DRAPER Led Smd Tripod Site Light Instructions

: June 9, 2024
: DRAPER

Table of Contents

DRAPER Led Smd Tripod Site Light Instructions
1 .Specification
1. Health and Safety Information
WARNING! Do not use the product if defects are present and withdraw it
WARNING! Do not stare at the operating light source.
2. Maintenance and Troubleshooting
CAUTION! Do not immerse this product in water.
4.What’s in The Box?
5. Operation Instructions
11. Disposal
Read More About This Manual & Download PDF:
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

DRAPER Led Smd Tripod Site Light Instructions

These are the original product instructions. This document is part of the product; retain it for the life of the product, passing it on to subsequent holders. Read this manual in full before attempting to assemble, operate, or maintain this product. Always use the latest version of the product manual. The latest version can be downloaded from drapertools.com/manuals

1 .Specification

Stock No.| Part No.| Supply voltage| Bulb wattage (W)| Lumens (lm)| Beam angle (°)| Colour temperature (K)
---|---|---|---|---|---|---
03187| 110V/TSL/10W| 110V at 50Hz| 10| 1,100| 100| 6,000~6,500
03188| 110V/TSL/20W| 110V at 50Hz| 20| 2,200| 100| 6,000~6,500
03192| 110V/TSL/30W| 110V at 50Hz| 30| 3,300| 100| 6,000~6,500
03193| 110V/TSL/50W| 110V at 50Hz| 50| 5,500| 100| 6,000~6,500
03206| 230V/TSL/10W| 230V at 50Hz| 10| 1,100| 100| 6,000~6,500
03207| 230V/TSL/10W| 230V at 50Hz| 20| 2,200| 100| 6,000~6,500
03208| 230V/TSL/10W| 230V at 50Hz| 30| 3,300| 100| 6,000~6,500
03210| 230V/TSL/10W| 230V at 50Hz| 50| 5,500| 100| 6,000~6,500
EU 04351| 230V/TSL/20WFOB| 230V at 50Hz| 20| 2,200| 100| 6,000~6,500
EU 04354| 230V/TSL/50WFOB| 230V at 50Hz| 50| 5,500| 100| 6,000~6,500

This light is rated IP65. It is fully protected against dust and is protected against low pressure jets of water from all directions (limited ingress permitted). This does not include the attached plug.

1. Health and Safety Information

Important: Read all Health and Safety instructions before attempting to operate, maintain or repair this product. Non-compliance with these instructions may result in injury or damage to the user or the product. Draper Tools accepts no responsibility for improper use of this device.

Inspect the product and electrical connections for signs of damage before every

WARNING! Do not use the product if defects are present and withdraw it

from service until it has been repaired. If the external power cable is damaged, it must be replaced by suitably qualified personnel or returned to Draper Tools for repair.

If required, use an extension lead appropriate for both the product and the environment in which it is
- Ensure the extension lead is fully unwound regardless of the distance from the power supply to the
- Use a Residual Current Device (RCD) in damp
Always ensure that the voltage rating on the product is appropriate for the power supply to be used and that the plug is fitted with the correct
Remove all packaging and wrapping before
Position the product
- Use only on level
- Ensure that the product is stable and unlikely to tip
- Apply weights to the tripod legs where
- To prevent tripping, clearly mark or place barriers around the base of the product where
- This is a Class I appliance and requires an earth connection to protect against electric shock from accessible conductive parts in the event of failure of the basic
Ensure that all joints and attachments are securely fastened when the product is in use or
Keep trailing cables and extension leads tidy and secured to avoid trip

Risk of electric shock|
---|---
|

Class I product, must be earthed

| Replace any cracked protective shield

DO NOT carry the light by the cable or
WARNING! This product gets hot when in use.
NEVER place objects on the lamp area or hang objects on any part of this
NEVER use the light near flammable or combustible substances or
ALWAYS disconnect the power supply and allow at least ten minutes for the product to cool before attempting any maintenance or
ALWAYS switch off the light before disconnecting the mains

WARNING! Do not stare at the operating light source.

DO NOT pull on the cable to disconnect the light from mains
This product is certified for use in ambient temperatures of -20 to +45°C.
Replace any cracked protective
- This product includes a 4mm glass shield rated

2. Maintenance and Troubleshooting

Important: Maintenance and repair, including replacement of the light source, must only be performed by qualified personnel with sufficient knowledge of the electrical circuits used in this device.

Always disconnect the power supply and allow the lamp to cool before
Clean the lamp using a dry cloth ONLY.

CAUTION! Do not immerse this product in water.

Store the product in a clean and dry environment, out of reach of children, with all joints firmly
- Use a Residual Current Device (RCD) in damp

If the light does not illuminate when switched on, check that all power connections are secured and active.

4.What’s in The Box?

Carefully remove the product from the packaging and examine it for any signs of damage that may have occurred during shipment.

5. Operation Instructions

Before use, check that all parts are present and not damaged.

11. Disposal

Do not dispose of electrical products with household waste. At the end of its working life, or when it can no longer be repaired, dispose of the site
light according to local regulations.
Draper Tools Limited, Hursley Road, Chandler’s Ford, Eastleigh, Hampshire, SO53 1YF, UK Delta International, Delta International BV, Oude Graaf 8, 6002 NL, Weert, Netherlands