steinel 148600 CAM App User Guide

steinel 148600 CAM App User Guide

Installing the Steinel CAM App

The Steinel CAM App can be installed on the following operating systems:

• Apple iOS (min. iOS 9.3 – iPhone 5s)
• Android (min. Android 5.0.1 – Samsung Galaxy S4)

Steinel CAM App

Android

Apple iOS

Alternative:

• Scan the QR code in.
• Search for “Steinel CAM 2” in the Play Store (Android) or in the AppStore (Apple).
• Download Steinel CAM 2 app.

Mounting and booting the device

• Mount the device in the desired position in accordance with the operating instructions.
• Open the Status LED cover.
  • Device operating instructions of L 620 CAM SC.
  • Device operating instructions of XLED CAM 1 SC.
• Establish electrical supply:
  • The device boots up.
  • The light comes on.
  • Acoustic signal every 4 seconds.
  • Status LED flashes red.

Starting the Steinel CAM App

• Establish a connection to the WLAN network via smartphone.
• Start the Steinel CAM App.

The device and the smartphone or tablet must be connected to the same WLAN network.

Adding the Steinel CAM

• When installing a new device for the first time, click on the “+” symbol.
  The device is equipped with a very powerful WLAN network antenna. The device WLAN network range will be greater than the smartphone or tablet.

• Hold the smartphone or tablet close to the router during configuration.

Connecting the device to the network

While the device and WLAN router are connecting:

• Acoustic signal sounds every second.
• Status LED flashes green in rapid succession.

Once the smartphone or tablet is connected with the device:

• “Acoustic melody” sounds.
• Status LED slowly flashes green.

Please ensure that a WLAN repeater is not active at the time of installation. Mesh repeaters are not affected.

If the configuration process fails:

• Check and rule out each of the possible causes of error specified in the Steinel CAM App.

Restart the installation process:

• Wait until the device starts to issue acoustic signals every 4 seconds again.
• Repeat the process starting with “Adding the Steinel CAM” (Fig. 4.1).
  

Establishing network access

The name of the WLAN network router will be displayed in the “WiFi” field.

If the name of the WLAN network router is not displayed:

• Enable “share location” for the Steinel CAM App.
• Check to ensure that the smartphone or tablet is connected to the WLAN network.
• Enter the WLAN network router password in the Steinel CAM App.
  

Click on the eye symbol to make the password visible.

• Check the password.
• All hooks must be ticked!
• Click on “Continue”

If the fast tone is interrupted by a higher tone, the PW should be checked again.

Configuring the device

Once the connection has been established successfully, the user interface will be displayed.

• Play back live image.
• Assign a password for the device.
• Confirm the password.

The device password must contain at least 8 characters and include one letter and one numbe

Device ready for use

The device is ready for use.

FAQ – Your Questions – Our Answers

Do I need WIFI to use the Steinel CAM?

Yes, the STEINEL CAM must be integrated into a WIFI in the 2.4GHz network. Commercially available WIFI routers support both 5GHz and 2.4GHz in parallel. The STEINEL CAM can then also be accessed externally, e.g. from the mobile network.

Is it possible to switch on the light of the STEINEL CAM permanently?

Yes, if you move the “MODUS” (MODE) slider to the right position, the light is switched on permanently. To switch the light off again, move the slider to the middle position, sensor mode.

Can the microphone of the STEINEL CAM be switched off?

Yes, you can also switch off the microphone completely via the volume settings.

Can I download the recorded videos of the camera light to my smartphone?

Yes, the videos can be downloaded via the app. Afterwards they are available locally on the smartphone.

Is it possible to network the STEINEL CAM App with cables?

No, unfortunately, cable networking is not possible

Can the Steinel CAM be connected with a LAN cable?

No, the Steinel CAM must be integrated into the network via WIFI.

Is it possible to control several Camlights via one app?

Yes, it is possible to add several STEINEL CAM to the app without any problems.

What can I do if only one smartphone connects to the app and the other does

not?

Check the internet connection of the smartphone.

What can I do if the update of the light has failed?

If the update has failed, the STEINEL CAM will restart and reconnect to its known WIFI network after the restart. If the STEINEL CAM does not restart automatically, disconnect the light from the power supply briefly and wait a few seconds before reconnecting.

How can the SD card be replaced?

The STEINEL CAM requires a 2.4GHz network. Commercially available WIFI routers support both 5GHz and 2.4GHz in parallel.

Wie kann die SD-Karte ausgetauscht werden?

To replace the SD card, the lower cover of the light must be removed. The SD card is located underneath. By pressing gently on the card, it can be removed and replaced with another SD card. We recommend formatting the new SD card in “FAT32” format beforehand.

How to access or remove the SD card?

To avoid theft of your private data, access to the recordings on the SD card is only possible via STEINEL CAM App. If you have problems accessing your recordings, please contact our service hotline: +49 5245 448 188

How can I turn off the push notifications of the STEINEL CAM app?

The push notifications can be deactivated by moving the “ALARM” slider to the left position.

How to adjust the range of the light?

The sensitivity of the infrared motion detector can be decreased via the app

How can I connect another smartphone to the light?

Use the “Steinel CAM teilen” (share the Steinel CAM) function to open the QR code and the serial number of the camera light. Then open “Geteilte Steinel CAM hinzufügen“ (Add shared Steinel CAM) on the second smartphone and either scan the QR code directly or enter the serial number

How long is the warranty period for the STEINEL CAM?

We offer a 3-year manufacturer’s warranty on your STEINEL CAM.

Where can I change my password?

There is a “Passwort ändern” (change the password) function in the settings of the STEINEL CAM app

How can I minimize the detection angle of the STEINEL CAM?

You can reduce the overall sensitivity of the infrared motion detector via the settings in the app. You can hide the entire area of the infrared motion detector by masking the lens.

STEINEL GmbH
Dieselstraße 80-84
33442 Herzebrock-Clarholz
Tel: +49/5245/448-188
www.steinel.de

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>