MONSTER MLB7-1027-WW Multi Color Multi White LED Light Strip User Manual
- June 12, 2024
- Monster
Table of Contents
RGB+W
Multicolor + Multiwire LED Light Strip
with Remote Control
Operation Manual
MODEL MLB7-1027
V4.0 0623
Introduction
This Multi-color/Multi-white LED strip is easy to install, easy to use, and is ideal for adding ambient backlighting behind your TV or computer monitor for a great movie or gaming experience
Features
- USB powered from any 5V standard USB port
- Self-adhesive backing for easy application
- Color changing and flash modes with controllable brightness adjustment
- 44 RGB color and 44 warm white LED lights for multi-color and multi-white lighting
- 6.5ft (2m) length fits TV’s up to 65″ to create ambient backlighting
- Remote control works up to 26 feet away
- Plug and play
What’s Included
- 6.5ft RGBW LED Light Strip
- IR Remote Control with battery (1 x 3V battery, CR2025*)
- User Manual x1 pc
Safety Instructions
Please read and understand all instructions before using this product. If damage is caused by failure to follow the instructions, this warranty is null and void.
- Keep these instructions.
- Do not drop, puncture, or disassemble this product.
- Do not expose this product to dripping or splashing of drinks or liquids of any kind.
- Avoid long exposure to direct sunlight, which may cause damage.
- Do not expose this product to open flames.
- Do not use the product in a strong magnetic field.
- Use a clean, soft cloth to clean. Do not use any corrosive cleaners/oils to clean.
- Do not attempt to repair the device or open the unit as this will void the warranty.
Get Started
- Clean the surface you intend to stick the LED Light to
- Peel beginning of adhesive backing off and firmly stick LED
- Light onto the mounting surface (be careful to peel off only the backing and not the adhesive)
- Peel off more of the adhesive backing as you mount the
- LED Light, pressing and holding each section firmly against the surface
- Remove the tab from the battery compartment of the remote control
- Connect the USB cable to a USB wall charger or a power bank (1A adapter required – not included)
Installation Notes
- For best mounting results, place adhesive onto desired surface with ONE attempt. Reapplying multiple times will not guarantee secure mounting onto surface.
- Make sure the desired location is close enough to a power source like a TV’s USB port or a wall outlet with a 1A USB adapter (not included)
- For optimal performance, place IR receiver in a location away from the IR receiver on the TV to avoid interference from the TV remote control signal
- For backlighting a TV or monitor, follow the mounting diagram below:
Controls, at a Glance
| 1 | ON/OFF | Turn the product on and off |
|---|---|---|
| 2 | MULTI-WHITE SELECTORS | Select from cool, soft, or warm white |
| 3 | MULTI-COLOR SELECTORS | Change the color to match your mood |
| 4 | FLASH | Flash color-changing mode |
| 5 | STROBE | Strobe color-changing mode |
| 6 | FADE | Fade color-changing mode |
| 7 | SMOOTH | Smooth color-changing mode |
| 8 | RESET | Reset to default settings |
| 9 | DIMMER BUTTONS | Adjust the brightness/intensity |
IR Remote Operation
The battery for the remote control has already been installed.
Remove and discard the clear plastic pull tab before use.
- Turn on the LED Light by pushing the ON button on the remote control
- Select the desired color or the desired effect by pushing the corresponding button on the remote control
- Set the desired brightness using the buttons to increase/decrease the intensity of color
- Push the OFF button to turn off the LED Light
NOTE: For best operation, point the IR remote towards the IR Receiver at
the beginning of the light strip.
Changing the remote control battery:
- The battery compartment is located on the narrow side of the remote control, press the release tab inwards and remove the tray
- Remove the empty battery and insert a 3V battery, type CR2025*, with the positive terminal pointing upwards
- Place the battery compartment back in the remote control so it locks in place
- The listed battery type may differ slightly from what is supplied.
When replacing the battery, please verify the actual battery size in
the remote control.
Customer Service
1 Year Limited Warranty
Scan QR code for warranty information
866-246-2008
customerservice@monsterilluminessence.com
In the event this product becomes defective, please do not return this product
to your retailer.
Warning
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s warranty or authority to operate the
equipment.
Specifications
-
LED Light (USB): 5V
-
output: 2.5W
-
length: 6.5ft
-
remote control: 3V (1 x 3V battery, type CR2025*)
-
The listed battery type may differ slightly from what is supplied. When replacing the battery, please verify the actual battery size in the remote control.
Need the Quick Start Guide in another language?
scan for manuals
www.monsterilluminessence.com/manuals/
The illustrated products and specifications may differ slightly from those
supplied.
The M Monster logo is a registered trademark of Monster, Inc. or its
subsidiaries in the U.S. and other countries and are used under license. All
other brand names are trademarks of their respective owners. Neither Jem
Accessories, Inc. nor Monster, Inc. is affiliated with the respective owners
of their trademarks. Licensed and Manufactured by Jem Accessories, Inc.
Edison, NJ 08817. Made in China.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>