JVC CS-DR621 MWL Marine Speaker Instruction Manual
- June 12, 2024
- JVC
Table of Contents
JVC CS-DR621 MWL Marine Speaker
IMPORTANT SAFETY INSTRUCTIONS
Caution: Read this page carefully to ensure safe operation.
WARNING
- Before mounting or wiring etc., be sure to remove the wire from the battery ground terminal. (Not doing so can cause shorts or fires.)
- When extending the power supply wire (+ 12 V) or ground wire, make sure to use automotive-grade wires or other wires with the range of 0.5 mm2 (AWG 20) to 2 mm2 (AWG 18) to prevent wire deterioration and damage to the wire coating.
- To prevent a short circuit, never put or leave any metallic objects (such as coins or metal tools) inside the speaker.
- If the product emits smoke or an unusual odor, turn off the power supply immediately (set it to the standby mode) and stop using it.
- After this, please contact your dealer or nearest service station as soon as possible.
- This product is for 12 V power supply only.
- Do not attempt to open or modify the product, for this could cause fire hazard or malfunction.
- After taking the product out of the polyethylene bag, be sure to dispose of the polyethylene bag out of the reach of children. Otherwise, they may play with the bag, which could cause hazard of suffocation.
Do not ingest the battery, Chemical Burn Hazard.
The remote control supplied with this product contains a coin/button cell
battery.
- If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death.
- Keep new and used batteries away from children.
- If the battery compartment does not close securely, stop using the product and keep it away from children.
- If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.
CAUTION
- Installation and wiring of the product requires expert skill and experience. To ensure safety, be sure to have your dealer or specialist perform the installation and wiring.
- Do not install the product in a spot exposed to excessive heat or humidity.
- Do not install the product in unstable locations or locations subject to dust.
- Do not use gasoline, naphtha, or any type of solvent to clean the product. Clean by wiping with a soft, dry cloth.
- Connect the speaker wires to appropriate speaker connectors separately. Sharing the negative wire of the speaker or grounding speaker wires to the metal body of the boat/vehicle can cause this product to fail.
- When making a hole under a seat, inside the trunk, or somewhere else in the boat/ vehicle, check that there is nothing hazardous on the opposite side such as a gasoline tank, brake pipe; or wiring harness, and be careful not to cause scratches or other damage.
- Do not secure the ground wire to the bolts or nuts of important safety equipment such as: Steering or braking devices, airbag mechanisms (Can cause accidents.)
- Fasten the product securely so that it does not get detached due to sudden deceleration and becomes a hindrance to driving to ensure that it does not pose a danger to the passengers. (Cause of injury or accidents.)
- After installing the product, check that the following electrical equipment are working properly.
- Lights, navigation lights, brake lights, turn signal lights, windshield wipers, horn device, etc. The helmsman or driver must always stop the boat or vehicle in a safe location before performing the next action.
- Remote control operation
- Do not use the product for purposes other than on-board mounting.
- Keep the volume of sound at an optimum level. Not being able to hear sounds from outside of your car can lead to traffic accidents.
- To prevent damaging the speaker, turn off the power of amplifier before connecting it to the speaker.
Parts
Connections
WARNING
Remove the ignition key and disconnect the negative 0 terminal of the battery
to prevent short circuits.
CAUTION
Check that no unconnected wires or connectors are touching the metal parts or
car body.
Wiring
- In a computer-equipped boat/vehicle, when you remove the terminal of the battery, the memory may disappear, or a defect may occur in the electrical system of the boat/vehicle. Consult your dealer for further details.
- Do not allow the wire to directly contact the edge of the iron plate by using grommets.
- Do not turn the power on if the ground wire is not connected. Connect the ground wire to a metal part of the car chassis that acts as an electrical ground passing electricity to the battery’s negative terminal.
Connecting the speaker cords
With this product, the speaker cords are not supplied. Obtain the audio
speaker cords with the required length. To connect the speaker cords to the
speaker, terminate the wires with female spade connectors.
- 12 – 22 AWG speaker cord is recommended.
Connecting the power supply wires and link cable (RGB LED)
- Pass 2 heat shrink tubes 6 onto the link cable B 5·
- Connect the link cable B 5 to the left and right speakers.
- Put the heat shrink tube 6 over the connection area of the connector. Apply heat with a heat gun or similar to shrink the tube and protect the connector from moisture, etc. (Refer to Fig. 3) Protect the 2 connectors that are not in use with heat shrink tubes6· (Refer to Fig. 4)
- Connect the ground wire (black) and the + 12 V wire (yellow) of the controller of speaker A 1).
- Reconnect the negative terminal of the battery.
Do not use link cable A 4 for this connection.
- Do not connect the + 12 V wire and ground wire in reverse. Incorrect connections can cause failure.
When connecting the power supply (+12 VJ directly to the battery
CAUTION
Be sure to connect a 3 A fu se between the power cord ( + 1 2 V) of the
conrrol ler of speaker A 1 and the banery. fhe cord length between the battery
and the fuse must not exceed 90 mm (3·9/ 1 6″).
- Do not connect the + 12 V wire and ground wire in reverse. Incorrect connections can cause failure
When using multiple pairs of speakers
A maximum of up to 6 pairs of speakers can be connected.Connect the link
cables of the second and subsequent pairs of speakers as shown on rhe right
The figure shows an example of connecting 3 pairs of speakers. Connect the
founh and subsequent pairs speakers in the same way as rhe third pair Protec
the 2 connectors that are not In use with heat shrink tubes J.) (Refer to Fig.
4) You can control all the LED lights with one remote controller. but you
cannot control just a specific speaker.
Installation
Speaker locations
- Fig. 7 Examples of speaker locotlons
How to use the template
Controls
CAUTION
Do not leave or install the remote control In hot places such as on the
dashboard.
- Pull out the insulation sheet when using for the first time.
How to replace the battery
If the Remote Controller operates only over shorter distances or does not
operate at all, it is possible that the battery is depleted. In such
instances, replace the battery with new one.
CAUTION
- Risk of fire or explosion if the battery is replaced by an incorrect type. Use a button battery CR2025 (use only the approved battery).
- Risk of fire, explosion or the leakage of flammable liquid or gas if the battery is left in an extremely high temperature surrounding environment and/or subjected extremely low air pressure. The battery pack or batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
- Risk of fire, explosion or the leakage of flammable liquid or gas if the battery is disposed into fire or a hot oven, recharged, shorted, mechanically crushed or cut of the battery.
- If spilled fluid comes in contact with your eyes or on clothing, immediately rinse with water and consult a physician.
Troubleshooting
Often, what appears to be a malfunction is due to user error. Before calling for service, please consult the following table.
| Problem | Cause | Remedy |
|---|
__
__
__
RGB LED doesnot light .
| • The power supply of the +12 V wire is not connected.| • Connect the
wire correclty.
· The link cable is connected improperly.| • Insert the connector all the
way in.
• The remote controlbattery is exhausted.| • Replace with new battery.
• The product is in the standby mode.| • Press the Q) (Turn on/Standby)
key on the remote control to turn on the product.
__
Remote control opera – tion isnot possible .
| • The remote control battery is exhausted.| • Replace with new battery.
• The remote controller is too far away from the speaker or there is an
obstacle in between .| • Operate the remote controller unit within the
controllable range. Remote distance (open area) : 30 m (98 ft.)
Specifications
Design and specifications are subject to change without notice.
Speakers
- Woofer ………………………………………………… 16 cm (6-1/2 in.) PP Mica cone
- Tweeter ……………………………………… 1.3 cm (1 /2 in.) PEI Balanced dome
- Peak power ……………………………………………………………………………………………. 260 W
75 Watts RMS
- Impedance …………………………………………………………………………………………….. 4 0
- Sensitivity ………………………………………………………………………. 86 dB/Wat 1 m
- Frequency response ……………………………………………… 65 Hz~ 21,000 Hz
- Cutout diameter ………………………………….. 5-1 l /16 in. (14.48 cm) Circle
- Mounting depth ………………………………………………….. 2-9/16 in. (6.49 cm)
[Control unit]
- Operating voltage …………………………. 12 V DC boat battery/car battery
- Maximum current consumption ……………………………………… 0.5 A (1 pair)
- Remote distance (open area) ……………………………………………… 30 m (98 ft.)
IPXS Water resistant
- Mounting hole/ Orifice de montage/ Agujero de montaje Unit: mm (inch)/ Unite: mm (pouces) / Unidad: mm (pulgada)
FCC CAUTION
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equip- ment generates, uses and can radiate radio frequency energy and, if not installe-nications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Supplier’s Declaration of Conformity
- Trade Name: IVC
- Products: SPEAKER
- Model Name: CS-DR621MWL/ CS-DR620MBL
- Responsible Party: JVCKENWOOD USA CORPORATION 2201 East Dominguez Street, Long Beach, CA 90810, U.S.A. PHONE: 310 639-9000
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:
- THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
- THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
CALIFORNIA, USA ONLY
This product contains a CR Coin Cell Lithium Battery which contains
Perchlorate Material special handling may apply. See
www.dtsc.ca.gov/hazardouswaste/perchlorate
TEMPLATE GABARIT PLANTILLA
LIMITED WARRANTY
ONL y FOR PRODUCT PURCHASED IN U.S.A.
JVCKENWOOD USA Corporation (JVC) warrants this product and all parts there
of, except as set forth below ONLY TO THE ORIGINAL RETAIL PURCHASER to be FREE
FROM DEFECTIVE MATERIALS AND WORKMANSHIP from the date of original purchase
for the period shown below. (“The Warranty Period”)
THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY (50) UNITED STATES, THE DISTRICT OF COLUMBIA AND IN THE COMMONWEALTH OF PUERTO RICO.
WHAT WE WILL DO:
If this product is found to be defective within the warranty period, JVC will
repair or replace defective parts with new or rebuilt equivalents at no charge
to the original owner. Such repair and replacement services shall be rendered
by JVC during normal business hours at JVC authorized service centers. Parts
used for replacement are warranted only for the remainder of the Warranty
Period. All products may be brought to a JVC authorized service center on a
carry-in basis.
WHAT YOU MUST DO FOR WARRANTY SERVICE:
Please do not return your product to the retailer Instead, return your product
to the JVC authorized service center nearest you. If shipping the product to
the service center, please be sure to package it carefully, preferably in the
original packaging, and include a brief description of the problem(s). Please
call 1-800-252-5722 to locate the
nearest JVC authorized service center. Service locations can also be obtained
from our website http://www.us.jvckenwood.com.
If you have any questions concerning your JVC Product, please contact our Customer Care Center at 800-252-5722
WHAT IS NOT COVERED:
This limited warranty provided by JVC does not cover:
- Products which have been subject to abuse, accident, alteration, modification, tampering, negligence, misuse, faulty installation, lack of reasonable care, or if repaired or serviced by anyone other than a service facility authorized by JVC to render such service, or if affixed to any attachment not provided with the products, or if the model or serial number has been altered, tampered with, defaced or removed;
- Initial installation, installation and removal from cabinets or mounting systems.
- Operational adjustments covered in the Owner’s Manual, normal maintenance, video and audio head cleaning:
- Damage that occurs in shipment, due to act of God, and cosmetic damage;
- Signal reception problems and failures due to line power surge;
- User Removal Memory Devices/Video Pick-up Tubes/CCD Image Sensors are covered for 90 days from the date of purchase;
- Accessories;
- Batteries (except that Rechargeable Batteries are covered for 90 days from the date of purchase);
- Products used for commercial purposes, including, but not limited to rental.
- Loss of data resultant from malfunction of hard drive or other data storage device; There are no express warranties except as listed above. THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY, IS LIMITED TO THE DURATION OF THE EXPRESS WARRANTY HEREIN. JVC SHALL NOT BE LIABLE FOR ANY LOSS OF USE OF THE PRODUCT, INCONVENIENCE, OR ANY OTHER DAMAGES, WHETHER DIRECT, INCIDENTAL OR CONSEQUENTIAL (INCLUDING, WITHOUT LIMITATION, DAMAGE TO TAPES, RECORDS OR DISCS) RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF THIS WARRANTY. ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE, ARE LIMITED TO THE WARRANTY PERIOD SET FORTH ABOVE Some states do not allow the exclusion of incidental or consequential damages or limitations on how long an implied warranty lasts, so these limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
JVCKENWOOD USA Corporation
PO Box 22745, 2201 E. Dominguez St, Long Beach, CA 90810-5745
REFURBISHED PRODUCTS CARRY A SEPARATE WARRANTY, THIS WARRANTY DOES NOT APPLY. FOR DETAIL OF REFURBISHED PRODUCT WARRANTY, PLEASE REFER TO THE REFURBISHED PRODUCT WARRANTY INFORMATION PACKAGED WITH EACH REFURBISHED PRODUCT.
For customer use:
Enter below the Model No. and Serial No. which is located either on the rear,
bottom or side of the cabinet. Retain this information for future reference.
- Model No.:
- Serial No.:
- Purchase date :
- Name of dealer
TO OUR VALUED CUSTOMER
THANK YOU FOR PURCHASING THIS JVC PRODUCT. WE WANT TO HELP YOU ACHIEVE A PERFECT EXPERIENCE.
- NEED HELP ON HOWTO HOOK UP?
- NEED ASSISTANCE ON HOW TO OPERATE?
- NEED TO LOCATE A JVC SERVICE CENTER?
- LIKE TO PURCHASE ACCESSORIES?
- JVC IS HERE TO HELP! TOLL FREE: 1 (800)252-5722 http://www.us.jvckenwood.com
Remember to retain your Bill of Sale for Warranty Service.
Do not attempt to service the product yourself
Caution
- To prevent electrical shock, do not open the cabinet.
- There are no user serviceable parts inside.
- Please refer to qualified service personnel for repairs.
PRODUCT REGISTRATION
We suggest that you register your product since it will enable us to contact
you directly if it is ever necessary to correct a safety related condition in
your product. You can register at
www.us.jvckenwood.com Please note that failure
to register does not diminish any of your rights during the warranty period.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>