Dell P4317Q Monitor Teardown Instructions
- June 6, 2024
- Dell
Table of Contents
Disassembly Procedures:
Step
| Figure|
Remark
---|---|---
S1. remove the stand| 
| Turn off the
power, Unplug external cables from a product, remove stant from produce.
S2.Remove the Rear Cover.| 
| Use Penknife to separate the deco and rear cove
follow the arrows in sequence.
Use a Philips-head screwdriver to remove 9 screws for unlocking
Rear cover (No.1~9 screw size=M3x6; Torque=6±1kgf.cm）
S3.Remove the Cables and keyboard| 
| Use a Philips-head screwdriver to remove 17 screws
for unlocking
Main board and Power board
(No.1~15 screw size=M3x6; Torque=4±1kgf.cm
No.16~17 screw size=M6x10;
Torque=12±2kgf.cm）
| Disconnect the
pins.
Use a Philips-head screwdriver to remove3 screws for unlocking
Key board (No.1~3 screw
size=Q2x2.3; Torque=0.9±0.4kgf.cm)
S4.remove BKT| 
| Use a Philips-
head screwdriver to remove8 screws for remove BKT
(No.1~8 screw size=M3x6;
Torque=4±1kgf.cm)
S5.Remove thMain and PowBoard| 
| Use a Philips-head screwdriver to remove 11 screws for
Remove
Mainboard and Inverter board
(No.1~11 screw size=M3x6;
Torque=6±1kgf.cm) Use a Philips-head screwdriver to remove6 screws for remove Power board
(No.1~6 screw size=M3x6;
Torque=6±1kgf.cm)
Use a hex screwdriver to remove 4 screws for unlocking mainboard
（No.1~4 Hex screw Torque= 4.5 ±
0.5kgf.cm)
S6.The Mainframe| 
| Mainframe
S7.Remove panel.| 
| Panel
S15.Remove capacitors| 
| Remove electrolyte
capacitors (red
mark) from printed
circuit boards
| Take out
the bulk cap. pin solder with
soldering iron and absorber
| 
| Lift the bulk
cap. Up and away from the PCB
Product material information
The following substances, preparations, or components should be disposed of or recovered separately from other WEEE in compliance with Article 4 of EU Council Directive 75/442/EEC.
| Capacitors / condensers (containing PCB/PCT) | No used |
|---|---|
| Mercury-containing components | No used |
| Batteries | No used |
| Printed circuit boards (with a surface greater than 10 square cm) | The product |
has printed circuit boards (with a surface greater than 10 square cm)
Component contains toner, ink, and liquids| No used
Plastic containing BFR| No used
Component and waste contain asbestos| No used
CRT| No used
Component contain CFC, HCFC, HFC and HC| No used
Gas discharge lamps| No used
LCD display > 100 cm2| Product has an LCD greater than 100 cm2
External electric cable| Product has external cables
Component contains refractory ceramic fibers| No used
Component contains radioactive substances| No used
Electrolyte capacitors (height > 25mm, diameter > 25mm)| Product has
electrolyte capacitors (height > 25mm, diameter > 25mm)
Tools Required
List the type and size of the tools that would typically can be used to
disassemble the product to a point where components and materials requiring
selective treatment can be removed.
Tool Description:
– Phillip head Screwdriver
– Hex Screwdriver
– Penknife
– Soldering iron and absorber
P4317Q
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>