Lenco CRW-4 Clock Radio with Wake Up Light and Bluetooth User Manual

Lenco CRW-4 Clock Radio with Wake Up Light and Bluetooth User Manual

CAUTION:

Usage of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

PRECAUTIONS BEFORE USE

KEEP THESE INSTRUCTIONS IN MIND:

1. Do not cover or block any ventilation openings. When placing the device on a shelf, leave 5 cm (2”) free space around the whole device.

2. Install in accordance with the supplied user manual.

3. Keep the device away from heat sources such as radiators, heaters, stoves, candles and other heat-generating products or naked flame. The apparatus can only be used in moderate climates. Extremely cold or warm environments should be avoided. Working temperature between 0° and 35° C.

4. Avoid using the device near strong magnetic fields.

5. Electrostatic discharge can disturb normal usage of this device. If so, simply reset and restart the device following the instruction manual. During file transmission, please handle with care and operate in a static-free environment.

6. Warning! Never insert an object into the product through the vents or openings. High voltage flows through the product and inserting an object can cause electric shock and/or short circuit internal parts. For the same reason, do not spill water or liquid on the product.

7. Do not use in wet or moist areas such as bathrooms, steamy kitchens or near swimming pools.

8. The apparatus shall not be exposed to dripping or splashing and make sure that no objects filled with liquids, such as vases, are placed on or near the apparatus.

9. Do not use this device when condensation may occur. When the unit is used in a warm wet room with damp, water droplets or condensation may occur inside the unit and the unit could maybe not work properly; let the unit stand in power OFF for 1 or 2 hours before turning on the power: the unit should be dry before getting any power.

10. Although this device is manufactured with the utmost care and checked several times before leaving the factory, it is still possible that problems may occur, as with all electrical appliances. If you notice smoke, an excessive build-up of heat or any other unexpected phenomena, you should disconnect the plug from the main power socket immediately.

11. This device must operate on a power source as specified on the specification label. If you are not sure of the type of power supply used in your home, consult your dealer or local power company.

12. Keep away from rodents. Rodents enjoy biting on power cords.

13. To clean the device, use a soft dry cloth. Do not use solvents or petrol based fluids. To remove severe stains, you may use a damp cloth with dilute detergent.

14. The supplier is not responsible for damage or lost data caused by malfunction, misuse, modification of the device or battery replacement.

15. Do not interrupt the connection when the device is formatting or transferring files. Otherwise, data may be corrupted or lost

16. If the unit has USB playback function, the usb memory stick should be plugged into the unit directly. Don’t use an usb extension cable because it can cause interference resulting in failing of data.

17. The rating label has been marked on the bottom or back panel of the apparatus.

18. This device is not intended for use by people (including children) with physical, sensory or mental disabilities, or a lack of experience and knowledge, unless they’re under supervision or have received instructions about the correct use of the device by the person who is responsible for their safety.

19. This product is intended for non professional use only and not for commercial or industrial use.

20. Make sure the unit is adjusted to a stable position. Damage caused by using this product in an unstable position vibrations or shocks or by failure to follow any other warning or precaution contained within this user manual will not be covered by warranty.

21. Never remove the casing of this apparatus.

22. Never place this apparatus on other electrical equipment.

23. Do not allow children access to plastic bags.

24. Only use attachments/accessories specified by the manufacturer.

25. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as the power supply cord or the plug, when liquid has been spilled or objects have fallen into the apparatus, when the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

26. Prolonged exposure to loud sounds from personal music players may lead to temporary or permanent hearing loss.

27. If the product is delivered with power cable or AC power adaptor :

    • If any trouble occur, disconnect the AC power card and refer servicing to qualified personnel.
    • To completely disconnect the power input, the mains plug of the apparatus shall be disconnected from the mains, as the disconnect device is the mains plug of apparatus.
    • Don’t step on or pinch the power adaptor. Be very careful, particularly near the plugs and the cable’s exit point. Do not place heavy items on the power adaptor, which may damage it. Keep the entire device out of children’s reach! When playing with the power cable, they can seriously injure themselves.
    • Unplug this device during lightning storms or when unused for a long period.
    • The socket outlet must be installed near the equipment and must be easily accessible.
    • Do not overload ac outlets or extension cords. Overloading can cause fire or electric shock.
    • Devices with class 1 construction should be connected to a main socket outlet with a protective earthed connection.
    • Devices with class 2 construction do not require a earthed connection.
    • Always hold the plug when pulling it out of the main supply socket. Do not pull the power cord. This can cause a short circuit.
    • Do not use a damaged power cord or plug or a loose outlet. Doing so may result in fire or electric shock.

28. If the product contains or is delivered with a remote control containing coin / cell batteries:
    Warning:

    • Do not ingest battery, Chemical Burn Hazard” or equivalent working.
    • [The remote control supplied with] This product contains a coin / button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death.
    • Keep new and used batteries away from children.
    • If the battery compartment does not close securely, stop using the product and keep it away from children.
    • If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.

29. Caution about the use of Batteries:

    • Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
    • Battery cannot be subjected to high or low extreme temperatures, low air pressure at high altitude during use, storage or transportation.
    • Replacement of a battery with an incorrect type that can result in an explosion or the leakage of flammable liquid or gas.
    • Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion.
    • Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or that leakage of flammable liquid or gas.
    • A battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas.
    • Attention should be drawn to the environmental aspects of battery disposal.

INSTALLATION

• Unpack all parts and remove protective material.
• Do not connect the unit to the

Those instruction are related only to products using power cable or AC power adaptor.

Warning

Do not ingest the battery, Chemical Burn Hazard. This product contains a coin/button cell battery. *If corn/button cell battery is swallowed, it can severe internal burns in just 2 hours and can lead to death. Keep new and used batteries away from children.

If the battery compartment does not close securely, stop using the product and keep it away from children

If you think batteries might have swallowed or placed inside any part of the body, seek immediate medical attention.

*The battery CR-2032 is not included

Caution

Danger of explosion if battery is incorrect replaced.
Replace only with the same or equivalent type.

Package Contents

• Clock radio with wake up light and bluetooth
• Power Adapter (VDE & UK head)
• User guide
• Remote Control
• FM antenna

Product Description

1. Microphone
2. Display
3. Light On/Select
4. Alarm 1 indicate LED
5. Alarm 1 Setting Button
6. Alarm 2 indicate LED
7. Alarm 2 Setting Button
8. Time Setting/Snooze Function/Sleep/Nap Modes
9. Play/Pause, FM Scan, Hands-free
10. Press Volume – / Hold for Previous song &Radio station
11. Press Volume + / Hold for next song &Radio station
12. Function modes indicate LED
13. Hold for the power ON/OFF,press for play modes

Controls And Indicator

1. Function Modes LED Indicator (on the front panel of the unit)
   Bluetooth mode
   Search Status : Blue LED flash quickly
   Play Status : Blue LED Stays on
   FM Radio mode
   Radio Scan : Red LED flash
   Play Status : Red LED stays on
   Line in mode
   Red LED light stays on

2. Alarm LED Indicator
   Alarm ON : Blue LED light stays on
   Alarm Off : Blue LED light Off

1. Back up battery compartment
2. Adapter DC 5V Input Jack
3. AUX IN Jack or FM Antenna
4. Stand
5. Screw for fix stand

BEFORE YOU BEGIN

The unit uses a backup battery system Button Cell CR2032. The battery must be inserted
into the battery compartment to enable backup memory, in the event of power outages or if the DC cord is accidentally disconnected. The LED display will not illuminate, but the current time and alarm settings will be maintained. As soon as the power supply returns, the LED display will indicate the correct time.

POWER

Plug the AC adaptor into the DC IN port on the back of unit, plug the other end into a wall socket.

PLAY MODES

Press button as needed to select Bluetooth, FM radio or AUX mode, Press and hold the button to scan the radio station and hold and to the desired station

SETTING THE CLOCK

1. Hold “ ”button for 3 seconds, The hour digit will begin flashing, Press  and until the correct hour is displayed.

2. Press “ ” button again to set the minutes ,The minutes digits will begin
   flashing, Press  and  until the correct minutes is displayed.

3. Press it again to exit the clock setting mode .

INSTALLING/REPLACING BACK UP BATTERY

1. Make sure the DC adapter is connected to the wall ,otherwise the time may be lost during battery replacement .
2. Open the battery compartment cover located back of unit
3. Insert button cell CR2032 ,checking that the positive polarity follows the direction of the instructions inside the battery compartment.
4. Close the compartment cover.

Note :Battery must be installed in order for time & alarm memory back-up to operate, In
the event of power failure or disconnected ,the battery is not installed ,the clock and alarm will need to be reset when power is restored.

BATTERY PRECAUTIONS

1. Use only the size and type of battery specified.
2. When installing battery ,observe proper+/- polarities ,Incorrect installation of battery may cause damage to the unit.
3. If the unit is not going to be used for a long period of time, remove the battery to prevent damage due to possible battery leakage.
4. Do not dispose of the battery in a fire ,Battery may exploded or leak.

AUX Play Mode

1. Plug one end of the 3.5mm audio cable (not included) into the headphone or line out jack of your audio device.
2. Plug the other end of the cable into the AUX jack located on the back of unit.
3. Press and hold button to turn ON the unit and press button to switch to AUX IN mode, Red LED will stay on. Turn on your audio device and play music . Make sure your audio device is charged and turned to medium volume.
4. Adjust the volume of your audio device to the desired level.
5. Press the or Button on the unit to adjust the system volume.
6. Press and hold button to turn off the unit when you are finished listening. You may also turn off your audio device.
   

Bluetooth Play Mode

If you are using a Bluetooth audio device, make sure the working distance is within 7-10 meters, different environment may have effect on the working distance

1. Press and hold button to turn ON the unit, blue LED will flash quickly.
2. Turn on the Bluetooth on your audio device.
3. Searching Devices Choose “Lenco CRW-4”.No password is required.If your device does require a password,type”0000”
4. Adjust the volume on your audio device to the desired level.
5. Press the or Button on the unit to adjust the system volume.
6. Hold the or Button on the unit to adjust the Previous/Next song.
7. Press button to pause/play music.
   

Making Calls with a Bluetooth Mobile Phone

Before you make a call with the unit, you need to pair and link your Bluetooth-enabled
phone with the unit. Please refer to Pairing procedure

1. To answer a call, press the Button. Now you can use the unit as a speaker phone.
2. Speak into the MIC and press the  or Button on the unit to adjust the call volume.
3. To end the call, press the Button.
   NOTE : the microphone is located in the front of product (near LED display).

TROUBLESHOOTING

• Make sure your speaker is turned on.Make sure your speaker is connected AC power adaptor

No sound|

• Make sure the volume of your speaker is not minimum setting.
• Make sure the connected audio device is playing audio.

Sound is distorted or intermitten|

• Turn down the volume of the speaker or the connected device.
• Power off speaker unit and turn on again.

No Radio|

• Make sure FM radio mode is selected
• Change the speaker direction or position for better reception.
• Make sure antenna cable is connected .

No Alarm|

• Mark sure Alarm 1 or Alarm 2 LED indicator is on.
• When you select Bluetooth mode as alarm mode, make sure your audio device Bluetooth is connected with speaker unit before power off the speaker unit and audio player App have not shut off

Can not pair the speaker with my Bluetooth device|

• Make sure the Bluetooth mode of your device is turned on.
• Your Bluetooth device may be out of range,try moving it closer to the speaker.
• Move your Bluetooth device and the speaker always from other devices that generate electromagnetic interference, such as phones,Microwave oven, wireless network routers or other Bluetooth devices.

FM RADIO PLAY MODE

1. Turn on the unit, press  button to FM mode ,function indicate LED will be RED, LED display will show FM frequency, plug the antenna cable in Aux-in on backside.
2. Press and hold  button to scan FM radio, the product enters the automatic scanning station and searched station automatically save, press and hold button to stop scanning and enter first station playing.
3. After the end of the automatic scan, you can press and button to select the saved radio station and play it.
   NOTE : Different places may cause to different reception effect, in order to enhance the use of effect, please try to use the place without interference and also try to change the different product or antenna direction for better reception..

Alarm1 Setting

1. Press button ,alarm 1 LED indicator stay on to show alarm 1 is on .
2. hold button to enter alarm setup mode. Press it again and the hour digit will begin flashing, Press and until the desired hour is displayed.
3. Press button again, minute digits will beginning flashing, Press and until the desired minute is displayed.
4. Set wake up alarm volume, press   and , volume from 1 to 15.
5. Press button again, Press   and button to select alarm mode (Buzzer/FM/Bluetooth mode), LED display is .
6. Press alarm again to set alarm

Alarm2 Setting

1. Press button ,alarm 2 LED indicator stay on to show alarm 1 is on .

2. hold button to enter alarm setup mode. Press it again and the hour digit will begin flashing, Press and until the desired hour is displayed.

3. Press button again, Minute digits will beginning flashing, Press and until the desired minute is displayed.

4. Set wake up alarm volume, press and , volume from 1 to 15.

5. Press button again, Press   and button to select alarm mode
   (Buzzer/FM/Bluetooth mode), LED display is .

6. Press alarm again to set alarm. The Moon light will turn on 10 minutes before the alarm ring , the moon light color will change from Red- yellow- white during these 10 minutes, and keep white color on when the alarm ring
   NOTE: Alarm time setting can only operated under alarm is on. When you select Bluetooth mode as alarm mode, make sure your audio device Bluetooth is connected with speaker unit before power off the speaker unit and audio player App have not shut off ,otherwise the alarm will not work accordingly. When the alarm is ringing, press any button on the unit to turn the alarm off ,the alarm will come on again at the same time the next day If the alarm sounds for 30 minutes continuously it will automatically turn off and reset to come on again at the same time the next day

Sleep/Nap Features

The Nap feature will wake you after a nap of 10-15-20-30-60-90 minutes without the need to change your regular alarm 1 or alarm 2 settings. Press button to select 10,15,20,30,60 or 90 minutes. The unit will turn on automatically. When in bluetooth mode, make sure your bluetooth audio device is on, otherwise the alarm won’t work accordingly.

The Sleep feature will turn off the unit after 15/30/45/60/75/90 minutes without the need to change your regular alarm 1 or alarm 2 settings.

Snooze Feature

Press Snooze button on the unit while the alarm is sounding , the blue indicator on the alarm button will flash, the alarm will cease temporarily and will go on again in 9 minutes, you may use this feature until turn the alarm off.

Light setting

1. Press the light button on the unit or on the remote control to turn on the light.
2. Press light button to select light color: purple, indigo, blue, green, yellow, red, White/ light off.
3. Hold light button ,the light automatically fade slowly from 1 color to the other.
4. Long press power button switches the device off.

Dimmer Function

Press the Volume + button on the unit or the remote control to adjust the backlight intensity of LCD display before power on the unit .There are three levels: high/mid/low.

Remote Control

1. Play modes select button
2. Power ON/OFF button
3. Volume + button/Up+ button for Time Set &Alarm set
4. Previous song button/Radio station
5. Next song button/Radio station
6. Play/Pause button/Scan radio station /Hold it for disconnect with bluetooth device
7. Volume – button /Down- button for time set & alarm set
8. Time set button
9. Hands-free button
10. Sleep/nap function set button
11. Light on/off color select button
12. Alarm 2 set button
13. Alarm 1 set button
14. Snooze button

Note: If you want adjust station manually instead of auto scan ,you can press and button to adjust step by step .

SPECIFICATIONS

• FM Frequency Range: FM 87.5 —108 MHz
• Bluetooth Range: Within 10 meters in the open area Power Source: AC/DC Power adaptor 5V/1.5A DC 1 x CR2032 batteries (For back-up, not included)
• Power Output: 2 x 3W
• Power Supply adaptor Manufacture: Dongguan Dongsong Electronic Co.,Ltd
• Model number: DYS812-050150W-KUse only original AC adaptor Use only the power supply listed in the user instructions

Guarantee

Lenco offers service and warranty in accordance to European law, which means that in case of repairs (both during and after the warranty period) you should contact your local dealer. Important note: It is not possible to send products that need repairs to Lenco directly. Important note: If this unit is opened or accessed by a non-official service center in any way, the warranty expires. This device is not suitable for professional use. In case of professional use, all warranty obligations of the manufacturer will be voided.

Disclaimer

Updates to Firmware and/or hardware components are made regularly. Therefore some of the instruction, specifications and pictures in this documentation may differ slightly from your particular situation. All items described in this guide for illustration purposes only and may not apply to particular situation. No legal right or entitlements may be obtained from the description made in this manual.

Disposal of the Old Device

This symbol indicates that the relevant electrical product or battery should not be disposed of as general household waste in Europe. To ensure the correct waste treatment of the product and battery, please dispose them in accordance to any applicable local laws of requirement for disposal of electrical equipment or batteries. In so doing, you will help to conserve natural resources and improve standards of environmental protection in treatment and disposal of electrical waste (Waste Electrical and Electronic Equipment Directive).

CE Marking

Hereby, Lenco Benelux B.V., Thermiekstraat 1a, 6361 HB Nuth, The Netherlands, declares that this product is in compliance with the essential EU directive requirements. The declaration of conformity may be consulted via
techdoc@commaxxgroup.com

Service

For more information and helpdesk support, please visit www.lenco.com Lenco Benelux BV, Thermiekstraat 1a, 6361 HB, The Netherlands.

References

• Lenco.com | Officiële Lenco Webshop‎

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>