REDARC SPMB0002 Solar Panel Mounting Bracket Instruction Manual
- June 12, 2024
- REDARC
Table of Contents
REDARC Solar® Solar Panel Mounting Bracket
SPMB0002 Solar Panel Mounting Bracket
Instruction Manual
MODEL: SPMB0002
Solar Panel Mount Bracket
The SPMB0002 Solar Brackets is best suited with REDARCs fixed solar panels and
other popular solar panels to an ARB Base Rack and Rhino–Rack Steel Mesh
Platform systems.
REDARC stock three other variants of Solar Brackets to suit different solar
panels and crossbars:
SPMB0001 — suited to mount solar panels (35 mm max. thickness) with both
Rhino–Rack vortex crossbars and the Rhino–Rack heavy duty crossbars.
SPMB0003 — compatible with REDARCs fixed solar panels to Rhino–Rack
Pioneer Platform crossbar.
SPMB0004 — suited to mount solar panels (35 mm max. thickness) with
Unistrut Series Channel systems and EzyStrut Plain Channel systems.
WARNINGS AND SAFETY INFORMATION
Save these instructions — this manual contains important safety
instructions.
Do not install the mounting brackets unless you have read and understood this
manual.
Disclaimer: REDARC accepts no liability for any injury, loss or property
damage which may occur from the improper or unsafe installation or use of its
products.
SAFETY MESSAGE CONVENTIONS
Safety messages in this manual include a signal word to indicate the level of
the hazard as follows:
CAUTION Indicates a potentially hazardous situation which, if not
avoided, may result in moderate or minor injury to the operator or to
bystanders. Read the message and follow instructions precisely.
CAUTION
- Incorrect mounting can cause the panels to become detached during travel, which causes a safety risk to road users. Ensure that you follow the manual’s instructions for correct installation.
- Incorrect installation and mounting of the solar panel can effect the performance of the solar panel.
- Leave adequate clearance around the solar panels to ensure the panels do not become partially shaded when in-use, and to allow access for maintenance of the panels and connections.
- Two people are recommended to safely lift the solar panels assembly above shoulder height (e.g. when lifting onto the roof of a vehicle during installation).
- The Solar Bracket must have both bolts attached to the solar panel. Any less will result in unsecure and unsafe mounting and may damage your solar panel during travel.
- All bolts must have at minimum two threads past the end of the nut.
- Always use appropriate personal protective equipment (PPE) when operating power tools.
Required tools for installation:
- Philips Head Screwdriver
- 4 mm Allen Key
- Power Drill
- 6.5 mm Drill Bit
- 10 mm Spanner
- Wire brush/file
SOLAR BRACKET PARTS
-
Solar Panel Bracket
Supplied with 4 sets of brackets -
M6 × 12 mm S/S Philips Bolt
Supplied with 8 bolts. -
M6 S/S Nylon Nut
Supplied with 16 Nylon nuts. -
M6 × 19 mm S/S Flat Washer
Supplied with 16 flat washers. -
M6 × 12 mm S/S Flat Washer
Supplied with 8 flat washers. -
M6 × 50 mm S/S Allen Key Bolt
Supplied with 8 bolts.
DIMENSIONS
A. 162 mm / 6.4″
B. 136 mm / 5.4″
C. 92 mm / 3.6″
D. 74 mm / 2.9″
E. 42 mm / 1.65″
INSTALLATION
DETERMINE THE MOUNTING POSITION
The Solar Brackets must be bolted and fitted to the solar panel then clamped
to the crossbars. Do not install the Solar Brackets to the crossbars first.
To determine where to bolt the Solar Brackets to the solar panel, place the
solar panel in the desired location on the crossbars and mark its position.
Note: The distance between the two crossbars must be suitable to support
the weight and size of your solar panel. Incorrect positioning of crossbars
may cause damage to your solar panel during travel. 
DRILL HOLES
Remove the brackets and drill the marked holes on the solar panel, preferably
using a 6.5 mm drill bit and stopper depth of 6.5 mm.
CAUTION
The Solar Bracket must have both fasteners attached to the solar panel. Any
less will result in unsecure and unsafe mounting, which may damage your solar
panel during travel. Holes should be deburred after drilling with a wire
brush or file.
ASSEMBLE BRACKETS TO PANEL
Position and bolt Bracket A into and in-line with the drilled holes on the
solar panel, using the supplied Nylon Nuts, M6 × 12 mm Flat Washers and M6 ×
12 mm Bolts.
CAUTION
Leave adequate clearance around the Solar Panels to ensure the panels do not
become partially shaded when in-use, and to allow access for maintenance of
the panels and connections.
MOUNT TO CROSSBARS
Lift the solar panel with the attached Solar Brackets to desired position on
the crossbars.
Place Bracket B underneath the crossbar and use the Nylon Nuts, M6 × 50 mm
Bolts and the M6 × 19 mm Flat Washers to bolt Brackets A and B together with
the crossbar clamped in the middle. Apply this fitting to each Solar Bracket
to
complete the installation. 
COMPLETED INSTALLATION
Note: Regularly check the mounting brackets for loose fasteners to avoid
damage to the solar panel and the crossbars due to loose connection.
CAUTION
All bolts must have at minimum two threads past the end of the nut.
WARRANTY
LIMITED WARRANTY
For full warranty terms and conditions, visit the Warranty page of the REDARC
website.
Refer to the web address and contact details applicable to your region.
Australia, New Zealand & Europe
www.redarc.com.au/warranty
REDARC Electronics Pty Ltd
23 Brodie Road (North),
Lonsdale SA 5160
Australia
Australia +61 8 8322 4848
New Zealand +64 9 222 1024
UK & Europe +44 (0)20 3930 8109| North America
www.redarcelectronics.com/warranty
REDARC Corporation
c/o Shallow, Inc.
308 Component Dr.
Smithfield, NC 27577
USA
USA +1 704-247-5150
Canada +1 604-260-5512
Mexico +52 558-526-2898
---|---
Design and specifications are subject to change without notice. | Copyright ©
2021 REDARC Electronics Pty Ltd. All rights reserved.
REDARC® and THE POWER OF REDARC® are trademarks of REDARC Electronics Pty Ltd.
| REDARC®, THE POWER OF
REDARC®, and REDARC Solar® are trademarks of REDARC Electronics Pty Ltd.
CONTACT
Tech Support 1300 REDARC
Head Office +61 8 8322 4848
New Zealand +64 9 222 1024
UK & Europe +44 (0)20 3930 8109
redarc.com.au
USA +1 (704) 247 5150
Canada +1 (604) 260 5512
Mexico +52 558-526-2898
redarcelectronics.com
References
- REDARC : Automotive Electronics, DC Charging & Brake Control
- REDARC : Automotive Electronics, DC Charging & Brake Control
- Product Warranty Details– REDARC
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>