EXOST EI-9870 Mini Pixie Remote Control Vehicle Instructions

EXOST EI-9870 Mini Pixie Remote Control Vehicle

Installation Instructions

A Installing batteries in the transmitter:

1. Open the battery compartment.
2. Insert batteries, respecting the + and – polarities.
3. Replace the cover.

B Installing the vehicle battery:

1. Make sure the ON/OFF switch is set to OFF.
2. Open the battery compartment.
3. Insert batteries, respecting the + and – polarities.
4. Replace the cover.

C Starting:

1. Start the car.
2. To move the car forwards or backwards, push the throttle lever forwards or backwards or press the trigger (depending on the model).
3. To turn the vehicle left or right, press the steering lever to the left or right. Or, depending on the model, turn the steering wheel or move the 2 levers in opposite directions to turn.
4. To stop the vehicle, release the throttle lever.
5. If the car tends to drift to the left or right on its own, move the trimmer (beneath the car) to the right or left respectively to adjust the steering.
6. For best performance, always point the antenna towards the car.

TROUBLESHOOTING GUIDE

• Make sure the vehicle power is on.
• Make sure the batteries in transmitter and vehicle have sufficient charge.
• Check if the batteries in transmitter and vehicle are inserted with correct polarity.
• Check if the distance between transmitter and vehicle will not exceed more than 20m.
• Two or more vehicles of the same frequency will interference with each other. In such a case, move to another place or try after a while.

This product complies with the 2009/48/EC standard

WARNING:
CHOKING HAZARD – Small Parts. Not for Children Under 3 years.

Manufacturer:
Silverlit Toys Mfy Ltd. Rm 1102, 98 Granville Road, Kowloon, Hong Kong

WARNING ! Not suitable for children under the age of 3. Contains small parts which can be detached and swallowed. Risk of suffocation. BE CAREFUL : Packaging must be retained since it contains important information. Right is reserved to effects changes in colors and technical details. MADE IN CHINA. Hereby, Silverlit Toys Manufactory Ltd declares that the radio equipment type SK17040 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.silverlit.com/a/certificate

Waste electrical and electronic equipment (WEEE):
When this device reaches the end of its life, please remove all batteries and dispose of them separately. Take electrical devices to a collection centre for electronic equipment and household appliances. Other components can be disposed of with household waste.

The use of the product may be disrupted by electromagnetic interference. If this is the case, switch the device off and on again following the instructions in the user manual. If the functions are not reset, move to another location.

SAFETY CIRCUIT

During use, the internal power in the electric circuit can get quite high (for example during a 360 spin). In such a case safety circuit will shut down the vehicle for approximately 1 minute. During this period the car will not respond to signals from the transmitter. This is not a defect but a safety measure to protect the electronic circuits. After this period, the car will resume normal operation.

Instruction sheet and packaging must be retained since it contains important information.

Safety precautions

• Parents: please read the instructions with your children before using the product for the first time.
• Stop the vehicle with the remote control before picking it up.
• Keep hands, hair and clothing away from moving parts when the toy is operating.
• Do not use the vehicle with the radio control in the street. Avoid collisions with people, animals and furniture.
• Warning: any change or modification made to this product that is not expressly approved in the relevant section of the declaration of conformity may terminate the usage authorisation granted to the user.
• The wires are not to be inserted into socket-outlets.

Batteries required for the transmitter:

Power supply
DC 3 V / 0,5 W ; 2 x 1,5 V “AAA” / LR03 / AM4 not included

Battery warning

• Non-rechargeable batteries are not to be recharged.
• Rechargeable batteries are to be removed from the toy before being charged.
• Rechargeable batteries should be charged under adult supervision.
• Different types of batteries or new and used batteries are not to be mixed.
• Only batteries of the same or equivalent type as recommended are to be used.
• Batteries are to be inserted with correct polarity. (+ and –)
• Exhausted batteries are to be removed from the toy.
• The supply terminals are not to be short-circuited.
• Do not mix old and new batteries.
• Do not mix alkaline batteries, standard batteries (carbon-zinc) and rechargeable batteries (nickel-cadmium).

Batteries required for the car:

Power supply
DC 4,5 V / 5 W ; 3 x 1,5 V “AAA” / LR03 / AM4 not included

Care and maintenance

• Always remove the batteries from the toy if it is not used for a long time.
• Wipe the toy gently with a clean cloth.
• Keep the toy away from direct sources of heat.
• Do not immerse the toy in water, as this could damage electronic components.
• Replace batteries when they become less powerful.
• Operation temperature 5 – 35°C
• Receiver Category 3

Frequency Band Range: 2.400 – 2.483GHz Maximum Radio-Frequency Power:<10mW

FCC Statements

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

References

• Certificate – Silverlit

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>