Grace Company SMP-04-14669 Quilt Perfect Ruler Feet Kit Instructions
- June 12, 2024
- Grace Company
Table of Contents
Compatible with entire
Q’nique 21 series
Instructions
Parts List:
Hopping Foot Collar Assembly
SMP-04-14669| TrueTrack Foot
ACC-09-15257| Precision Foot
ACC-09-15258| Rolling Foot
ACC-09-15255
Standard Hopping Foot
SMP-04-10057| Ruler 3×8 inch
ACC-05-15299| SBHCS M3 x 8 mm (x2)
HDW-03-10966| Hopping Foot Height Tool
SMP-04-12171
Tools Needed: 3 mm Allen Wrench (not included)
Collar Installation Instructions:
These instructions will go over installing the new hopping foot collar assembly. After following these instructions, or if your machine already has the new hopping collar, continue to the “Foot Installation Instructions” on the next page.
- Use a 3 mm Allen wrench to remove the screw attaching the hopping foot to the hopping foot collar on your machine.
- Remove the needle bar thumb screw and carefully pull out the needle.
- With a 3 mm Allen wrench, loosen the hopping foot collar screw so that the collar can be pulled off the machine.
- Slide the new hopping foot collar that came with this kit onto the press bar. Make sure the bottom of the collar is even with the bottom of the press bar. Hold in place with the hopping foot collar screw.
Foot Installation Instructions:
These instructions will go over how to remove the standard foot and how to
install the new attachment feet. This process is the same for each of the
three feet.
- To remove the Standard Hopping Foot, use the 3 mm Allen wrench and take out the M3 x 8 mm SBHCS.
- Select the hopping foot you want to install and use the 3 mm Allen wrench to loosely attach it to the machine with the M3 x 8 mm SBHCS.
- Move the machine off of the fabric and turn the handwheel to lower the needle to the lowest position.
- Slide the Hopping Foot Height Tool beneath the foot. Lower the foot until it rests on height tool. Tighten the M3 x 8 mm SBHCS with the 3 mm Allen wrench.
Usage Instructions:
These instructions will go over how to use each accessory foot with the
included ruler.
Ruler:
The ruler’s straight edge and markings will assist you in stitching straight
lines as well as measuring the length of your stitches.
Note: For best
results, pair with the accessory ruler base for your machine.
TrueTrack Foot:
- Put the lip side of the ruler in front of the hopping foot. Press together until the ruler clips into place. The clip will keep the ruler attached.
- Use the ruler’s edge and markings to stitch straight lines and to measure stitch length.
- The foot’s swivel system allows you to turn the ruler to measure stitches in any direction.
- To release the ruler, press down on the back of the clip behind the foot and pull the ruler away from the foot.
Precision Foot:
Use the Precision Foot’s pointers to align your stitches with the markings on
the ruler.
- Press the lip side of the ruler to the front of the hopping foot. The ruler should align with the pointers on the hopping foot at right angles.
- Hold the ruler against the foot to stitch straight lines and to measure stitch length.
The swivel system allows you to turn the ruler to measure stitches in any direction.
Rolling Foot:
Use this foot to easily glide the ruler’s edge alongside the foot.
- Press the lip side of the ruler to the front of the hopping foot.
- Hold the ruler against the foot to stitch straight lines and to measure stitch length.
The swivel system allows you to slide the ruler along the foot and measure stitches in any direction.
The Grace Company
Phone: 1-800-264-0644
www.graceframes.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>