HUBBARDTON FORGE 186600 Wren Mini Pendant Instruction Manual

HUBBARDTON FORGE 186600 Wren Mini Pendant

Product Information

The A715 Wren Mini Pendant 186600 is a modern, hand-crafted lighting fixture manufactured by Modern American Blacksmiths in Castleton, Vermont, USA. It is made with fine craftsmanship and is available for purchase on the Hubbardton Forge website.

The product comes with various component parts:

• A Fixture
• B Fixture Coupling
• C Crossbar
• D Jam Nut
• E Threaded Nipple
• F Ground Screw
• G Canopy Ring
• H Canopy
• I Swivel
• J 3 Fixture Pipe (1)
• K 6 Fixture Pipe (1)
• L 12 Fixture Pipe (3)
• M Stem Nipple (6)
• N Socket
• O Bulb
• P Glass
• Q Inner Glass
• R Spacer
• S Retaining Ring
• T Bulb Shield
• U Retaining Ring Tool

Please note that extra hardware and accessories may be included due to the use of kits on multiple products and options.

Product Usage Instructions

CAUTION: Failure to install this fixture properly may result in serious personal injury or death and property damage. It is recommended to have the installation done by a licensed electrician. The product must be installed in accordance with applicable installation code(s) by someone familiar with the product’s construction and operation, as well as the associated hazards.
CAUTION: Do not exceed the maximum wattage noted on the fixture. Only use the recommended bulbs with the fixture.

To Install Fixture:

1. Make sure the power is off at the main breaker box before installation.
2. Unpack the fixture (A) from the carton carefully.
3. Thread the jam nut (D) and crossbar (C) onto the threaded nipple (E) with the ground screw (F) facing towards the swivel (I), but leave both parts loose.
4. Temporarily fasten the crossbar (C) to the electric box using two machine screws (not provided). If replacing a fixture, retain the existing screws for use with the new fixture.
5. Adjust the length of the threaded nipple (E) in the crossbar (C) so that the canopy ring (G) can hold the canopy (H) against the ceiling without any threads showing for a clean appearance. Once adjusted correctly, tighten the jam nut (D) against the crossbar (C) to secure the adjustment.
6. Remove the crossbar (C) from the electrical box and continue with the assembly instructions.
7. Locate the fixture pipes (J, K, L), fixture (A), and stem nipples (M). The nipples (M) can be found in the kit bag.
8. Choose the appropriate combination of fixture pipes (J, K, L) to achieve the desired overall fixture height.
9. Apply a thread locking compound to prevent the pipes from loosening during regular maintenance and cleaning of the fixture.
10. Slide the canopy ring (G) and canopy (H) over the wires and fixture pipes (J, K, L) until they rest on the fixture (A).
11. Pass the wires from the fixture (A) through the assembled swivel (I) and thread the swivel onto the final pipe. If necessary, remove a nipple (M) for shorter overall fixture heights.
12. Refer to the instructions on the next page to continue with the installation process.

For more information and support, visit the Hubbardton Forge website at www.hubbardtonforge.com.

MODERN AMERICAN BLACKSMITHS FINE, HAND CRAFTED LIGHTING CASTLETON, VERMONT USA HUBBARDTONFORGE.COM

Component Parts

• A Fixture
• B Fixture Coupling
• C Crossbar
• D Jam Nut
• E Threaded Nipple
• F Ground Screw
• G Canopy Ring
• H Canopy
• I Swivel
• J 3″ Fixture Pipe (1)
• K 6″ Fixture Pipe (1)
• L 12″ Fixture Pipe (3)
• M Stem Nipple (6)
• N Socket
• O Bulb
• P Glass
• Q Inner Glass
• R Spacer
• S Retaining Ring
• T Bulb Shield
• U Retaining Ring Tool

ASSEMBLY & INSTALLATION INSTRUCTIONS

Wren Mini Pendant 186600

CAUTION : FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician. This product must be installed in accordance with applicable installation code(s), by a person familiar with the construction and operation of the product and the hazards involved.*
Caution : Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.
Please Note : After installation extra hardware and accessories are possible due to our kits are used on multiple products and options

To Install Fixture

CAUTION : BE SURE POWER IS OFF AT THE MAIN BREAKER BOX PRIOR TO INSTALLATION

1. Carefully unpack fixture (A) from the carton.

2. Thread jam nut (D) and crossbar (C) onto threaded nipple (E) with ground screw (F) facing towards swivel (I); leave both parts loose.

3. Using two machine screws (not provided), temporarily fasten crossbar (C) to the electric box
   NOTE : A NEW ELECTRIC BOX COMES WITH SCREWS. WHEN REPLACING A FIXTURE, RETAIN THE EXISTING SCREWS FOR USE WITH THE NEW FIXTURE

4. Adjust the length of threaded nipple (E) in crossbar (C) so that canopy ring (G) will hold canopy (H) against the ceiling with no threads showing for best appearance. When the correct adjustment is established, tighten jam nut (D) against crossbar (C) to secure the adjustment.

5. Remove crossbar (C) from the electrical box and proceed with the assembly instructions.

6. Locate fixture pipes (J, K, L), fixture (A) and stem nipples (M). Nipples (M) can be found in the kit bag.

7. Provided are multiple fixture pipes in three different lengths. Choose the combination that will acheive the overall height desired. Refer to the table below to determine the pipes required to reach the desired overall height. Once you have determined the components necessary, feed the wires that exit fixture coupling (B) through the individual components and thread pipes and couplings together. Wires will slip easier through loose components than through pipes and couplings that are pre-assembled. Once wires are run, apply thread locking compound to all the connection points and assemble the pipes and nipples
   NOTE : APPLICATION OF THE THREAD LOCKING COMPOUND IS NECESSARY TO PREVENT THE PIPE FROM LOOSENING DURING REGULAR MAINTENANCE AND CLEANING OF THE FIXTURE. BE CERTAIN TO APPLY THE COMPOUND

8. Carefully slide canopy ring (G) and canopy (H) over wires and fixture pipes (J, K, L) until they rest on fixture (A).

9. Slip wires from the fixture (A) through assembled swivel (I) and thread swivel onto final pipe. It may be neccesary to remove a nipple (M) for this to work on shorter overall fixture heights.

10. Refer to instructions on next page to continue installation

11. Using two machine screws (not provided), fasten crossbar (C) to the electric box.

12. Using suitable wire connectors (not provided) connect fixture wires to supply (white/ribbed to white and black/smooth to black). Attach a pigtail lead to crossbar ground screw (F). Hold canopy (H) close, connect all ground wires (bare copper or green to bare copper or green).
    CAUTION : MAKE SURE WIRE CONNECTORS ARE TWISTED ON SECURELY, AND NO BARE WIRE IS EXPOSED.

13. Slide canopy (H) against ceiling, and secure with canopy ring (G).
    CAUTION : BE SURE NO WIRES ARE PINCHED BETWEEN CANOPY (H) AND THE CEILING.

14. Refer to instructions following to install bulb & glass.

15. Restore electricity at main breaker

To Install Single Glass with G9 Option

1. Install light bulb (O). Be careful not to touch bulb with bare hands; oil from the hands will dramatically reduce bulb life.
2. Slip glass (P) over socket (N).
3. Slip spacer (R) over socket (N) so it rests on glass (P) (Note orientation of spacer).
4. Thread bulb shield (T) onto socket (N) (be careful not to over tighten). Future bulb changes may be accomplished by snapping glass portion of barrier on and off rather than unthreading the holder.
5. Restore electricity at main breaker

To Install Double Glass with G9 Option

1. Install light bulb (O). Be careful not to touch bulb with bare hands; oil from the hands will dramatically reduce bulb life.
2. Slip glass (P), inner glass (Q) & spacer (R) (Note orientation of spacer) over socket (N).
3. Thread retaining ring (S) onto socket (N) using provided retaining ring tool (U).
4. Thread bulb shield (T) onto socket (N) (be careful not to over tighten). Future bulb changes may be accomplished by snapping glass portion of barrier on and off rather than unthreading the holder.
5. Restore electricity at main breaker

If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased this product. We hope you enjoy your fixture!
Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>