HUBBARDTON FORGE 347295 Erlenmeyer Post Light Instruction Manual

HUBBARDTON FORGE 347295 Erlenmeyer Post Light

Product Information

Product Usage Instructions

CAUTION:

Failure to install this fixture properly may result in seriouspersonal injury or death and property damage. We recommend installation by a licensed electrician. This product must be installed in accordance with applicable installation code(s), by a person familiar with the construction and operation of the product and the hazards involved. Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

To Install (Figure 1)

SITE PREPARATION:

1. Run appropriate wiring to the site of the fixture, leaving enough excess wire to reach the top of the post, plus 12 inches.

2. Pour flat and level concrete base with wiring emerging at the center. Insert J bolts (A) so approximately 1 of the bolts are exposed above the concrete. Position J bolts according to the template on the last page of these instructions. Allow concrete to cure before installing fixture.
   INSTALLATION:

3. Position post (B) over J bolts (A), feeding supply wire up through the post and secure using flat washers (C), split washers (D), and hex nuts (E).

4. Place optional cover cap (sold separately) (F) over post (B) to conceal mounting hardware.

5. Connect fixture wires to supply wires using appropriate wire connectors (not provided), black to black (or smooth), white to white (or ribbed), and bare copper or green to bare copper or green.
   CAUTION: Make sure wire connectors are twisted on securely and no bare wire is exposed.

6. Place fixture (H) onto post (B), carefully tucking all wiring down into post and making sure no wires are pinched between the post and the fixture. Secure with set screw (G).

7. Follow steps on next page to install glass.

To Install Glass (Figure 2)

1. Unpack glass (J).
2. Install bulb (not included) into socket (I).
3. Remove the three thumb screws (L) and using the groove (K), position the glass (J) onto the fixture (H).
4. Tighten thumb screws (L) to secure the glass in place.

If you need further assistance or find that you are missing any parts, please contact the dealer from which you purchased this product. We hope you enjoy your fixture! Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping, or use of this fixture.

Component Parts

• A J Bolt
• B Post
• C Flat Washer (4)
• D Split Washer (4)
• E Hex Nut (4)
• F Cover Cap (optional)
• G Set Screw
• H Fixture
• I Socket
• J Glass
• K Ring
• L Thumb Screws (4)

ASSEMBLY & INSTALLATION INSTRUCTIONS

CAUTION : FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician. This product must be installed in accordance with applicable installation code(s), by a person familiar with the construction and operation of the product and the hazards involved.*
Caution : Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.
Please Note : After installation extra hardware and accessories are possible; our kits are used on multiple products.

To Install

CAUTION : BE SURE POWER IS OFF AT THE MAIN BREAKER BOX PRIOR TO INSTALLATION
NOTE : Fixture, Post and Cover Cap each sold separately

SITE PREPERATION:

1. Run appropriate wiring to the site of the fixture, leaving enough excess wire to reach the top of the post, plus 12 inches.

2. Pour flat and level concrete base with wiring emerging at the center. Insert J bolts (A) so approximately 1″ of the bolts are exposed above the concrete. Position J bolts according to the template on the last page of these instructions. Allow concrete to cure before installing fixture
   INSTALLATION:
   NOTE : Post may be cut to desired height before installation.

3. Position post (B) over J bolts (A), feeding supply wire up though the post and secure using flat washers (C), split washers (D) and hex nuts (E).

4. Place optional cover cap (sold separately) (F) over post (B) to conceal mounting hardware.

5. Connect fixture wires to supply wires using appropriate wire connectors (not provided), black to black (or smooth), white to white (or ribbed) and bare copper or green to bare copper or green.
   CAUTION : MAKE SURE WIRE CONNECTORS ARE TWISTED ON SECURELY AND NO BARE WIRE IS EXPOSED.

6. Place fixture (H) onto post (B), carefully tucking all wiring down into post and making sure no wires are pinched between the post and the fixture. Secure with set screw (G).

7. Follow steps on next page to install glass.

To Install Glass

1. Unpack glass (J).

2. Install bulb (not included) into socket (I).

3. Remove the three thumb screws (L) and using the synthetic grease supplied apply to the threads of all screws. Note: Application of grease to the threads will need to be done each time the screws are unthreaded during bulb maintenance.

4. Thread thumb screws (L) back in fixture. Thread each one only a thread or two.

5. Tilt glass (J), slip through bars on fixture (H), over bulb and up into ring (K).

6. Align groove in glass (J) with thumb screws (L) in ring (K).
   Note : It may be necessary to unthread thumb screws to allow glass to slide into ring. Thumb screws will not need to be completely removed.

7. Tighten thumb screws (L) evenly into groove of glass (J) to secure it in fixture (H). Note: Be sure not to overtighten screws as this could break glass.

8. Restore electricity at main breaker.

DIMENSION

USE THIS TEMPLATE TO POSITION J BOLTS AND WIREWAY IN CONCRETE SLAB PRIOR TO INSTALLING OUTDOOR POST MOUNTED LIGHTING FIXTURE
If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased this product. We hope you enjoy your fixture!
Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>