, 650nm| 1| |
VD2| Laser| DC3.5V, 1mW, 650nm| 1| |
VD3| LED light with switch| DC3.5V, 3W| 1| |
SDR| Speed & depth readout| | 1| |

GROUNDING INSTRUCTIONS

WARNING: This machine must be grounded while in use to protect the operator from electrical shock.
IN THE EVENT OF A MALFUNCTION OR BREAKDOWN, grounding provides a path of least resistance for electric current and reduces the risk of electric shock. This tool is equipped with an electric cord that has an equipment-grounding conductor and a grounding plug. The plug MUST be plugged into a matching receptacle that is properly installed and grounded in accordance with ALL local codes and ordinances.
DO NOT MODIFY THE PLUG PROVIDED. If it will not fit the receptacle, have the proper receptacle installed by a qualified electrician.
IMPROPER CONNECTION of the equipment-grounding conductor can result in risk of electric shock. The conductor with green insulation (with or without yellow stripes) is the equipment-grounding conductor. If repair or replacement of the electric cord or plug is necessary, DO NOT connects the equipment- grounding conductor to a live terminal.
CHECK with a qualified electrician or service person if you do not completely understand the grounding instructions, or if you are not sure the tool is properly grounded.
WARNING: Improper connection of equipment grounding conductor can result in the risk of electrical shock. Equipment should be grounded while in use to protect operator from electrical shock.
WARNING: This machine is for indoor use only. Do not expose to rain or use in damp locations.
GUIDELINES FOR EXTENSION CORDS
USE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage, resulting in loss of power and cause overheating.
Be sure your extension cord is properly wired and in good condition. Always replace a damaged extension cord or have it repaired by a qualified person before using it. Protect your extension cords from sharp objects, excessive heat and  damp or wet areas.

ACCESSORIES AND ATTACHMENTS

RECOMMENDED ACCESSORIES
WARNING: To avoid injury:

• Use only accessories recommended for this machine.
• Follow instructions that accompany accessories. Use of improper accessories may cause hazards.
• Use only accessories designed for this machine to avoid injury from thrown broken parts or workpieces.
• Do not use any accessory unless you have completely read the instruction or operator’s manual for that accessory.

CARTON CONTENTS
UNPACKING AND CHECKING CONTENTS
Carefully unpack the machine and all its parts, and compare against the illustration following.
WARNING:

• To avoid injury from unexpected starting, do not plug the power cord into a power source receptacle during unpacking and assembly. This cord must remain unplugged whenever you are assembling or adjusting the machine.
• If any part is missing or damaged, do not plug the machine in until the missing or damaged part is replaced, and assembly is complete.
• To protect the machine from moisture, a protective coating has been applied to the machined surfaces. Remove this coating with a soft cloth moistened with kerosene.

TABLE OF LOOSE PARTS
Unpack carton; check your machine to see parts listed below:

ASSEMBLY

1. Position the base on floor. Fix the column assembly to base using hex bolts.

2. Slide the table assembly with gear rack onto the column.
   Fix the gear rack using the column collar.

3. Install table and vice adjusting handle. Fix them by tightening the screws.

4. Install head assembly
   4.1. Carefully lift the head above the column and slide it onto the column
   Make sure the head slides down over the column as far as possible.
   Align the head with the base.
   4.2. Using the hex wrench, tighten the set screws in the left or right side of head.
   

5. Install three feed handles into the hub.

6. Connect the lamp plug contact to the power source plug contact in the drill head. Use four pan head screws to install the lamp assembly to the head. Turn on the LED lamp switch to check the lamp.

7. Install the chuck
   WARNING: Before any assembly of the chuck and arbor to the drill press head, clean all mating surfaces with a non-petroleum based product; such as alcohol or lacquer thinner. Any oil or grease used in the packing of these parts must be removed; otherwise the chuck may come loose during operation.
   7.1 Push the arbor onto the spindle
   7.2 Push the chuck onto the arbor.
   7.3. Using a wood mallet, firmly tap the chuck upward into position on the spindle shaft.
   

8. Install the chuck guard assembly
   Assemble the chuck guard parts together.
   Connect cable line plug connector of chuck guard to the machine plug connector. Install the chuck guard assembly to head by two screws.

ADJUSTMENT

1. Table adjustment
   A. Height adjustment
   Loosen the table bracket locking handle then adjust table to the desired position by turning the table adjusting handle.B. Tilting adjustment:
   Loosen the hex bolt. Rotate the table to desired angle left or right. Tighten the hex bolt to secure table tilt.

2. Vise adjustment
   To use the vice, Loosen the hex bolt mentioned in the previous step, and rotate the table to make the vice upward Loose the lock handle to adjust vise position.

3. Feed Depth Adjustment
   Turn the depth scale ring to the desired depth, lock the scale ring in place with the depth knob (1).
   The drill bit will stop after traveling the distance selected on the depth scale.
   Otherwise you can read the depth from the digital depth display.

4. Speed Adjustment
   This drill press has12 speeds shown in the speed label. To change the speed:
   Open the belt cover. Loosen the screws ( 1 ) with a wrench.
   Loosen the belt tension knob ( 2 ) to adjust the belt tension. Next, change the belt locations on the pulleys.
   Tighten the belts again by rotating the belt tension knob.
   Otherwise you can read the speed from the digital speed display.

5. Quill Spring Adjustment
   The quill return spring may need adjustment if the tension causes the quill to return too rapidly or too slowly.
   Take out the screw and carefully turn the spring cap counterclockwise, attach the screw to anther hole of the spring cap.

OPEARTIONS

1. Installing Drill Bit
   For self-tighten drill chuck
   • Rotate the chuck body B and the cap Ain opposite directions by your hands, then the chuck jaws C will be opened or closed.
   • Open the chuck jaws and insert the smooth end of drill bit in the chuck as far as it will go.
   • Close the chuck jaws to secure the drill bit

2. Positioning Workpiece
   To prevent the workpiece or back-up material from being torn from your hands while drilling, you MUST position it against the LEFT side of the column. Failure to do this could result in personal injury.

3. Positioning chuck guard
   Loosen the set knob, adjust the chuck guard upper or lower to guard the chuck and drill bit.

4. Using Vise
   For small workpiece that cannot be clamped to the table, use a drill press vise. The vise must be clamped or bolted to the table.
   Warning: The drill press vise MUST be clamped or bolted to the table to avoid injury from a spinning workpiece, or damaged vise orbit parts.

5. Correct Drilling Speeds
   Use the recommended speed for the drill bit and workpiece.
   Recommended Operating Speeds for twist drill bits (1/min)** Twist drill bit size| Material
   ---|---
   SOFTWOOD| HARDWOOD| ACRYLIC| BRASS| ALUMINUM| STEEL**
   3-5mm| 3000| 3000| 2500| 3000| 3000| 3000
   6-10mm| 3000| 1500| 2000| 1200| 2500| 1000
   11-16mm| 1500| 750| 1500| 750| 1500| 600
   17-25mm| 750| 500| NR| 400| 1000| 250

NR-Not Recommended
For other type drill bits, please get the recommended operating speed from the drill bit seller.

6. Using laser guide
   Warning:
   When using the laser guide, do not point the laser beam towards people and reflecting surfaces. Even a laser beam of lower intensity may cause eye damage. Therefore, do not look directly into the laser beam.
   If the laser pointer is stored for more than one month without use, please remove the batteries to avoid damage from possibly leaking batteries.
   The laser guide should be adjusted before using. To adjust the laser guide:
   • Mark an “X” on a piece of scrap wood.
   • Insert a small drill bit into the chuck and align its tip to the intersection of the lines of the “X”.
   • Secure the board to the table.
   • Turn on the laser switch and verify the laser lines align with the “X” on the workpiece.
   • If the laser lines do not align, loosen the set screw on each side of the head and rotate the laser light house until the lines meet in the center of the “X”. Retighten the lock knobs to secure.![TOOL FRANCE TFD 32TE Drill Press

• Set screw](https://manuals.plus/wp-content/uploads/2023/08/TOOL-FRANCE-TFD- 32TE-Drill-Press-Set-screw.png)

MAINTENANCE

MAINTAINING YOUR DRILL PRESS
WARNING: For our own safety, turn the switch OFF and remove the plug from the power source outlet before maintaining or lubricating your drill press.
Frequently blow out any dust that accumulates inside the motor with an air compressor or dust vacuum. A coat of paste wax applied to the table and column will help to keep the surface clean & help avoid rust.
To avoid shock or fire hazard, if the power cord is worn or cut on any way, have it replaced immediately.
LUBRICATION
All of the drill press ball bearings are packed with grease at the factory. They require no further lubrication.
Lower spindle to maximum depth and oil moderately once every three months.

TROUBLESHOOTING

Check the cable
Call for an electrician
2. Check the belt cover is proper closed, and the interlock switch is on
Check the chuck guard is proper closed, and the interlock switch is on
Noisy operation| 1. Incorrect belt tension
2. Dry spindle
3. Loose motor pulley| 1. Adjust tension
2. Lubricate spindle
3. Tighten set screw in pulley
Bit burns or smokes| 1. Incorrect speed
2. Chips not coming out of hole
3. Dull bit| 1. Change speed
2. Retract bit frequently to clear chips
3. Sharpen or replace bit
Excessive drill bit run out or wobble| 1. Bent bit
2. Bit not properly installed in chuck
3. Chuck not properly installed
4. Worn spindle bearings| 1. Replace bit
2. Install bit properly
3. Install chuck properly
4. Replace bearings
Drill bit binds in workpiece| 1. Workpiece pinching bit or excessive feed pressure
2. Improper belt tension| 1. Support or clamp workpiece, decrease feed pressure
2. Adjust tension
Workpiece torn loose from hand| 1. No supported or clamped properly| 1. Support or clamp workpiece properly

ASSEMBLY DIAGRAM

TFD-32TE PART LIST

Warranty

TOOL FRANCE S.A.S guarantees that the supplied product(s) is/are free from material defects and manufacturing faults.
This warranty does not cover any defects which are caused, either directly or indirectly, by incorrect use, carelessness, damage due to accidents, repairs or inadequate maintenance or cleaning as well as normal wear and tear.
Further details on warranty (e.g. warranty period) can be found in the General Terms and Conditions (GTC) that are an integral part of the contract.
These GTC may be viewed on the website of your dealer or sent to you upon request.
TOOL FRANCE S.A.S reserves the right to make changes to the product and accessories at any time.

TOOL FRANCE S.A.S
9 Rue des Pyrénées, 91090 LISSES, France
www.promac.fr

References

• Accueil Tool France Promac Tool France

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>