MICROJIG DV-HL0.0K6 MATCHFIT Dovetail Track Hardware Nut User Manual
- June 12, 2024
- MICROJIG
Table of Contents
Match Fit™ Dovetail Track Hardware®
User Manual
For building jigs, sleds, fixtures, and more.
DV-HL0.0K6 MATCHFIT Dovetail Track Hardware Nut
WARNING
Always wear safety glasses and hearing protection. Follow all satefy
precautions and use best practices. Microjig assumes no liability for any
products not sold and manufactured by Microjig.
Tools & Materials
Standard vs Match Fit Dovetail Router Bits
You can use any 1/2″ x 14° dovetail bit.
However, the top edges of the groove will need to be sanded smooth after
milling.
The Match Fit™ Dovetail Router Bit is engineered to route perfectly smooth
Dovetail Tracks to reduce cleanup. Learn more at: microjig.com/dv-
bit
Recommended wood types (3/4″ or thicker): void-free plywood (e.g. Baltic birch), standard MDF, or seasoned solid wood.
Required Tools (Not included)
*Optional but highly recommended.
Dovetail Track Instructions
Step 1-Cut relief grooves (optional but recommended)
TOOLS Router [A] and 1/4″ relief bit or table saw [C] CUT DEPTH (D) 11/32″
(8.7mm)
Cutting relief grooves before the dovetail grooves puts less stress on your dovetail router bit. This helps your dovetail bit last longer and ensures your tracks are straight.
Step 2 – Cut dovetail grooves
TOOLS Router [A] with 1/2″ x 14° dovetail bit [B] CUT DEPTH (D) 3/8″ (9.5mm)
Cut along along the center of your relief grooves to make your Dovetail
tracks.
If using a regular dovetail bit make 1-2 cleanup passes to smooth the edges.
TIP: For ease of use, use a small brush to apply a thin layer of paste
wax on the dovetail groove walls.
Step 3 — Creating dovetail grids
Route Dovetail Tracks 4.00″ apart on center to provide compatibility with
common clamp track accessories.
Route all cross-grain tracks (1) first, then route the tracks along the grain
(2).
Track Hardware
Screw lengths and dimensions
SCREW LENGTH (L)
| 1.0″ | 1.0″ |
|---|---|
| 1.5″ | 1.5″ |
| 2.0″ | 2.0″ |
*Screw lengths may slightly vary.
Track Nut
More info: microjig.com/hwn
CLAMPING RANGE
3/8″ (10mm)
For hidden/permanent fixtures and stops that don’t interfere. Great for
building custom shelving. Dovetail Track Nuts work with any #10-32 screws.
Make sure there is 5/16″ of the screw thread exposed.
with included 0.75″ #10-32 panhead screw and washer.
Use your own screws as needed for custom jig designs.
| 
---|---
2.0″ Track Screw
More info: microjig.com/hw20
CLAMPING RANGE
O” to 1-3/4″ (44mm)
For high torque applications, thick stops, fences, and strong hold downs. For
maximum reach.
1.5″ Track Screw
More info: microjig.com/hw15
CLAMPING RANGE
0″ to 1-1/4″ (32mm)
For high torque applications, thick stops, fences, and strong hold downs. The
most versatile Dovetail screw length.
1.0″ Track Screw
More info: microjig.com/hw10
CLAMPING RANGE
0″ to 3/4″ (19mm)
For thin stops and hold downs in tight spaces. Works with most miter gauges to
create auxiliary fences on table saws.
Compatible with Grr-ripper® push blocks to increase cutting height. Attach to
the balance support with included shoulder washers as shown below.
3-Year Warranty Registration
Register and protect your aproducts at: microjig.com/warranty
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>