Grace Company XE190 Q’nique 19X Elite Quilting Machine Instruction Manual

June 10, 2024
Grace Company

XE190 Q’nique 19X Elite Quilting Machine

Product Information

The product is a quilting machine with the model number XE190
and version 1.8. The machine is manufactured by Grace Company and
comes with a unique name of Q’nique19XEli_te. The machine has
various accessories that can be purchased separately to enhance its
functionality.

Important Safeguards

When using the quilting machine, it is important to follow basic
safety precautions to avoid electric shock, burns, fire, or injury
to persons. The machine must be grounded at all times to reduce the
risk of electric shock in case of malfunction or breakdown. The
grounding pin should be connected to an appropriate outlet that is
properly installed and grounded in accordance with all local codes
and ordinances. Always unplug the machine from the electric outlet
immediately after using and before cleaning.

Product Usage Instructions

  1. Use the My Machine Details page in the instruction manual to
    write down information about your machine, including the machine
    type, serial number, date of purchase, and the frame you are using.
    This information will be helpful if you ever need to call a Grace
    Company support technician.

  2. Find your serial number on the silver sticker on the back of
    the machine. You may also be asked about your machine’s firmware
    version, which can be found on the display after the machine is
    assembled and turned on. Refer to page 83 for details.

  3. Connect the quilting machine to a surge protector that is
    connected to a backup battery supply if using it in an area with
    inconsistent input power.

  4. The machine must be grounded at all times using the grounding
    pin and an appropriate outlet that is properly installed and
    grounded in accordance with all local codes and ordinances.

  5. Do not modify the plug provided with the product. If it will
    not fit the outlet, have a proper outlet installed by a qualified
    electrician.

  6. Always unplug the machine from the electric outlet immediately
    after using and before cleaning.

Instruction Manual

Copyright June 15, 2022

V 1.8

XE190

My Machine Details
Use this page to write down information about your machine. This will be helpful if you ever need to call a Grace Company support technician.
Machine Type: Q’n_iqu_e_1_9_XE_li_te___

Machine Serial Number: ___

Date of Purchase: ____

What Frame are You Using? ____

Select Which Machine Accessories You Have Purchased:

· QuiltMotion · Back Handles · Q’nique Laser Stylus · Magnifique Magnifying Glass · Ruler Base

· Quilt Perfect Ruler Feet Kit · 360 Wonder Foot · 4 Piece Accessory Hopping Foot · 9 Piece Accessory Hopping Foot · Thread Spool Accessory

Find your serial number on the silver sticker on the back of the machine.

You may also be asked about your machine’s
firmware version. You can find this on the display after the machine is assembled and turned on.
See page 83 for details.

.#.# #X##

XX/XX/XX

Important Safeguards
When using an electrical appliance, basic safety precautions should always be followed, including the following.
DANGER – To reduce the risk of electric shock, do not leave the machine unattended when plugged in. Always unplug this machine from the electric outlet immediately after using and before cleaning.
WARNING – To reduce the risk of burns, fire, electric shock, or injury to persons:
· This appliance is not to be used by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
· Children should be supervised to ensure that they do not play with the appliance. Children shall not play with the appliance.
· Cleaning and user maintenance shall not be made by children without supervision. · Use this machine only for its intended use as described in this manual. Use only attachments
recommended by the manufacturer as contained within this manual. · Never operate this machine if it has a damaged cord or plug, it is not working properly, or it has been
dropped, damaged, or dropped into water. Return the machine to the nearest authorized dealer or service center for examination, repair, or electrical or mechanical adjustment. · Never operate the machine with any air openings blocked. Keep ventilation openings of the quilting machine free from the accumulation of lint, dust, and loose cloth. · Never drop or insert any object into any opening. · The appliance is intended for indoor use only. Do not use outdoors. · Do not operate where aerosol (spray) products are being used or where oxygen is being administered. · Connect this appliance to a properly grounded outlet only. See grounding instructions on next page. · To disconnect, turn all controls to the off position, then remove the plug from the outlet by grasping the plug. Do not pull on cord. Always switch off or unplug the appliance when leaving it unattended. · Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord. · If the supply cord is damaged, it must by replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. · Keep fingers away from all moving parts. Special care is required around the quilting machine needle. · Always use the proper needle plate. The wrong plate can cause the needle to break. · Do not use bent or damaged needles. · Do not pull or push fabric while stitching. It may deflect the needle, causing it to break. · Switch the quilting machine off when making any adjustments in the needle area, such as threading the needle, changing the needle, or changing the presser foot, etc. · Always unplug the quilting machine from the electrical outlet when removing covers, lubricating, or when making any other user servicing adjustments mentioned in the instruction manual. · CAUTION: In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by the utility.
If using this machine in an area with inconsistent input power, it is recommended the surge protector is connected to a backup battery supply.
In the instructions for electric sets shall indicate the sewing machine for which intended and how to be installed.
SAVE THESE INSTRUCTIONS! Do not discard box or packaging.
i

Important Safeguards (continued)

GROUNDING INSTRUCTIONS
This product must be grounded. In the event of malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This product is equipped with a cord that has an equipment-grounding conductor and a grounding plug. Plug the cord from the quilting machine into a surge protector. The surge protector must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

DANGER – Improper connection of the equipment-grounding conductor can result in a risk of electric shock. The conductor with insulation having an outer surface that is green, with or without yellow stripes, is the equipment- grounding conductor. If repair or replacement of the cord or plug is necessary,
do not connect the equipment-grounding conductor to a live terminal. Check with a qualified electrician or serviceman if the grounding instructions are not completely understood, or if in doubt as to whether the product is properly grounded.

Do not modify the plug provided with the product – if it will not fit the outlet, have a proper outlet installed by a qualified electrician.

To Sewing Machine

Surge Protector

Grounding Methods

Metal Screw

Grounding Pin
(A)

Cover of Grounded Outlet Box (B)

Adapter

Surge Protector

To Sewing Machine

Grounding Means
(C)

Grounding Pin
(D)

Grounding Conductor

This product is for use on a nominal 120 V circuit, and has a grounding pin as illustrated above (A). A temporary adapter, shown in (B) and (C), may be used to connect this plug to a 2-pole receptacle (B) if a properly grounded outlet is not available. The temporary adapter should be used only until a properly
grounded outlet can be installed by a qualified electrician. The green colored rigid ear, lug, and the like, extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box cover. Whenever the adapter is used, it must be held in place by the metal screw.

A qualified electrician should be consulted if there is any doubt as to whether an outlet box is properly grounded.

ii

Welcome to Your Q’nique 19X Elite

We are pleased to introduce you to the newest part of your quilting setup. This machine has been especially designed to help quilters like you have the tools available to create quality projects.

This manual is broken into four sections (or parts). Notifications at the end of each section will direct you to switch to your frame manual or QuiltMotion manual for instructions on assembling
those products. This creates a streamlined process of building a complete quilting setup in the most
efficient way. Use the following flowchart to guide you in navigating multiple manuals. If you are not using one of the products in the flowchart, just move to the next item in the chart.

Thank you again for choosing us to help with your quilting projects.

– The Grace Company

Start Here: Frame Manual: Part One
· Assemble the frame’s legs, table, and sides. · Install the channel lock onto the bottom
carriage. · Align your tracks.
Quilting Machine Manual: Part One
· Install the lower encoder onto the bottom carriage.

QuiltMotion Manual: Part One
· Prepare the bottom carriage. · Install the long belt across the frame.

Quilting Machine Manual: Part Two
· Install your machine’s wheels. · Align your wheels.
QuiltMotion Manual: Part Two
· Install the short belt. · Tension the short belt.
iv

Frame Manual: Part Two
· Install the channel lock on the machine or top plate.
· Prepare the top plate and home sewing machine.
· Place the machine or top plate on the frame.
Quilting Machine Manual: Part Three
· Install the wheel covers, display, handles, thread mast.
· Install the upper encoder.
Frame Manual: Part Three
· Install the rails and fabric bungees. · Position and adjust the rails. · Adjust the carriage stop. · Level the frame.
QuiltMotion Manual: Part Three
· Install the tablet bracket. · Plug in QuiltMotion.
Frame Manual: Part Four
· Install the velcro tape · Install the cloth leaders · Attach the fabric
Quilting Machine Manual: Part Four
· Use the quilting modes and settings in the display.
· Maintain the machine and perform repairs.
v

Table of Contents
Important Safeguards ………………………….i Welcome to Your Q’nique 19X Elite… iv
Machine Specifications………………………. vii Machine Layout………………………………. viii Ports and Plug-Ins………………………………x Included Parts & Tools ……………………… xii Animated Instructions ………………………. xv
Out-of-the Box Assembly …………….xv
Part One ……………………………..1
Task 1 – Installing the Lower Encoder ……. 2
Part Two ……………………………..7
Task 2 – Installing the Wheels ……………… 8
Part Three………………………….13
Task 3 – Installing the Wheel Covers …….. 14 Task 4 – Assembling the Handlebars ……..16 Task 5 – Connecting the Display …………..19 Task 6 – Attaching the Thread Stand……..21 Task 7 – Installing the Upper Encoder ……22 Task 8 – Turning the Machine On/Off …….24
Preparing to Quilt ……………………….25 Help Guides…………………………………….26 Task 9 – Winding a Bobbin ………………….27 Task 10 – Loading the Bobbin Case ……….30 Task 11 – Threading the Machine ………….33
Part Four……………………………38
Quilting ……………………………………..39 Choosing Machine Settings …………………40 Using the Handlebar Controls………………42 Using the Precise Quilting Mode …………..43 Using the Cruise Quilting Mode ……………45 Using Manual Quilting Mode………………..47 Using Baste Quilting Mode ………………….49 Using the Bobbin Estimator Tool…………..51 Using the Edge Warning …………………….53 Adjusting Thread Tension …………………..56 Taking Measurements ……………………….59 Making Calculations…………………………..61 Tracking Stitch Count & Run Time ………..62

Getting Started………………………………..63
Maintaining the Machine ……………..67 Preparing the Oil Bottle ……………………..68 Oiling and Cleaning …………………………..69 Changing the Needle …………………………72 Adjusting the Hopping Foot…………………74 Reinstalling the Needle Plate ……………….79 Re-assembling the Thread Tensioner …….81
Repairs and Diagnostics ………………82 Checking the Firmware ………………………83 Troubleshooting Bobbin Wind………………84 Replacing the Encoder Spring………………86 Reinstalling the Hook Holder ……………….89 Timing the Machine…………………………..92
Appendix ……………………………………96 Choosing Your Needle ……………………….97 Choosing Your Thread ……………………….99 Choosing Your Fabric and Batting ………. 102 Troubleshooting Guide…………………….. 103 Index………………………………………….. 105

vi

Machine Specifications
2

Patent: WO 2013/070633 Al Additional Patents Pending
3
4

1

Product Dimensions
Body: · Height: 680.2 mm, or 26.8 inches · Width: 395.4 mm, or 15.6 inches · Length: 831.9 mm, or 32.8 inches · Weight: 19.7 kg, or 43.5 lbs
Quilting Arm: · Height: 224.8 mm, or 8.9 inches · Length: 482.6 mm, or 19 inches
Electrical
· Input Voltage: 110-220 VAC · Peak Power Consumption: 450 W

5
Features
·1 Adjustable handles for comfortable extended use (page 16)
·2 7″ Touch Display (page 19) ·3 Dual thread mast and stands for quilting
and winding bobbin at the same time ·4 Built-in bobbin winder (page 27) ·5 Dual wheels for stability (page 8) · Stitches per minute (SPM) range of 90 to
2600 stitches · Regulated stitching · Quilt-edge warning feature
vii

Machine Layout
Quilting Machine (Side View)
7

8

6

9 12

10

11

13
18 16

14 15 16
17

4 3
5

2 1

19 20

1. Hand Wheel Raises and lowers the needle bar.
22. Bobbin Thread Tensioner (page 27) Tensions thread when winding a bobbin.
33. Bobbin Thread Cutter (page 27) Cuts wound bobbin thread.
44. Bobbin Stand (page 27) Holds the bobbin for winding.
55. Bobbin Winder Buttons (page 27) Start and stop bobbin winding.
61. Bobbin Wind Thread Stand (page 27) Holds a cone of thread for winding bobbin.
viii

72. Thread Mast (page 21) Guides thread when quilting.
81. Top Thread Stand (page 33) Holds a thread cone for threading machine.
92. Thread Guide Rod (page 33) Positions thread when quilting.
·10 Small Thread Tensioner (page 33) Tensions thread when quilting.
·11 Take-Up Lever (page 33) Tensions thread when quilting.
132. 7″ Touch Display (page 19) Provides access to quilting options.

Machine Layout (continued)

143. Handlebar Controls (page 16) Controls machine functions.
·14 Tensioner Check Spring (page 33) Applies additional tension to thread.
·15 Large Thread Tensioner (page 56) Tensions thread as adjusted when quilting.
·16 Thread Guides (page 33) Positions thread when quilting.
Hook Assembly (Front View)
21

51.7 Handle Bar Clamp (page 16) Used to adjust handlebar position.
618. Handle Bar Levers (page 16) Used to adjust handle position.
719. Lamp (page 40) Lights up needle area when machine is on.
·20 Machine Wheels (page 8) Shuttles the machine up and down the bottom carriage.

22
23 24

25

26

27

28

·21 Thread Cutter (page 30) Cuts excess thread from threading machine.
2·2 Needle Bar (page 72) Holds the needle when quilting.
·23 Hopping Foot (page 74) Presses fabric down when quilting.
·24 Needle Plate (page 79) Covers top of hook assembly.

2·5 Timing Cut-Out (page 74) Accesses hook assembly set screws.
2·6 Hook Assembly (page 30) Holds the bobbin case and hooks the top thread to create stitches.
2·7 Bobbin Case (page 27) Holds M-class bobbin and controls bottom thread tension.
2·8 Hook Assembly Cover (page 30) Covers the hook assembly area. ix

Ports and Plug-Ins
Machine Rear (Underside View) 1
2 3 4 6 5

1 Power On/Off Switch (page 24) Turns machine on and off.
2 Lower Encoder Port (page 23) Connects encoders to machine.
3 Upper Encoder Port (page 23) Connects encoders to machine.
4 Quilt Motion Tablet Port For optional automation accessory.
x

7 8
5 USB Connector Port For updating only.
6 Power Port with Retainer (page 24) Connects and holds power cable to the machine.
7 Accessory Ports For laser accessory.
8 Back Handle Ports For back handle accessory.

Machine Front

Ports and Plugins (continued)

9 Display Cable Port (page 19) Connects display cable to machine.
9

Machine Throat 10

10 Accessory Ports For laser accessory.
11 Handlebar Ports (page 16) Connects handlebar controls to machine.
11

xi

Included Parts & Tools

Level One (Workstation)

Back Wheel Base Assembly

Front Wheel Base Assembly

Tip: Parts are grouped together in the packaging for your convenience. For the best experience, do not remove parts from the packaging until instructed to do so.

SMP-09-14385 See page 8
Tools Box
T-handle Allen Wrench 4 mm
4 mm

SMP-09-14386 See page 8

T-handle Allen Wrench 3 mm
3 mm

T-handle Allen Wrench 2.5 mm
2.5 mm

T-handle Allen Wrench 2 mm
2 mm

HDW-03-13114
Flat-head Screwdriver

HDW-03-13115 Timing Spacer

HDW-03-13116 M Class Bobbin

HDW-03-13117 Needle Magnet

SMP-03-10169 See page 79
Lint Brush

SMP-03-11320 See page 92
Hopping Foot Height Tool

SMP-08-10070 See page 27
Needle Size 18 (one 10-pack) (one pre-installed)

SMP-09-13837 See page 72
Needle Size 16 (one 10-pack)

SMP-03-10170 See page 69

SMP-03-12171 See page 74

ACC-01-14517 See page 72

ACC-01-14516 See page 72
xii

Included Parts and Tools (continued)

Encoder Box
Upper Encoder (silver spring)

Lower Encoder (black spring)

Zip Tie Mount (x2)

Upper Encoder Spring (silver)

SMP-09-15701 See page 22

SMP-09-15700 See page 2

MIS-08-10805

Lower Encoder Spring (black)

Wheel Base Hardware Box

SBHCS Screw M6 x 25 mm (x2)

Shoulder Bolt M6 (x2)

HDW-03-10216 See page 86
Allen Wrench 4 mm

HDW-03-10671 See page 86

HDW-03-10215 See page 8

Wheel Base Cover Box

Front Left Wheel Base Cover

Front Right Wheel Base Cover

HDW-03-12206 See page 8
Back Left Wheel Base Cover

HDW-03-10167 See page 8
Back Right Wheel Base Cover

SMP-05-12166 See page 14
SBHCS Screw M6 x 16 mm (x4)

SMP-05-12167 See page 14

SMP-05-12164 See page 14

SMP-05-12165 See page 14

HDW-03-10974 See page 14
xiii

Included Parts and Tools (continued)

Display Box
7 Inch Touch Display SBHCS M5 x 16 mm (x2)

Thread Stand Hardware Box
SBHCS Screw M4 x 8 mm (x2)

SMP-09-15576 See page 19

HDW-03-10857 See page 19

Power Cord/Oil Bottle Box

Power Cord

Oil Bottle

HDW-03-10012 See page 21

Thumb Screw M3 (needle bar spare)

Hopping Foot Screw

SMP-02-14466 See page 24

SMP-09-13888 See page 68

HDW-03-11736 See page 72

HDW-03-10966 See page 74

Level Two
Thread Stand Assembly
SMP-09-14104 See page 21

Handlebar Assembly

Sample Thread Kit Box
Sample Thread Kit

SMP-09-14066 See page 16

MIS-11-16122

xiv

Animated Instructions
To provide the best possible customer experience, we also offer animated video instructions for setting up this product. To view the animated instructions, visit our website at: https://l.ead.me/19xelitestart. You can also use your smartphone to scan this QR code:
Out-of-the Box Assembly
This section of the manual covers all the steps to assemble the machine after you bring it home for the first time.
Task 1 – Installing the Lower Encoder ………………………………………………………..page 2 Task 2 – Installing the Wheels …………………………………………………………………..page 8 Task 3 – Installing the Wheel Covers…………………………………………………………page 14 Task 4 – Assembling the Handlebars …………………………………………………………page 16 Task 5 – Connecting the Display ……………………………………………………………….page 19 Task 6 – Attaching the Thread Stand ………………………………………………………..page 21 Task 7 – Installing the Upper Encoder ……………………………………………………….page 22 Task 8 – Turning the Machine On/Off ………………………………………………………..page 24
xv

Part One | Out of Box Assembly
Part One
Before completing the tasks in Part One of your machine instructions, please complete Part One of your frame instructions. Progress Checkpoint: Have you:
· Assembled your frame’s legs and table? · Installed and align the frame tracks? · Installed the channel lock on the bottom carriage? · Installed the rail supports? Note: Do not install the rails at this time. If you’ve already fully assembled your frame, uninstall your frame’s take-up rail.
1

Part One | Out of Box Assembly
Task 1 – Installing the Lower Encoder

Parts & Tools Needed:

Lower Encoder (black spring)

T-handle Allen Wrench 4 mm

4 mm

T-handle Allen Wrench 2.5 mm
2.5 mm

Encoder Box

Tools Box

Tools Box

Instructions
The encoders monitor the position of the machine over the frame, allowing for regulated stitching. The lower encoder is installed on the left-rear wheel of your frame’s bottom carriage. Please take the following steps to install the encoder onto the bottom carriage:

1. The parts and tools needed for this step are
located in the encoder and tools boxes. The lower encoder has the black spring and
green sticker.

Encoder Box

Tools Box

13. Locate the back left wheel of your bottom carriage. Note: If needed, review your frame assembly manual to determine the front of the bottom carriage.

21. Loosen the lock collar screw on the lower encoder with the 2.5 mm Allen wrench until the lock collar (shown in blue) turns freely.

Front

Lock Collar Screw

Note: Bottom carriage appearance will vary by model.

2

Part One | Out of Box Assembly
Installing the Lower Encoder (continued)

14. For the following steps, know whether your bottom carriage is dual-wheel (two wheels at each corner) or single-wheel (one wheel at each corner). If it is dual-wheel, does it have large wheels or small wheels?

Single-Wheel Carriage (large wheels)

Dual-Wheel Carriage (large wheels)

Dual-Wheel Carriage (small wheels)

OR

OR

15. For large wheel carriages: Use the 4 mm Allen wrench to remove the left rear wheel from the bottom carriage and install it onto the encoder screw. The wheel screw will not be needed again and can be stored with the packaging materials.

For single-wheel carriages, place the spacer on the encoder after the wheel.

Single-Wheel Carriage

Spacer

Wheel

Wheel Screw

On large dual-wheel carriages, remove the outward-facing wheel (shown in blue) and place the wheel onto the encoder screw so the wheel hub faces away from the encoder.

Large Dual-Wheel Carriage

Wheel Hub

3

Part One | Out of Box Assembly
Installing the Lower Encoder (continued)
For the small, dual-wheel bottom carriage: Do not remove the wheels. Ensure the lower encoder bracket has been installed on the back of your bottom carriage. These steps are covered in your frame instruction manual.
Small Dual-Wheel Carriage
Encoder Bracket

16. For the large wheel bottom carriages: With the 4 mm Allen wrench, screw the encoder into the left rear wheel hole on the carriage so the encoder wheel is between the rear wheels.

Single-Wheel Carriage

Encoder Wheel

Large Dual-Wheel Carriage

Encoder Wheel

For the small, dual-wheel bottom carriage: Install the encoder directly onto the encoder

bracket at the rear of the carriage so the encoder wheel is to the left of the bracket. Tighten

with the 4 mm Allen wrench. Small Dual-Wheel Carriage

Encoder Wheel

4

Part One | Out of Box Assembly
Installing the Lower Encoder (continued)

17. Turn the encoder lock collar (shown in blue) to point up. Then tighten the lock collar screw with the 2.5 mm Allen wrench.

Single-Wheel Carriage

Large Dual-Wheel Carriage

Lock Collar Screw

Lock Collar Screw

Small Dual-Wheel Carriage

18. For the large wheel bottom carriages: Take the free end of encoder cable (shown in blue) and pull it through the slot in the bottom carriage behind the wheels.

Single-Wheel Carriage

Dual-Wheel Carriage

Note: For the small dual-wheel carriage this step is not needed. 5

Part One | Out of Box Assembly
Note: Instructions for plugging the cable into the machine are covered in “Task 7” after the machine has been installed.
Congratulations! You have completed Part One of this manual. If you are also installing QuiltMotion, complete Part One of your QuiltMotion manual. If you are not installing QuiltMotion at this time, continue to Part Two of this manual on page 7.
6

Part Two | Out of Box Assembly
Part Two
Before completing the tasks in Part Two of your machine instructions, please complete Part One of your QuiltMotion instructions if you will be installing automation today. Progress Checkpoint: QuiltMotion Manual Part One (optional)
Have you: · Installed the motor plate into your bottom carriage? · Installed the long belt onto your frame?
7

Part Two | Out of Box Assembly
Task 2 – Installing the Wheels

Parts & Tools Needed:

Back Wheel Base Assembly

Front Wheel Base Assembly

SBHCS Screw M6 x 25 mm (x2)

Shoulder Bolt M6 (x2)

Packaging Level 1 (Leave in packaging)
Allen Wrench 4 mm

Packaging Level 1 (Leave in packaging)

Wheel Base Hardware Box

Wheel Base Hardware Box

Wheel Base Hardware Box
Instructions
The machine wheels move the machine across the bottom carriage. To install the machine wheels:
1. Lift up the first level of packaging and place it beside the second level. Find the Allen wrench, screws, and bolts needed for this task in wheel base hardware box.

Wheel Base Hardware Box
8

Part Two | Out of Box Assembly
Task 2 – Installing the Wheels (continued)
12. Remove the center foam from the first level of packaging. Foam
13. Take the machine body out of the second level of packaging and place it onto the wheel base assemblies in the first layer.
Back Wheel Base
Assembly
Front Wheel Base
Assembly 9

Part Two | Out of Box Assembly
Task 2 – Installing the Wheels (continued)
14. Screw the back wheel base assembly in place with two M6 x 25 mm screws SBHCS and the L-shaped 4 mm Allen wrench. SBHCS M6 x 25 mm
15. Use the L-shaped 4 mm Allen wrench to screw in the M6 shoulder bolts into the front wheel base assembly. M6 Shoulder Bolts
16. Now lift the machine out of the packaging. Place the machine onto your frame’s bottom carriage, aligning the wheels with the tracks. See your frame’s manual for bottom carriage orientation.
Note: Bottom carriage appearance may vary. 10

Part Two | Out of Box Assembly
Task 2 – Installing the Wheels (continued)
7 Loosen two wheel base set screws on one side of the machine (either the right side or left side) with the 4 mm Allen wrench.
18. Slide the machine up and down the bottom carriage tracks.

29. Check that the machine is centered over the wheels. If needed, shift the machine from side to side.

130. Re-tighten the wheel block set screws with the 4 mm Allen wrench.

11

Part Two | Out of Box Assembly
Congratulations! You have completed Part Two of this manual. If you are also installing QuiltMotion, complete Part Two of your QuiltMotion manual. If you are not installing QuiltMotion at this time but are assembling a new frame, continue to Part Two of your frame manual. If the frame manual is not broken in to parts, follow the manual’s directions to:
· Install the channel lock onto the quilting machine. If you are installing your machine onto a frame that is already fully assembled, continue to Part Three of this manual on page 13.
12

Part Three | Out-of-the-Box Assembly
Part Three
Before completing the tasks in Part Three of your machine instructions, please complete Part Two in your QuiltMotion manual (if setting up QuiltMotion at this time), and then part Two of your frame manual. Progress Checkpoint: Have you:
· Completed QuiltMotion Part Two (optional)? Have you:
· Installed the channel lock onto the quilting machine? If you’ve already fully assembled your frame: · Install the channel lock onto the quilting machine.
13

Part Three | Out-of-the-Box Assembly
Task 3 – Installing the Wheel Covers
Parts & Tools Needed:

Front Left Wheel Base Cover

Front Right Wheel Base Cover

Back Left Wheel Base Cover

Back Right Wheel Base Cover

Wheel Base Cover Box Wheel Base Cover Box Wheel Base Cover Box Wheel Base Cover Box

SBHCS Screw M6 x 16 mm (x4)

T-handle Allen Wrench 4 mm
4 mm

Wheel Base Cover Box

Instructions
Take the following steps to install the wheel base covers onto the machine:

1. The parts needed for this task are found in the wheel base cover box.

12. Locate the label on the inside of each wheel cover.

Wheel Base Cover Box
14

Part Three | Out-of-the-Box Assembly
Task 3 – Installing the Wheel Covers (continued)
23. Slide the covers onto the associated leg.

Front Left

Back Left

Back Right Front Right

34. Screw each cover into place using an M6 x 16 mm SBHCS screw and the 4 mm Allen wrench. Tighten until snug.

SBHCS M6 x 16 mm (x4)
15

Part Three | Out-of-the-Box Assembly
Task 4 – Assembling the Handlebars

Parts & Tools Needed:

Handlebar Assembly

T-handle Allen Wrench 4 mm
4 mm

Packaging Level 2

Instructions
Take the following steps to install and adjust the handlebars:

1. With the 4 mm T-handle Allen wrench, remove the handlebar clamp screw to open the handlebar clamp.

12. Take the handlebar assembly from the second level of the packaging.

Clamp Screw

Handlebar Assembly

The handlebar clamp opens.

13. Slide them into the slot so that the cables are on the bottom.

Cables 16

Part Three | Out-of-the-Box Assembly
Task 4 – Assembling the Handlebars (continued)

14. Close and hold the clamp, and loosely screw
in the clamp screw just enough to keep the clamp from opening.

27. Twist the controls vertically until they are comfortable to hold and operate.

15. Hold the handlebars at the desired angle and 18. If desired, extend the handles outward to

tighten the clamp screw.

improve the reach of the machine.

16. Open the handlebar levers (shown in blue).

19. Once you are comfortable with the position of the handles, close the handlebar levers.

17

Part Three | Out-of-the-Box Assembly
Task 4 – Assembling the Handlebars (continued)
Tip: For micro-stippling, angle the handlebars down toward the fabric in step 5, and leave the controls horizontal in step 6.
110. Plug the color-coded cables from the handlebars into the machine.
18

Part Three | Out-of-the-Box Assembly
Task 5 – Connecting the Display

Parts & Tools Needed:

7 Inch Touch Display

SBHCS M5 x 16 mm (x2)

T-handle Allen Wrench 3 mm
3 mm

T-handle Allen Wrench 2.5 mm
2.5 mm

Display Box

Display Box

Tools Box

Instructions
Take the following steps to install the display:
1. The parts needed for this step are in the display box.

Display Box

21. Use the 2.5 mm Allen wrench to remove the M4 x 6 mm SBHCS and front display cover from the machine. Front Display Cover
19

Part Three | Out-of-the-Box Assembly
Task 5 – Connecting the Display (continued)
23. Attach the 7 inch touch display with two M5 x 16 mm SBHCS and the 3 mm Allen wrench. SBHCS
M5 x 16 mm
7 Inch Touch Display
34. Re-attach the plastic cover with the 2.5 mm Allen wrench.
45. Plug the display into the port behind it, and press the cable into the cable clip to secure it.
20

Part Three | Out-of-the-Box Assembly
Task 6 – Attaching the Thread Stand

Parts & Tools Needed:

Thread Stand Assembly

SBHCS Screw M4 x 8 mm (x2)

T-handle Allen Wrench 2.5 mm
2.5 mm

Packaging Level 2

Thread Stand Hardware Box

Instructions
Take the following steps to install the thread stand assembly:

1. Take the thread stand assembly out of the second level of packaging. The screws needed for this task are in the thread stand hardware box.

Thread Stand Assembly

Thread Stand Hardware Box

23. Use the 2.5 mm Allen wrench and two
SBHCS M4 x 8 mm screws to fasten the thread stand in place.

SBHCS M4 x 8 mm (x2)

21. Slide the thread stand assembly over the screw holes on the small lip on the right side of the machine.

Thread Stand Foam

Note: If necessary, push back the foam on the thread stand to expose the screw holes.
21

Part Three | Out-of-the-Box Assembly
Task 7 – Installing the Upper Encoder

Parts & Tools Needed:

Upper Encoder (silver spring)

T-handle Allen Wrench 4 mm

4 mm

T-handle Allen Wrench 2.5 mm
2.5 mm

Encoder Box
Instructions
The encoders monitor the position of the machine over the frame, allowing for regulated stitching. The upper encoder is installed on the outer left-rear wheel of the machine. Take the following steps:

1. Use the 4 mm Allen wrench to remove the outer left rear wheel from the machine.

12. Find the upper encoder in the encoder
box. The upper encoder has a silver spring and a purple sticker on the cable.

Upper Encoder
Encoder Box

The wheel screw will not be needed again, and can be stored with the packaging materials.

13. Loosen the lock collar screw on the upper encoder with the 2.5 mm Allen wrench until the lock collar (shown in blue) turns freely.

Wheel Screw 22

Lock Collar Screw

24. Slide the wheel onto the upper encoder screw so that the wheel hub faces away from the encoder.
Wheel Hub
Encoder Screw

Part Three | Out-of-the-Box Assembly
Installing the Upper Encoder (continued)
57. Turn the encoder lock collar to the 12 o-clock position and tighten the lock collar screw with the 2.5 mm Allen wrench.

35. Place the encoder screw into the left rear wheel hole so the encoder wheel is between the two left machine wheels.

Lock Collar Screw
68. Plug the encoder cables into the encoder ports of the matching sticker color.

Encoder Wheel
46. Tighten the encoder screw with the 4 mm Allen wrench.

Encoder Screw
23

Part Three | Out-of-the-Box Assembly
Task 8 – Turning the Machine On/Off
Parts & Tools Needed:
Power Cord

Power Cord/Oil Bottle Box
Instructions
The power cable port and power switch are located on the back of the machine. To power on the machine, take the following steps:

1. Find the power cord in power cord/oil bottle box.
Power Cord/Oil Bottle Box

23. Press the power cable retainer down firmly until it grasps the power cable.

12. Lift up the power cable retainer (blue) and plug the power cord into the back of the machine.

34. Press the power switch up to turn the machine on.

Power Cord

Power Switch

24

Part Three | Preparing to Quilt
Preparing to Quilt
This section of the manual covers the steps needed to get ready to quilt. Help Guides ………………………………………………………………………………………….page 26 Task 9 – Winding a Bobbin ………………………………………………………………………page 27 Task 10 – Loading the Bobbin Case …………………………………………………………..page 30 Task 11 – Threading the Machine ……………………………………………………………..page 33
25

Part Three | Preparing to Quilt
Help Guides
For quick assistance while you’re quilting, check out the Help Guides on your machine. To reach the help guides, take the following steps: 1. Press the menu icon in the top right corner of the screen and select Help.
The Help Guide menu opens.
2 Select the item that you need help with from the menu. 26

Task 9 – Winding a Bobbin

Parts & Tools Needed:

Bobbin (Class M Large)

T-handle Allen Wrench 3 mm (optional)
3 mm

Part Three | Preparing to Quilt

Tools Box
Winding Instructions
Your machine comes with two bobbins pre-wound with 50 weight polyester Finesse thread. An empty M-class bobbin has also been provided. It’s important to choose bobbin thread that is similar in type and quality as the top thread. For more information on choosing thread, see “Choosing Your Thread” on page 99.
Note: This machine uses cone-style thread. Unless you have the spool accessory, please use only thread cones for this machine.
The following diagram outlines the path the thread (shown in blue) must take to wind the bobbin.
2 Place an empty bobbin
onto bobbin stand

4 3
11. Thread Stand 22. Guide Loops

1 6
5

33. Tensioner Thread Guide 44. Bobbin Thread Tensioner

5. Bobbin Stand with Bobbin
66. Thread Cutter 27

Part Three | Preparing to Quilt
Task 9 – Winding a Bobbin (continued)
1. Run the thread through the thread mast guide loop directly above the thread cone.
Guide Loop

14. Winding stops automatically when the bobbin is full. Cut the bobbin away from the thread cone using the thread cutter near the bobbin winder.

Thread Mast

Thread Cutter

2. Feed the thread through the back of the thread guide, then wrap it around the back of the tensioner, between the discs.

5 The bobbin thread should be neat and smooth, and not mounded to one side.

Thread Guide
3. Wrap the thread clockwise around the empty bobbin. Press start when ready.

To troubleshoot bobbin winding issues, see page 84.
Note: To stop the winding process manually, press stop.

Stop Start
28

Part Three | Preparing to Quilt
Task 9 – Winding a Bobbin (continued) Adjust Fill Levels
The bobbin winder can be adjusted to fill a bobbin to different levels if desired. 1. To adjust the bobbin winder, loosen the M5 x 16 mm SBHCS with the 3 mm Allen wrench.
SBHCS M5 x 16 mm 2 Slide the bobbin winder until the guide line underneath the bobbin is positioned where you want the bobbin thread to finish filling.
Guide Line 3 Tighten the M5 x 16 mm SBHCS to secure the bobbin winder in place.
29

Part Three | Preparing to Quilt
Task 10 – Loading the Bobbin Case

Take the following steps to insert the wound bobbin into the bobbin case and place it in the machine:

1. Check that the needle is up. If needed, rotate the hand wheel or press the “Needle Up/Down” on the display to raise the needle.

4. Pull on the bobbin case release lever (shown in blue) to remove the bobbin case from the hook assembly.

Hand Wheel

2. For your safety, press the Menu icon on the display to go to the Settings menu; this prevents the machine from stitching.

5. Place the wound bobbin into the bobbin case. Note the direction that the thread is coming off the bobbin in relation to the case.

Menu

Bobbin Case

3. Push in and down on the hook assembly cover (shown in blue) to open it.

6. Slip a few inches of thread through the slot and out of the hole.

Hole

Slot 30

Part Three | Preparing to Quilt
Task 10 – Loading the Bobbin Case (continued)
Note: If the bobbin is installed correctly, it turns clockwise when the thread is pulled.
7. Test the tension of the bobbin case every time bobbin thread is changed; bobbin tension is the foundation for correct thread tension. a. Place the bobbin case on its side, on your palm.

b. Pull up on the thread. The thread should run freely and the bobbin should rise into a vertical position without lifting off your hand.

Too Little Tension

Correct Tension

Too Much Tension

· If the bobbin case remains on its side, there is too little tension. Turn the large screw (shown below in blue) clockwise.
· If the case lifts into the air, there is too much tension. Turn the large screw (shown below in blue) counter-clockwise.
31

Part Three | Preparing to Quilt
Task 10 – Loading the Bobbin Case (continued)
8. Place the bobbin case inside the quilting machine with the release lever (shown in blue) at the 3 o’clock position. It should click into place. Do not pull on the lever while inserting the bobbin case.
9. Close the hook assembly cover.
32

Part Three | Preparing to Quilt
Task 11 – Threading the Machine
Before threading the machine, make sure you’ve selected quality thread for your project. Choosing the right thread for the machine can prevent the thread from breaking or tangling up under the needle plate. Note the following:
· This machine uses cone-style thread, not thread from a spool. Do not use spool thread unless the spool accessory has been installed.
· Choose thread that is strong enough to pass the yank test, and re-test thread as it ages. Thread strength can diminish over time. a. Hold the cone in one hand and the end of thread in the other.
b. Tug on the thread. If the thread snaps easily, it may be too brittle to use for quilting.
33

Part Three | Preparing to Quilt
Task 11 – Threading the Machine (continued)
The following diagram outlines the path the thread (shown in blue) must take through the machine.
2

1 3
8 4

6

7

5

9

12

10

11

1. Thread Cone 2. Thread Mast Guide Loop 3. Thread Guide Rod 4. Small Thread Tensioner 34

5. Large Thread Tensioner 6. Check Spring 77. Thread Guide 8. Take-up Lever

99. Bottom Thread Guide 1100. Eyelet of Needle Bar 1111. Eye of Needle 1122. Thread Cutter

Part Three | Preparing to Quilt
Task 11 – Threading the Machine (continued)

1. Rotate the hand wheel or press needle up on the display to raise the needle to the top position.
Hand Wheel

34. Pull the thread up, through the thread mast guide loop directly above the thread cone.
Guide Loop

Thread Mast

12. For your safety, press the Menu icon on the display to go to the Settings menu; this prevents the machine from stitching.

45. Feed the thread through the top hole of the thread guide rod. Wrap the thread around to the back of the guide and insert through the bottom hole.

Menu

Thread Guide Rod

23. Slide the thread cone down onto the front thread stand.

56. Run the thread through the top hole on the small thread tensioner. Then slip the thread between the two discs, and through the bottom hole.

Thread Stand

Small Thread Tensioner

35

Part Three | Preparing to Quilt
Task 11 – Threading the Machine (continued)

67. Floss the thread between the discs on the large thread tensioner. Wrap the thread over the check spring.
Check Spring

91.0 Pass the thread down through the bottom thread guide on the way to the needle.

Large Thread Tensioner
78. Next, run the thread under the thread guide next to the large thread tensioner.

Bottom Thread Guide
1101. Now pass the thread through the front of the needle bar eyelet, located above the needle.

Needle Bar Eyelet

Thread Guide

89. Pull the thread through the hole in the take-up lever.
Take-up Lever

1112. Thread through the eye of the needle.

Eye of the Needle
36

Part Three | Preparing to Quilt
Task 11 – Threading the Machine (continued)
11.3 Loop excess thread over the thread cutter on the left of the machine to cut the thread.
Thread Cutter
Congratulations! You have completed Part Three of this manual. If you are assembling a new frame, turn to Part Three of your frame manual. If your frame manual is not broken into parts, follow the manual’s directions to:
· Install and adjust the rails · Install frame handwheel (if applicable) · Install the bungee clamps (if applicable) · Adjust the carriage stop (Cutie Frame only) · Level the frame (if applicable) If you are not assembling a new frame but are installing QuiltMotion onto your frame, turn to Part Three of your QuiltMotion manual. If you are installing your machine onto a frame that is already fully assembled and are not installing QuiltMotion at this time, continue to Part Four of this manual on page 38.
37

Part Four | Preparing to Quilt
Part Four
If your frame isn’t fully assembled at this time, it is recommended to complete Part Three in your frame manual, Part Three in your QuiltMotion manual (optional), and Part Four of your frame manual before you continue. Progress Checkpoint: Have you:
· Installed your frame’s rails. · Adjusted the rails to work with your machine. · Installed frame handwheel (applicable frames only) · Installed bungee clamps (applicable frames only) · Adjusted the carriage stop (Cutie Frame only) · Leveled the frame (applicable frames only) Have you: · Completed QuiltMotion Part Three (optional) Have you: · Prepared your frame for fabric installation · Installed your quilt onto your frame
38

Quilting

Part Four | Quilting

This section of the manual covers how to use your machine to quilt. Choosing Machine Settings …………………………………………………………………… page 40 Using the Handlebar Controls ……………………………………………………………….. page 42 Using the Precise Quilting Mode ……………………………………………………………. page 43 Using the Cruise Quilting Mode ……………………………………………………………… page 45 Using Manual Quilting Mode …………………………………………………………………. page 47 Using Baste Quilting Mode ……………………………………………………………………. page 49 Using the Bobbin Estimator Tool…………………………………………………………….. page 51 Using the Edge Warning………………………………………………………………………… page 53 Adjusting Thread Tension …………………………………………………………………….. page 56 Taking Measurements ………………………………………………………………………….. page 59 Making Calculations ……………………………………………………………………………… page 61 Tracking Stitch Count & Run Time …………………………………………………………. page 62 Getting Started ……………………………………………………………………………………. page 63
39

Part Four | Quilting
Choosing Machine Settings
To customize the settings for the handlebar controls, screen buttons, or warning icons, take the following steps: 1. Press the menu icon in the top right corner of the screen and select Settings.
The Settings menu opens.
Note: Stitching is disabled while the Settings menu is pulled up. 40

Part Four | Quilting
Choosing Machine Settings (continued)
2. Choose desired settings:
· Screen Brightness: Use the sliding button to adjust the brightness of the display. · Needle Area Brightness: Use the sliding button to adjust the brightness of the lamp over
the needle area.
· Needle Button: Choose whether the needle button on the handlebars will create a single stitch or drop or raise the needle.
Single Stitch: Complete motion of needle up and down to create a stitch.
Needle Up/Down: Move the needle either down into the fabric or up out of the fabric. · Needle Stop: Choose whether the needle will default to the “up” or “down” position when
stitching is inactive. · Overspeed Sound: The overspeed alarm can be muted so that there is no beeping when
the machine is moved more quickly than the regulated stitching can manage. · Overspeed Light: The overspeed warning light can be deactivated so that it won’t turn on
when the machine is moved more quickly than the regulated stitching can manage. · Edge Warning Sound: The edge guard alarm can be muted so that there is no beeping
when the machine reaches edge of your set quilting area. · Edge Warning Light: The edge guard warning light can be deactivated so that it won’t turn
on when the machine is moved more quickly than the regulated stitching can manage.. · Click Sound: Choose whether pressing on-screen buttons should make a sound or not. · Stitch Length Units: Choose to display machine stitch length in millimeters per stitch or
stitches per inch. 33. Press the System Info button to access the System Information screen. This screen shows the
display and firmware versions for your machine (see page 83), along with the date of the last firmware update. 44. Press the Factory Reset button to return all settings to their original default status. 55. To return to the main screen, press the X in the top right corner of the settings screen or anywhere outside of the settings screen window.
41

Part Four | Quilting
Using the Handlebar Controls
When first powered up, the machine is in regulated precise quilting mode (see page 45) and can start quilting right away. Please take a moment to review the handlebar controls. These controls are used when quilting. While in the Settings menu, some buttons have a different purpose or do not function (see “Choosing Machine Settings” on page 40 for details).

1

3

4

2
1. Increase: This button increases the number, size, or speed of the stitching, depending upon the quilting mode. For example, in precise quilting mode, this button will increase the number of stitches the machine makes in an inch (SPI) or in a millimeter (SPC).
22. Decrease: This button will decrease the number, size, or speed of the stitching depending upon the quilting mode.
3. Start/Stop Quilting: Press to start or stop stitching. 44. Needle Button: Press to create a single single stitch or to toggle the needle to the up or down
position, based upon settings (see “Choosing Machine Settings” on page 40 for details).

42

Using the Precise Quilting Mode

Part Four | Quilting

The machine defaults to precise quilting mode when turned on. In this regulated quilting mode, you select the stitch length you want and the machine will adjust to help make more consistent stitches as you move the machine faster or slower or change direction. It will only stitch when you move the machine, which helps with patterns that have corners or crisp points.
To reach this quilting mode, press the select quilting mode button and select Precise.

Select Quilting Mode

Jog Needle

Edge Warning Indicator
Start/Pause Stitching
Bobbin Level Estimator

Menu
Needle Up/ Down Button Single stitch
Button

Adjust Stitch Length

Toolbox

To quilt in regulated precise quilting mode, take the following steps:
1. Confirm that the stitch length, measured in stitches per inch or stitches per centimeter, is the desired length. Note: To change units, go to the Settings menu (see page 40).

Use the

symbols or the sliding bar to adjust the stitches per inch. Higher SPI means

shorter stitch length.

2. When stitching is inactive, press the single stitch button or needle up/down button on the display to make single stitches. This can also be done with the stitch button on the right handle, depending on settings. To switch the type of stitch created with the handle button, go to the Settings menu (see page 40).

Note: While stitching is active, the single stitch and needle up/down buttons on the display and the needle button on the handlebar controls are disabled.

43

Part Four | Quilting
Using the Precise Quilting Mode (continued)
13. Position the quilting machine over the quilt. If needed, use the needle jog buttons to move the needle closer or farther from the fabric in small increments to help place your first stitch. · Press to move the needle up or down in small increments.
14. Moving the machine too quickly while quilting can reduce the quality of the stitch regulation. If the machine is moved too quickly, an alarm will sound, a red LED light will shine on the needle area, and the start stitching button on the display will turn red. Slow the machine’s movement to turn off the alarm, light, and display alert. Both the alarm and the display alert can be deactivated in the Settings menu.
25. When activated, the bobbin estimator will show on the left side of the display. For instructions on how to use the bobbin level estimator, see page 51. · When the icon is green, the bobbin is estimated to be between 21% and 100% full. · When the icon is yellow, the bobbin is estimated to be between 11% and 20% full. · When the icon is red, the bobbin is estimated to be under 10% full.
16. When activated, the edge warning indicator will display on the left side of the screen. This indicator will turn red when you reach the edge of the set quilting area. For instructions on how to use the edge warning alert, see page 53.
27. You may find that you need to take measurements or do quick calculations while you quilt. Press Toolbox to access the calculator and measure tools.
38. To deactivate stitching, press the start/stop quilting button on the display or the handlebars. The needle will move into the needle stop position indicated in the Settings menu (see page 40).
44

Using the Cruise Quilting Mode

Part Four | Quilting

Cruise mode is another regulated mode. You select the stitch length you want and the machine will adjust to help make more consistent stitches as you move the machine faster or slower or change direction. However, the machine will continue to stitch in place (at the minimum speed) if you stop moving the machine. This mode is helpful for continuous, smooth, or curvy designs.
To switch to cruise quilting mode, press the select quilting mode button and select Cruise.

Select Quilting Mode

Jog Needle

Edge Warning Indicator
Start/Pause Stitching
Bobbin Level Estimator

Menu
Needle Up/ Down Button Single stitch
Button

Set Minimum Speed

Adjust Stitch Length

Toolbox

To quilt in cruise quilting mode, take the following steps:
1. Confirm that the stitch length, measured in stitches per inch or stitches per centimeter, is the desired length. Note: To change units, go to the Settings menu (see page 40).

Use the

symbols or the sliding bar to adjust the stitches per inch. Higher SPI means

shorter stitch length.

2. Determine the minimum speed the machine will stitch at when stitching is active but the machine is not being moved. This can be set from 5% to 25% of the machine’s top speed of 2600 stitches per minute.

Use the

symbols or the sliding bar to adjust the minimum speed

45

Part Four | Quilting
Using the Cruise Quilting Mode (continued)
13. When stitching is inactive, press the single stitch button or needle up/down button on the display to make single stitches. This can also be done with the needle button on the right handle, depending on settings. To switch the type of stitch created with the handle button, go to the Settings menu (see page 40).
Note: While stitching is active, the single stitch and needle up/down buttons on the display and the needle button on the handlebar controls are disabled. 14. Position the quilting machine over the quilt. If needed, use the needle jog buttons to move the
needle closer or farther from the fabric in small increments to help place your first stitch.
· Press to move the needle up or down in small increments.
15. Moving the machine too quickly while quilting can reduce the quality of the stitch regulation. If the machine is moved too quickly, an alarm will sound and the start stitching button on the display will turn red. Slow the machine’s movement to turn off the alarm and display alert. Both the alarm and the display alert can be deactivated in the Settings menu.
26. When activated, the bobbin estimator will show on the left side of the display. For instructions on how to use the bobbin level estimator, see page 51. · When the icon is green, the bobbin is estimated to be between 21% and 100% full. · When the icon is yellow, the bobbin is estimated to be between 11% and 20% full. · When the icon is red, the bobbin is estimated to be under 10% full.
17. When activated, the edge warning indicator will display on the left side of the screen. This indicator will turn red when you reach the edge of the set quilting area. For instructions on how to use the edge warning alert, see page 53.
28. You may find that you need to take measurements or do quick calculations while you quilt. Press Toolbox to access the calculator and measure tools.
39. To deactivate stitching, press the start/stop quilting button on the display or the handlebars. The needle will move into the needle stop position indicated in the Settings menu (see page 40).
46

Using Manual Quilting Mode

Part Four | Quilting

In this quilting mode, the machine produces stitches at a certain speed. It’s up to the quilter to move the machine the distance needed to get the desired stitch length. This mode is useful for small, continuous patterns.
To switch to manual quilting mode, press the select quilting mode button and select Manual.

Select Quilting Mode

Jog Needle

Edge Warning Indicator
Start/Pause Stitching
Bobbin Level Estimator

Menu
Needle Up/ Down Button
Full Stitch Button

Set Stitching Speed

Toolbox

To quilt in manual quilting mode, take the following steps:
1. Confirm that the stitch speed is set to the desired speed. The speed is measured as a percentage of the machine’s maximum speed of 2600 stitches per minute.

Use the

symbols or the sliding bar to adjust the machine speed

2 When stitching is inactive, press the single stitch button or needle up/down button on the display to make single stitches. This can also be done with the needle button on the right handle, depending on settings. To switch the type of stitch created with the handle button, go to the Settings menu (see page 40).

Note: While stitching is active, the single stitch and needle up/down buttons on the display and the needle button on the handlebar controls are disabled.

47

Part Four | Quilting
Using Manual Quilting Mode (continued)
13. Position the quilting machine over the quilt. If needed, use the needle jog buttons to move the needle closer or farther from the fabric in small increments to help place your first stitch. · Press to move the needle up or down in small increments.
14. When activated, the bobbin estimator will show on the left side of the display. For instructions on how to use the bobbin level estimator, see page 51. · When the icon is green, the bobbin is estimated to be between 21% and 100% full. · When the icon is yellow, the bobbin is estimated to be between 11% and 20% full. · When the icon is red, the bobbin is estimated to be under 10% full.
15. When activated, the edge warning indicator will display on the left side of the screen. This indicator will turn red when you reach the edge of the set quilting area. For instructions on how to use the edge warning alert, see page 53.
26. You may find that you need to take measurements or do quick calculations while you quilt. Press Toolbox to access the calculator and measure tools.
37. To deactivate stitching, press the start/stop quilting button on the display or the handlebars. The needle will move into the needle stop position indicated in the Settings menu (see page 40).
48

Using Baste Quilting Mode

Part Four | Quilting

Use baste mode to create loose, temporary stitches around the edge of your quilt top to hold layers of fabric together while quilting.
To switch to baste quilting mode, press the select quilting mode button and select Baste.

Select Quilting Mode

Jog Needle

Menu

Start/Pause Stitching
Bobbin Level Estimator

Adjust Stitch Size

Toolbox

Needle Up/ Down Button
Single stitch Button

To quilt in baste quilting mode, take the following steps: 1. Confirm that the stitch size, (small, medium, or large) is the desired length.
2. When stitching is inactive, press the single stitch button or needle up/down button on the display to make single stitches. This can also be done with the needle button on the right handle, depending on settings. To switch the type of stitch created with the handle button, go to the Settings menu (see page 40).
Note: While stitching is active, the single stitch and needle up/down buttons on the display and the needle button on the handlebar controls are disabled.

49

Part Four | Quilting
Using Baste Quilting Mode
13. Position the quilting machine over the quilt. If needed, use the needle jog buttons to move the needle closer or farther from the fabric in small increments to help place your first stitch. · Press to move the needle up or down in small increments.
14. Moving the machine too quickly while quilting can reduce the quality of the stitch regulation. If the machine is moved too quickly, an alarm will sound and the start stitching button on the display will turn red. Slow the machine’s movement to turn off the alarm and display alert. Both the alarm and the display alert can be deactivated in the Settings menu.
25. When activated, the bobbin estimator symbol will show on the left side of the display. For instructions on how to use the bobbin level estimator, see page 51. · When the icon is green, the bobbin is estimated to be between 21% and 100% full. · When the icon is yellow, the bobbin is estimated to be between 11% and 20% full. · When the icon is red, the bobbin is estimated to be under 10% full.
16. Edge Warning is automatically deactivated in Baste Mode 27. You may find that you need to take measurements or do quick calculations while you quilt. Press
Toolbox to access the calculator and measure tools. 38. To deactivate stitching, press the start/stop quilting button on the display or the handlebars. The
needle will move into the needle stop position indicated in the Settings menu (see page 40).
Note: Edge warning is inactive while in the baste quilting mode.
50

Using the Bobbin Estimator Tool

Part Four | Quilting

The bobbin estimator calculates the likely amount of thread remaining on the bobbin. To achieve the closest estimate, information must be accurately entered into the Bobbin Estimator screen. Take the following steps to use the bobbin estimator tool:
1 To access the bobbin estimator tool, tap on the Toolbox at the bottom of any quilting mode screen and select the bobbin estimator.

2 Press Select Bobbin. The drop-down menu will show a list of any bobbins you’ve added in the past. To add a bobbin, press Add Bobbin. An on-screen keyboard will appear so you can name the new bobbin.
Tip: Choose a bobbin name that will make it easy to identify which bobbin you’re using so that if you have to swap between partially used bobbins you can be sure to select the correct one from the list.
Name examples: “Ct Light Blue” for light blue cotton, or “Poly Wht 40 Wt” for 40-weight white polyester.
3 Enter the estimated number of yards on the bobbin. As a starting reference, an M-class bobbin fully wound with 40 wt cotton thread is approximately 90 yards. Yardage will vary depending on the fiber and weight of the thread used.
Tip: It may take some practice to estimate the length of a fully wound bobbin. Keep a record of your starting estimate. When you run out of bobbin thread, open the estimator tool and see how much thread remains. Use this information to adjust your starting estimate next time you use the same type of thread.
51

Part Four | Quilting
Using the Bobbin Estimator Tool (continued)

4 Turn on the bobbin estimator with the switch on underneath the bobbin image. When on, any stitches the machine makes will subtract from the estimated thread remaining.

5 When the bobbin thread is used up, you can either delete the record of the bobbin or reset it to be used again. Reset is recommended if you’re planning on winding the bobbin back up with the same thread.
Press Reset to restore the estimated thread remaining to the full estimate.

The bobbin estimator symbol will also show on the left side of the quilting mode screen when the estimator is on. Color changes notify when the bobbin is estimated to be nearing the end of the thread.
Bobbin Estimator Symbol

To delete a bobbin, select it from the dropdown and press delete.

21% – 100% remaining
11% – 20% remaining
0% – 10% remaining

Note: Pressing this symbol on a quilting screen will bring up the bobbin estimator tool.

6 To return to the main quilting screen, press the X in the top right corner or press anywhere outside of the bobbin estimator screen.

52

Using the Edge Warning

Part Four | Quilting

The edge warning helps you stay within a “safe area” of your quilt by alerting you when you approach the edge of boundaries you’ve set. Use this tool to avoid hitting the frame rails or to restrain your quilting to a particular section or block.

Note: Edge Warning is automatically deactivated in Baste Mode, so the alarm will not bother you while tacking down your quilt.

Take the following steps to use the edge warning tool:
1 To access the edge warning tool, tap on the Toolbox at the bottom of any quilting mode screen and select Edge Warning.

2 Move your machine so that your needle is at the top left corner of the area you want to mark as your safe area. Press the set button. Tip: You can also use the start/stop quilting button on the right handlebar to set the corners of the “safe area.”
Set
53

Part Four | Quilting
Using the Edge Warning (continued)
3 Move your machine so that your needle is at the bottom right corner of the area you want to mark as your safe area. Press the set button.
4 After marking your boundaries, set the machine to notify you when your needle is within 1/2 inch or 1 inch of any of those boundaries. Once this is set, a green check mark will appear to confirm everything saved successfully. Note: The edge warning symbol will also appear on the main quilting screen. Pressing this symbol on the main quilting screen will bring up the edge warning tool.
5 To return to the main quilting screen, press the X in the top right corner or press anywhere outside of the edge warning screen.
54

Part Four | Quilting
Using the Edge Warning (continued)
6 Whenever you approach or cross the boundaries while quilting, an alarm will sound, a red LED light will shine on the needle area, and the edge warning symbol on the left side of the main quilting screen will turn red. These alerts persist until you return to the established “safe area.”
Note: Edge Warning is automatically deactivated in Baste Mode. 7 The light and the alarm can each be deactivated in the settings screen (see page 40).
To hide the edge warning symbol on the quilting screen, turn off the edge warning tool from the edge warning screen. This will also deactivate the warning light and alarm.
55

Part Four | Quilting
Adjusting Thread Tension
Proper thread tension prevents unwanted puckering, poorly-formed stitches, and malfunctions that can damage the fabric. Test your thread tension on extra materials before sewing on a project. Tip: Bottom thread tension is the foundation for proper thread tension, and should be set first before setting top tension. Bottom tension is addressed in “Task 10 – Loading the Bobbin Case” on page 30.
Large Thread Tensioner

1. Loosen the tension knob on the large thread tensioner to set the tension to “1.” The bottom of the tension knob lines up with the number that the tension is set to.

4 3 21

Tension Knob

Note: Setting “1” is the lowest tension for the machine. This is an ideal starting place to find the correct top thread tension. Take care not to go past one: the tension knob may unscrew completely and fall off the machine.
56

Part Four | Quilting
Adjusting Thread Tension (continued)
2. Slowly increase the tension while stitching into scrap material similar to your project. When the thread tension is balanced, the top and bottom thread will knot in the middle of the fabric layers.

Too Much Top Tension

Bottom thread is pulled to the top
of the fabric.

Balanced Tension

Too Little Top Tension

Top thread is pulled to the bottom of the
fabric.
57

Part Four | Quilting
Adjusting Thread Tension (continued)
· If the bobbin (bottom) thread is pulled through the top layer of fabric, there is too much top tension. Loosen the tension by turning the large thread tensioner knob counter-clockwise toward the setting “1.”
4 3 21
· If the top thread is pulled down through the bottom layer of fabric, there is too little top tension. Increase the tension on the top by turning the large thread tensioner knob clockwise toward setting “4.” Stop turning knob when desired tension is achieved.
4 3 21
58

Taking Measurements

Part Four | Quilting

Your machine can be used to take measurements across the surface of your quilt.

1 To access the measure tool, tap on the Toolbox at the bottom of any quilting mode screen and select Measure.

2 Select whether you want to measure using inches or centimeters.

3 Move the machine so that the needle is at the position where you want to start your measurement and click the Reset Origin button. This origin will be saved until you reset it again.
59

Part Four | Quilting
Taking Measurements (continued)
4 Move the machine so that the needle is at the end point of your measurement. Press Hold to stop measuring and freeze the current measurements on screen. Measures the actual distance from the origin to the end point.
Measures the horizontal distance from the origin.
Measures the vertical distance from the origin.

Tip: You can also use the buttons on the right handlebar to reset the origin and hold the measurements.

Reset Origin

Hold

5 To resume measuring, press Hold a second time.
6 To return to the main quilting screen, press the X in the top right corner or press anywhere outside of the measure screen.

60

Making Calculations

Part Four | Quilting

Your machine can be used to make quick calculations.
1 To access the calculator, tap on the Toolbox at the bottom of any quilting mode screen and select Calculator.

2 Use the calculator to add, subtract, multiply, divide, and find percentages.

3 To return to the main quilting screen, press the X in the top right corner or press anywhere outside of the calculator screen.
61

Part Four | Quilting
Tracking Stitch Count & Run Time
Use the project tool to track the stitch count and run time over the lifetime of your machine, or for individual projects. 1 To access the project tool, tap on the Toolbox at the bottom of any quilting mode screen and
select Project.
2 The stitch tracking screen displays. Lifetime shows the hours the machine has spent running and the number of stitches it has made since it was manufactured. “Project” shows the hours and minutes run and number of stitches created since the counter was last reset.
Press to reset project counter to 0 hours and 0 stitches.
Tip: It’s recommended to oil your machine after 20 hours of use. The “Hours Run” counter can help keep track of when your machine is due to be oiled. After cleaning and oiling your machine, press Reset to start the counters under project back at zero. The counters under lifetime cannot be reset.
62

Getting Started

Parts & Tools Needed:

Scissors (not included)

Washable Fabric Marker/chalk (not
included)

Part Four | Quilting

Instructions
With the machine fully assembled, you are ready to begin quilting. Practice on spare fabric to become familiar with the machine’s settings and movements so you can start your projects with confidence. It is normal to make mistakes, so don’t get discouraged if your stitches don’t look perfect right away. Follow the steps in this section to get started and you’ll be quilting in no time!
1 Relax! Take a deep breath and don’t be afraid to take it slow.
Make sure that the following items have been completed: · Your machine is threaded and tensioned. · Your practice fabric is attached. · You have established any machine settings you want to use.
2 Before you begin stitching, pull up your bobbin thread to prevent the thread tail from dangling underneath the fabric as you quilt and getting sewn in place.
a First, position the needle directly above where you want to begin your pattern.
b Pull on the top thread so that it is tight and jog the needle up and down using the single stitch button on the display.
Top Thread

63

Part Four | Quilting
Getting Started (continued)

c While still tightly holding the top thread, move the machine several inches to the side. Your top thread should pull a loop of bobbin thread through the start point to the top of the fabric.

3 Secure your stitches and get quilting. Be sure to start as close as possible to the point where you pulled out the bobbin thread.

Bobbin Thread

Start Point
d Pull on the loop of bobbin thread until the loose end of the thread comes up from underneath the fabric.

4 With fabric chalk or a marker, draw a simple pattern or write your name on the fabric and then stitch over it to practice.

Bobbin Thread

e Pull on the bobbin thread while moving the machine back to the start point. This makes sure that there is no loose thread underneath the fabric.

Grace

64

5 Complete the pattern by making a tie-off stitch. Use the single stitch button to make a
few small stitches very close together.

Part Four | Quilting
Getting Started (continued)
c Make a single stitch over the tie-off.

6 To pull up the bobbin thread after making a tie-off, take the following steps:
a Move the machine away from the tie-off stitch.

d Hold the loop and move the machine away from the tie-off again.

b Hold the thread to make a loop and return the machine to the tie-off stitch.

e Keep moving away from the tie-off until a loop of bobbin thread is pulled up
above the fabric. Cut all threads close to
the tie-off.

65

Part Four | Quilting
Getting Started (continued)
7 You may now cut the thread tails from the beginning of the pattern.
Practice! Keep trying different stitches until you feel comfortable with how your machine feels and moves. You can always attach a new piece of practice fabric if you need to.
Congratulations! Now that you have practiced and gotten used to the basic settings and movements of your machine, you are ready to begin your quilting journey. Good luck, and thank you again for choosing The Grace Company to help with your quilting needs.
66

Part Four | Maintaining the Machine
Maintaining the Machine
This section of the manual covers important machine maintenance and care procedures. Preparing the Oil Bottle ………………………………………………………………………… page 68 Oiling and Cleaning ……………………………………………………………………………… page 69 Changing the Needle ……………………………………………………………………………. page 72 Adjusting the Hopping Foot ………………………………………………………………….. page 74 Reinstalling the Needle Plate…………………………………………………………………. page 79 Re-assembling the Thread Tensioner ……………………………………………………… page 81
67

Part Four | Maintaining the Machine
Preparing the Oil Bottle

Parts & Tools Needed:

Oil Bottle

Scissors

3. Peel the safety foil off the opening of the oil bottle.

Power Cord/Oil Bottle Box

(Not included)

Instructions
Take the following steps to prepare the oil bottle for use in oiling the machine.

1. Snip off about 1/4th of an inch from the tip of the plastic lid with a pair of scissors.

4. Carefully screw the lid onto the oil bottle.

2. Place the applicator needle onto the top of the cap.

5. Hold bottle upside down and squeeze gently to apply oil. When not in use, cover the applicator needle with the safety cap.

68

Oiling and Cleaning

Parts & Tools Needed:

Oil Bottle

Lint Brush (Tools Box)

Part Four | Maintaining the Machine

· Compressed Air Can (optional; not included)

Instructions Oil and Clean:
Machine
Hook Assembly

· At the start of a new project · After 20 hours of use · After sitting without use for more than 30 days
· Every other bobbin change

Tip: The “Hours” counter on the Projects screen can be used to track hours of quilting time (see page 62).

Take the following steps to clean and oil the machine:

1. Power off the machine.

2. Set the large thread tensioner to “1” to expose the tensioner discs. Use the lint brush or a can of compressed air to clear away lint and thread remnants.
Note: Lint build-up between the tensioner discs can prevent proper thread tensioning.

4 3 21

Large Thread Tensioner

69

Part Four | Maintaining the Machine
Oiling and Cleaning (continued)

13. Clear debris from the spring and discs of the 67. In and around the hook assembly, clear

small thread tensioner.

away any lint, cloth, and thread remnants.

Hook Assembly

Small Thread Tensioner

34. Pull the release lever (shown in blue) on the bobbin case to remove it from the hook assembly. If the case won’t release, raise the needle with the hand wheel at the rear of the machine.

78. Rotate the hand wheel until the needle is halfway down. This will put the hook in the best position for oiling. Hand Wheel

54. Set the bobbin aside. Clean the bobbin case with the lint brush or compressed air. Be sure to clean the area under the bobbin tension thread arm.

89. Place 1-2 drops of oil into the hook assembly between the inner part (shown in gray) and outer part (shown in blue).
1-2 Drops

Bobbin Thread Tension Arm

70

9 Unplug the display from the port on the machine.

Part Four | Maintaining the Machine
Oiling and Cleaning (continued)
1.2 Power up the machine. Run the machine in manual or cruise stitching modes without a bobbin installed for about 10 seconds. This will distribute the oil in the hook assembly without getting oil on your bobbin thread.

Display Port

110. Pull the tab on the display board cover to remove it from the machine.

130. Reload the bobbin case and return it to the machine (for detailed instructions on tensioning the bobbin case, see page 30). Close the hook assembly cover.

Display Board Cover
Tab

121. Place 1-2 drops of oil on the needle bar. Then replace the display board cover and plug the display back into the port.

1.4 Wipe down the needle bar regularly to prevent oil from accumulating and dripping onto your quilt.

Needle Bar

1-2 Drops 71

Part Four | Maintaining the Machine
Changing the Needle
Parts & Tools Needed:

Needle

Needle Magnet

For information on selecting a needle, see page 97.

Instructions
A broken, bent, or burred needle may break thread, damage fabric, or even damage the machine.
Always check that the needle is in good repair before starting a new project, and replace the needle after eight hours of use.

Straight Needle

Bent Needle

To avoid damage to the machine, please choose an approved needle style from the list below: · DPx5 MR · 134 MR · 1955 MR
To change the needle, take the following steps:
1. Power off the machine.

2. With the hand wheel, raise the needle so it clears the hoop part of the hopping foot.
Hand Wheel

3. Loosen the needle thumb screw and pull down the needle. If needed, use a flat-head screwdriver.
Needle Thumb Screw

72

54. Insert the new needle all the way into the needle bar. Check the needle bar sight hole above the thumb screw to make sure the needle is inserted all the way.

Part Four | Maintaining the Machine
Changing the Needle (continued)
87. Hand-tighten the thumb screw. Do not over-tighten if using the flat-head screwdriver.

Needle Bar Sight Hole

Needle
65. The scarf, a cut-out on the back of the needle, should face the throat of the machine. Place the needle magnet on the opposite side of the scarf. Needle Magnet
Scarf

76. Use the needle magnet as a visual guide.
Twist the needle until the magnet points as
straight out from the machine as possible.
Note: Do not attempt to adjust the needle by moving the magnet directly.

73

Part Four | Maintaining the Machine
Adjusting the Hopping Foot

Parts & Tools Needed:

T-handle Allen Wrench 3 mm
3 mm

Hopping Foot Height Tool

Height Adjustment
When quilting with thick fabric or batting layers, the hopping foot may pressing down on the quilt too tightly and begin to drag. Alternatively, if the hopping foot is set too high, skipped stitches can result. The hopping foot can be raised or lowered to correct these problems. To adjust the hopping foot height, take the following steps:

1. With the hand wheel, raise the needle so it clears the hoop part of the hopping foot.
Hand Wheel

23. Slide the hopping foot height tool underneath the hopping foot so that the needle slides into the height tool groove.
Hopping Foot

Hopping Foot Height Tool

2 With the 3 mm Allen wrench, loosen the hopping foot screw that holds the hopping foot to the hopping foot collar.
Hopping Foot Collar
Hopping Foot Screw

Note: The height tool prepares the machine for standard sized quilt batting and two layers of fabric. For thicker quilts, stack sheets of printing paper over the gauge to increase room underneath the hopping foot.
34. Re-tighten the hopping foot screw.
Hopping Foot Screw

74

Part Four | Maintaining the Machine
Adjusting the Hopping Foot (continued)

Rotation Instructions
The hopping foot can be rotated to improve line of sight. To rotate the hopping foot, please take the following steps.

1. Power off the machine.
2. Rotate the hand wheel to lift the needle to the highest position.

5. With the 3 mm Allen wrench, loosen the collar screw that holds the hopping foot collar to the presser bar.

Hand Wheel

Collar Screw

Hopping Foot Collar

3. Use the 3 mm Allen wrench to remove the screw holding the hopping foot.

6. Drop the hopping foot collar below the presser bar and turn it to the desired position.

Hopping Foot Screw

4. Slide the hopping foot from the presser bar.

The hopping foot can be set to two positions:

Hopping Foot 75

Part Four | Maintaining the Machine
Adjusting the Hopping Foot (continued)
7. Lift the hopping foot collar back up to the presser bar, and re-tighten the collar screw.
Collar Screw

8. Slide the hopping foot into the collar and screw in place with the hopping foot screw.

Hopping Foot Screw

Hopping Foot

9. Set the hopping foot height (see page 74).

76

Part Four | Maintaining the Machine
Adjusting the Hopping Foot (continued) Removal Instructions
To remove the hopping foot for maintenance or to adjust the hopping foot angle, take the following steps: 1. Power off the machine. 2. With the hand wheel, raise the needle so it clears the hoop part of the hopping foot. 33. Use the 3 mm Allen wrench to remove the hopping foot screw.
Hopping Foot Screw
The hopping foot should now slide free from the presser bar.
Hopping Foot
77

Part Four | Maintaining the Machine
Adjusting the Hopping Foot (continued)
Installation Instructions
To install the hopping foot on your quilting machine, please take the following steps: 1. Power off the machine. 2. Slide the hopping foot to the slot in the hopping foot collar. Use the 3 mm Allen wrench and
hopping foot screw to tighten in place.

Hopping Foot Collar

Hopping Foot Screw
Hopping Foot

3. Adjust height as needed (see page 74).

78

Reinstalling the Needle Plate
Parts & Tools Needed:

Part Four | Maintaining the Machine

Flat-head Screwdriver
Removal Instructions
To remove the needle plate from the quilting machine, take the following steps: 1. Power off the machine and raise the needle to the highest position using the hand wheel. 2. Use the flat-head screwdriver to remove the two needle plate screws.
Needle Plate Screw (x2)
Needle Plate

3. Slide the needle plate from the machine. 79

Part Four | Maintaining the Machine
Reinstalling the Needle Plate (continued)

Installation Instructions
To install the needle plate onto the quilting machine, take the following steps:

1. Power off the machine. Raise the needle to the highest position using the hand wheel.
Hand Wheel

4. Place the two needle plate screws (shown
in gray) into the plate. Make sure the needle
plate is centered around the needle, and
then tighten the screws with the flat-head screwdriver.

2. Align the screw holes on the needle plate with those on the machine.

Needle Plate

3. Slowly lower the needle with the hand wheel. The needle should slide into the center hole of the needle plate without contacting the plate.

15. Reset the hopping foot height using the
height gauge. See “Adjusting the Hopping Foot” on page 74 for instructions.

80

Part Four | Maintaining the Machine
Re-assembling the Thread Tensioner
Instructions
If you over-loosen the large thread tensioner knob, the tensioner may come apart and need to be reassembled.

1

2

3

4

5

6

7

1. Tensioner Disc 2. Tensioner Disc

33. Meter Key 44. Meter

5. Spring 66. Keyed Washer

77. Knob

Note: Place the tension discs so the curved sides face each other.

Note: Install the keyed washer so the grooved side faces toward the knob.
81

Part Four | Repairs and Diagnostics
Repairs and Diagnostics
The instructions in this section should only be taken at the direction of a Grace Company support technician. If you are experiencing problems with your machine, please contact our technical support team:
· Phone: 800-264-0644 · Email: support@graceframe.com
Checking the Firmware …………………………………………………………………………… page 83 Troubleshooting Bobbin Wind…………………………………………………………………….. page 84 Replacing the Encoder Spring ………………………………………………………………….. page 86 Reinstalling the Hook Holder …………………………………………………………………… page 89 Timing the Machine ………………………………………………………………………………… page 92
This section of the manual covers replacing the encoder spring, installing the hook holder, timing the machine, and checking the firmware versions of the machine and display.
82

Checking the Firmware

Part Four | Repairs and Diagnostics

The firmware versions for the machine and the display are found by pressing “System Info” from the bottom of the Settings menu (see page 40).

Update Display Version

.#.# #X##

XX/XX/XX

Date of Machine Firmware

The following information and options display: · Display Version: Shows the software version for the touch display. · Machine Firmware: Shows the firmware version for the machine. · Date: Shows the date when the machine firmware was last updated. · Update Button: Checks to see if an SD card with an available software update has been inserted into the display. If it detects the update, it will update the display to the newest version. · OK Button: Click to return to the Settings menu.
83

Part Four | Repairs and Diagnostics
Troubleshooting Bobbin Wind
A quality bobbin wind is essential for a properly functioning machine and for setting your baseline thread tension. The thread on the bobbin should be smooth and evenly wound. The threads should be tightly packed together.
Bobbin Wound Too Loose
The tension of the bobbin wind is determined by the bobbin thread tensioner. Turn the knob one full rotation clockwise and re-test the bobbin wind. Repeat until the bobbin wind is tight and smooth.
Bobbin is Filling to One Side
If the bobbin is filling to one side, the bobbin thread tensioner is positioned incorrectly and will need to be adjusted.
1. Determine the whether the bobbin is filling more toward the top or the bottom.
84

Part Four | Repairs and Diagnostics
Troubleshooting Bobbin Wind (continued)
12. Unthread the bobbin thread tensioner. With a 7 mm wrench or needle-nose pliers, loosen the nut at the base of the tensioner.

Nut
13. Turn the top part of the tensioner assembly (shown in blue) a full rotation to adjust the height of the tension discs.
If the bobbin is filling more toward the top, turn the tensioner one full rotation clockwise and re-test.
If the bobbin is filling more toward the top, turn the tensioner one full rotation counter-clockwise and re-test.
14. Once the bobbin is filling correctly, re-tighten the nut. Make sure the thread guide is on the correct side of the tensioner assembly.

Nut

Thread Guide

85

Part Four | Repairs and Diagnostics
Replacing the Encoder Spring
Parts & Tools Needed:

Please speak to a Grace Company support technician before
attempting these instructions.

Upper Encoder Spring (Silver)
OR

Lower Encoder Spring (Black)

T-handle Allen Wrench 2.5 mm
2.5 mm

T-handle Allen Wrench 4 mm
4 mm

Instructions
If the encoder spring is over-tensioned, it may break and need to be replaced. To replace the encoder spring, take the following steps:

1. Determine the correct spring to use in the repair:
Upper Encoder: Attached to the wheel on the machine. Use the silver spring. Lower Encoder: Attached to the wheel on the bottom carriage. Use the black spring.

3. Loosen the lock collar screw with the 2.5 mm Allen Wrench until the lock collar (shown in blue) can twist freely.

Lock Collar Screw

2. Unplug the encoder cable from the machine.

14. Use the 4mm Allen wrench to loosen the encoder screw and remove the encoder and wheel.

Encoder Port

Encoder Screw 86

Part Four | Repairs and Diagnostics
Replacing the Encoder Spring (continued)
15. Remove the plastic stop, wheel spacer, washer, broken encoder spring, and shoulder spacer from the encoder.

Plastic Stop

Wheel Spacer

Washer

Encoder Spring

Shoulder Spacer

26. Pull on the lock collar to remove it from the encoder screw.

48. Place the long arm of the encoder spring arm into the hole on the encoder lock collar.

Lock Collar

Long Spring Arm

Lock Collar

37. Place the replacement spring over the encoder screw, and insert the short arm of the spring all the way through the hole on the encoder base.
Short Spring Arm

59. Without allowing the arm to slip out of the lock collar, rotate the collar until it wraps around the encoder bolt.

87

Part Four | Repairs and Diagnostics
Replacing the Encoder Spring (continued)

11.0 Adjust the screw and lock collar so the head 113. Complete the assembly instructions for the

of the screw slides in between the lock collar.

encoder you repaired.

For the upper encoder (silver spring) assembly instructions, see page 22.

For the lower encoder (black spring) assembly instructions, see page 2.

11 Slide the shoulder spacer onto the screw with the thinner side toward the head of the bolt.
Shoulder Spacer

12 Next, place the washer, wheel spacer, and plastic stop onto the encoder screw.
Plastic Stop

Wheel Spacer

Washer

88

Reinstalling the Hook Holder

Parts & Tools Needed:

T-handle Allen Wrench 3 mm
3 mm

Flat-head Screwdriver

Part Four | Repairs and Diagnostics
Please speak to a Grace Company support technician before
attempting these instructions.

Removal Instructions
The hook holder keeps the hook assembly in place. The following procedure should only be attempted if determined necessary by a Grace Company support technician. If done incorrectly, major machine problems can result. Please call 800-264-0644 before attempting this procedure.
1. Turn off the machine.

2. Rotate the hand wheel to raise the needle to the highest point.
Hand Wheel

4. With the 3 mm Allen wrench, remove the hook holder screw (shown in gray) that attaches the hook holder to the machine.

Hook Holder Screw

3. Press in on the hook assembly cover and down to open it.

5. The hook holder will fall free of the machine.

Hook Holder

89

Part Four | Repairs and Diagnostics
Reinstalling the Hook Holder (continued)

Installation Instructions
1. Turn off the machine. 2. Rotate the hand wheel to raise the needle
to the highest point.
Hand Wheel

5. Turn the inside part of the hook assembly (shown in blue) so that the positioning guide is at the highest point.
Hook Assembly Positioning Guide

3. Remove the needle plate using the flat-head screwdriver (see page 79).

66. Slide the finger of the hook holder into the middle of the hook assembly’s
positioning guide.

Hook Holder

4. Remove the bobbin case from the hook assembly (see page 30).

7 Attach loosely with the hook holder screw. Do not tighten.

90

Part Four | Repairs and Diagnostics
Reinstalling the Hook Holder (continued)
18. Align the hook holder with the inside edge of the positioning guide, as shown below.
9 Tighten the hook holder screw to fasten the hook holder in place. The inside part of the hook assembly should no longer rotate freely by hand.
10 Re-install the needle plate. See page 79 for instructions.
91

Part Four | Repairs and Diagnostics
Timing the Machine
Parts & Tools Needed:

Flat-head Screwdriver

T-handle Allen Wrench 2 mm
2 mm

Please speak to a Grace Company support technician before
attempting these instructions.
Timing Spacer Tool

Instructions
Timing your machine aligns the needle and hook assembly so that they are in the correct places during the creation of a stitch. Improper timing can result in damage to the machine and needle, or make sewing impossible. Please consult with a Grace Company support technician before attempting to adjust the timing on your machine.

1. Turn off the machine.
2. Check that your needle is not bent or damaged, and that it is inserted all the way into the needle bar (see page 72).

34. Remove the needle plate (see page 79).

Needle Bar Sight Hole

Needle
13. Remove the bobbin case from the hook assembly (see page 30).

45. Look into the machine’s timing cut-out and turn the hand wheel. The hook assembly will rotate.

Timing Cut-out

Hook Assembly

92

Part Four | Repairs and Diagnostics
Timing the Machine (continued)

56. As each of the 3 set screws aligns with the timing cut-out, loosen them with the 2 mm Allen wrench.

89. Stop raising the needle once the eye is about level with the hook (shown in blue). Do not continue to raise the needle. If the needle goes too high, start over at step 8.

Set Screw (x3)

67. The outside part of the hook assembly (shown in blue) now rotates by hand. Turn the outside part of the hook assembly so that the hook is at the top.

91.0 Slip the timing spacer tool (shown in blue)
into the hook assembly with the flat side facing up. Then turn the timing tool until the
flat side faces down.

Hook

78. Hold the hook in place and carefully rotate the hand wheel counter- clockwise to drop the needle (shown in gray) to its lowest point. Continue rotating the hand wheel the same direction. The needle should begin to raise up.

91.1 Turn the hand wheel the clockwise to bring the needle back down until it rests on top of the timing spacer. Do not let the needle rise to the top before bringing it back down or you will need to repeat steps 8-11.

Needle

93

Part Four | Repairs and Diagnostics
Timing the Machine (continued)
11.2 Position the tip of the hook (shown in blue) with the center of the Needle Scarf (shown in gray). This is easier to see from the back of the machine.

13 Pull the hook assembly toward the front of the machine until the hook is as close to the needle as possible without touching.

21.4 Use the 2 mm Allen wrench to tighten one of the three set screws through the timing cut-out window on the left.

Set Screw

94

Part Four | Repairs and Diagnostics
Timing the Machine (continued)
11.5 Turn the timing spacer tool until the flat side is facing up and then remove it from the machine.
116. Turn the hand wheel a full rotation to listen for clicking noises and to ensure the needle does not bend or hit the hook
117. Tighten the two remaining set screws through the timing cut-out. Set Screw (x2)
18 Replace and align the needle plate (see page 79). 19 Replace the bobbin case (see page 30). 20 Test the machine and listen for any unusual noises. If there are any skipped stitches, the hook is
too far away from the needle. If the thread breaks, the hook is too close to the needle.
95

Appendix
Appendix
This section of this manual covers additional information on quilting with your machine. Choosing Your Needle …………………………………………………………………………………..page 97 Choosing Your Thread …………………………………………………………………………………..page 99 Choosing Your Fabric and Batting …………………………………………………………………page 102 Troubleshooting Guide ………………………………………………………………………………..page 103 Index ………………………………………………………………………………………………………..page 105
96

Choosing Your Needle

Appendix

Using the wrong type of needle, or using a needle that is bent, broken, or blunt, can damage the fabric, the machine, and needle. For best results:
· Use the recommended needle style for your machine (see below). · Use the needle size appropriate for the weight and type of thread you’re using (see below). · Never use a needle that is dull, bent, burred, or damaged. · Use multi-directional needles. · Change your needle after 8 hours of use and at the beginning of each project.

Needle Style
The following are the recommended needle styles for your machine:
· DPx5 MR · 134 MR · 1955 MR

Needle Sizes
Choose the size of your needle based upon the thread you’re using. Thicker thread requires a thicker needle. Remember, the thicker the thread, the lower the thread weight (wt.) number.

Needle Size 14 / 90

Thread Size and Type
· mono-filament · 100 wt. silk · 60 wt. polyester

16 / 100

· mono-filament · 60 wt. polyester or cotton
· 50 wt. cotton

18 / 110 20 / 125

· 50 wt. polyester · 40 wt. cottons and polyester · 30 wt. cotton and polyester
· 30 wt. or heavier of any thread

97

Appendix
Choosing Your Needle (continued) Needle Diagram
Needle Front View

Needle Side View

Shank

Groove

Shaft
Eye Point

Scarf

· Shank: Where the needle bar grasps the needle.
· Shaft: The long, narrow part of the needle. Needle size is based upon the diameter of the needle shaft.
· Groove: Reaching from the top to the bottom of the needle shaft, the groove allows thread to pass through the fabric more easily and without getting damaged.
· Eye: Hole near needle point where the needle is threaded.
· Scarf: A cut-away on the back of the needle that allows the needle to fit smoothly within the hook assembly when quilting.
· Point: The sharp end of the needle. Choose the type of needle point to fit your project, and always replace your needle once the point is dull.

98

Choosing Your Thread

Appendix

Choosing the best thread for your project is just as important as choosing the correct needle. Good thread is strong and can pass the “Yank Test” (see page 33). It holds its color well over time (colorfast), and uses long fibers (extra-long staple) that resist creating lint.
Thread type and size determines not only which needle size to choose and what the thread tension must be set to on your machine, but also how visible the thread is on the project.
For best results:
· Use a cone-style thread unless you have the thread spool accessory for your machine. · Test the strength of thread before use with the “Yank Test” (see page 33). · Practice using new thread on spare quilting materials to find the ideal thread tension. Write this
information down and store it with your thread for later reference. · Keep thread out of sunlight to prevent fading, and do not store near extreme temperatures. · Select thread that is ideal for the fabric you’re using (see the chart below). · Use similar thread for top and bottom thread.

Thread Type Guide
Threads can be multiple strands, called ply, spun together, or they can be single ply. The fibers that make up the ply can come from many sources, but the most common threads used in quilting are made from cotton, polyester, and silk. The unique properties of each material make some threads better suited for use on some fabrics than others.

Thread Type Ideal Fabric

Cotton Polyester

· Cotton · Linen · Rayon
· Knit or Stretch · Woven synthetic

Silk

· Silk

· Wool

· Basting thread for all fabrics

99

Appendix
Choosing Your Thread (continued)
Thread Size
The thickness of the thread is called the weight (wt.). This number is usually stamped on the edge of the top or bottom of the thread cone. Notice that as the thread becomes heavier and thicker, the weight decreases:
· 60 weight: Very thin, fine thread that will blend in to the fabric. · 40 weight: Thicker thread that will show up on the fabric. Note: Choose matching weight and thread type when picking top and bottom (bobbin) threads.
Tip: Not all manufacturers will have the same sizing method for their thread. Threads can be measured by weight, tex, denier, or scaling that is unique to its brand. Take the time to understand how the sizing works for a brand you’re considering, and keep a few common sewing rules in mind:
· The thicker the thread, the larger the needle required. A needle that is too thin can shred thread.
· The thinner the thread, the smaller the needle should be. A needle that is too large will cause uneven stitching and can leave holes in the fabric.

Thread Processing
Sometimes thread is processed to change its properties. The chart below lists the processes common to cotton and polyester. No extra processing or treatments are typical for silk.

Thread Type Processing

Cotton

· Mercerized: Treated to improve strength and colorfastness.
· Glazed: Waxed or coated to give a polished appearance. The coating may rub off and build up in machine.
· Gassed: Exposed briefly to a gas flame to burn away fuzz and lint, giving a smooth appearance.

Polyester

· Lubricated: Treated with lubricant to reduce friction. Avoid thread that is oily to the touch.
· Bonded: Treated with resin to increase strength. This is typically used for heavy-duty applications, such as upholstery.

100

Appendix
Choosing Your Thread (continued)

Our Recommended Thread

Finesse thread is specially-designed for quilting by the Grace Company. It can be used with domestic (sewing) and quilting machines, and comes in 60 colors.

· 100% Polyester, 3-ply thread · 1,500 yards mini-cone · 50 wt.

· 110/18 or 100/16 quilting machine needle · Topstitch 90/14 sewing machine needle

3283 Snow White

3293 Charcoal

2979 Rainbow

2989 Prism

2999 Cherry Blossom

3009 Deep Forest Green

3284 Pearl White

3294 Midnight Blue

2980 Sunny Spring Day

2990 Tropical Sunset

3000 Candy Apple

3010 Vintage Turquoise

3285 Light Wool

3295 Obsidian

2981 Strawberry Lemonade

2991 Aurora Lights

3001 Pomegranate

3011 Seaside Teal

3286 Ice Blue

3296 Marigold

2982 Pastels

2992 Mango Salad

3002 Dusk Rose

3012 Ocean Wave

3287 Pink Rose

3297 Leafy Green

2983 Raspberry Ice

2993 Camp Fire

3003 Cotton Candy

3013 Bright Blue Sky

3288 Lilac

3298 Blue Sapphire

2984 Circus Tent

2994 Mountain Jungle

3004 Tangerine Punch

3014 Lavender Blossom

3289 Light Sand

3299 Magenta

2985 Twilight Pink

2995 Desert Flower

3005 Grapefruit

3015 Amethyst

3290 Thicket Brown

3300 Amber

2986 Mauve Orchid

2996 Primary School

3006 Lemon Zest

3016 Mountain Mist

3291 Desert Tan
3292 Smokey Quartz

3301 Royal Purple
3302 Ruby Red

2987 Blueberries
2988 King of Atlantis

2997 Mojito
2998 Florence

3007 Light Spearmint
3008 Green Tea

3017 Riverbed Slate
3018 Canyon Shale
101

Appendix
Choosing Your Fabric and Batting
Fabric
Some fabrics are not recommended for use with your quilting machine. Thick fabrics, such as denim or leather, have a lot of resistance that can bend or snap a needle, and misalign or break internal machinery. When quilting, avoid any fabrics that are difficult to pierce, and take care that the fabric layers of the quilt are well balanced.
Batting
To choose the best batting for your project, consider the look and feel of the quilt that you’re making. Batting thickness is measured by its loft. A low loft batting is thinner and lighter, ideal for a quilt with a flatter appearance. High loft batting should be used if a fluffy, full quilt is desired. Typically, wool batting is the thickest batting while bamboo is the lightest. Wool provides the most warmth, followed by polyester, and then cotton.
102

Troubleshooting Guide

Appendix

Issue
Machine won’t turn on. Stitches are skipped.
Thread is breaking.

Cause(s)
Loose cables
Machine is not turned on

Solution
Check that cables are securely plugged in (page 24).
Check power button is pressed down correctly (page 24).

If problem persists, please contact a Grace Company support technician. Call 800-264-0644.

Damaged needle

Check needle (page 72).

Machine improperly threaded
Bobbin wound or threaded incorrectly Incorrect thread tension
Hopping foot incorrect distance from needle plate

Check that all tensioners and guides were threaded correctly (page 33).
Check that the bobbin was inserted the correct direction in the case (page 30).
Adjust top thread tension (page 56). Adjust bottom thread tension (page 30).
Check distance with height gauge. Reinstall hopping foot if incorrect (page 74).

If problem persists, please contact a Grace Company support technician. Call 800-264-0644.

Damaged needle Incorrect thread tension
Machine improperly threaded
Stitching in place too long

Check needle (page 72).
Adjust top thread tension (page 56). Adjust bottom thread tension (page 30).
Check guides and tensioners for accidental double-wrapping (page 33).
Keep machine moving to avoid stitch build-up in one place, or switch to regulated precise quilting mode (page 43).

103

Appendix
Troubleshooting Guide (continued)

Issue

Cause(s)

Solution

Thread is breaking.

Bobbin inserted incorrectly Debris on tension discs

Check bobbin is the correct direction in the case and inserted firmly (clicked) into the machine (page 30).
Clean the machine (page 69).

Burred bobbin case

Check bobbin case for sharp edges. Contact your dealer to replace if needed.

Needle plate is rubbing needle

Check that needle plate is centered and does not hit needle (page 79).

If problem persists, please contact a Grace Company support technician. Call 800-264-0644.

Machine is running loud.

Machine and/or hook assembly Oil the machine and hook

needs oiling

assembly (page 69).

Bobbin winder is on

Press the “stop” button on the bobbin winder.

If problem persists, please contact a Grace Company support technician. Call 800-264-0644.

Thread is bunching up in

Bobbin wound or threaded

hook assembly (bobbin case incorrectly

area).

Check that the bobbin was threaded correctly and inserted the correct direction in the case (page 30.

Machine improperly threaded

Check that all tensioners and guides were threaded (page 33).

Incorrect thread tension

Adjust top thread tension (page
56). Adjust bottom thread tension (page 30).

Bobbin case has damaged or missing spring

Check inside bobbin case to see spring. Contact your dealer to replace if needed.

If problem persists, please contact a Grace Company support technician. Call 800-264-0644.

104

Index

Appendix

Index
Symbols
2.5 mm T-handle Allen wrench ………………… 2, 19, 21, 22 2 mm T-handle Allen wrench ………………………………… 92 3 mm T-handle Allen wrench …………………. 19, 27, 74, 89 4 mm Allen wrench………………………………………………. 8 4 mm Allen wrench (L-shaped) ……………………………….. 8 4 mm T-handle Allen wrench ……………… 2, 14, 16, 22, 86 7 inch touch display ……………………………………………. 19
A
adjust handles…………………………………………………… 16 adjust hopping foot ……………………………………………. 74 animated instructions………………………………………….. xv
B
back left wheel base cover …………………………………… 14 back right wheel base cover …………………………………. 14 back wheel base assembly …………………………………….. 8 basting ……………………………………………………………. 49 batting…………………………………………………………… 102 bobbin …………………………………………………………27, 84 bobbin case………………………………………………………. 30 bobbin case tension ……………………………………………. 31 bobbin estimator ……………………………………………….. 51 bobbin fill adjustment …………………………………………. 29 bobbin wind troubleshooting ………………………………… 84 bottle 68 bottom carriage…………………………………………………… 3 bottom thread tension ………………………………………… 31 brightness (needle area) ……………………………………… 41 brightness (screen)…………………………………………….. 41
C
calculator …………………………………………………………. 61 cleaning …………………………………………………………… 69 click sound ……………………………………………………….. 41 controls …………………………………………………………… 42 cruise sewing mode ……………………………………………. 45

encoder (lower)…………………………………………………… 2 encoder port …………………………………………………. x, 23 encoder spring ………………………………………………….. 86 encoder (upper) ………………………………………………… 22
F
fabric 102 factory reset……………………………………………………… 41 features …………………………………………………………….vii Finesse thread…………………………………………………. 101 firmware ………………………………………………………….. 83 flat-head screwdriver …………………………………….. 89, 92 front left wheel base cover …………………………………… 14 front right wheel base cover …………………………………. 14 front wheel base assembly …………………………………….. 8
G
getting started…………………………………………………… 63 grounding instructions ………………………………………….. ii guide loops …………………………………………………. 28, 35
H
handle adjustment……………………………………………… 16 handlebar assembly ……………………………………………. 16 handlebar controls ……………………………………………… 42 hand wheel ………………………………………………….. viii, ix help guides ………………………………………………………. 26 hook assembly …………………………………………. ix, 89, 92 hook holder………………………………………………………. 89 hopping foot …………………………………………………….. 74 hopping foot height tool………………………………………. 74
I
included parts and tools ………………………………………..xii
L
lamp ix, 41 large thread tensioner…………………………………………. 56 layout viii lint brush …………………………………………………………. 69

D

M

defaults …………………………………………………………… 40 display …………………………………………………………….. 19 display cable port ……………………………………………….. xi dual-wheel bottom carriage ……………………………………. 3
E
edge warning ……………………………………………………. 53 edge warning light……………………………………………… 41 edge warning sound …………………………………………… 41 electrical ……………………………………………………………vii encoder ……………………………………………………2, 22, 86

M4 x 8 mm SBHCS……………………………………………… 21 M6 shoulder bolt………………………………………………….. 8 M6 x 16 mm SBHCS……………………………………………. 15 M6 x 20 mm SBHCS……………………………………………… 8 machine dimensions …………………………………………….vii machine layout…………………………………………………..viii machine maintenance …………………………………………. 67 machine settings ……………………………………………….. 40 machine specifications ………………………………………….vii machine timing………………………………………………….. 92 manual sewing mode ………………………………………….. 47

105

Appendix
Index (continued)

measurements ………………………………………………….. 59 support………………………………………………………….. 103

metric 41

system info ………………………………………………………. 41

N

T

needle button……………………………………………………. 41 needle change…………………………………………………… 72 needle diagram …………………………………………………. 98 needle groove …………………………………………………… 98 needle magnet ………………………………………………….. 72 needle plate ……………………………………………………… 79 needle scarf ……………………………………………………… 98 needle size……………………………………………………….. 97 needle stop position……………………………………………. 41
O
oil bottle ………………………………………………………….. 68 oiling 68, 69 overspeed light………………………………………………….. 41 overspeed sound ……………………………………………….. 41
P
parts xii parts of machine ………………………………………………..viii power cable ……………………………………………………… 24 power cable retainer …………………………………………… 24 power port ……………………………………………………. x, 24 power switch…………………………………………………. x, 24 precise sewing mode ………………………………………….. 43 preferences ………………………………………………………. 40 processed threads ……………………………………………. 100 pull up bobbin thread………………………………………….. 63
Q
QuiltMotion tablet port ………………………………………….. x
R

thread …………………………………………………… 27, 33, 99 thread cutter ……………………………………………….. 28, 37 threading machine……………………………………………… 33 threading the machine ………………………………………… 33 thread size ……………………………………………………… 100 thread strength …………………………………………………. 33 thread tension ……………………………………………… 31, 56 timing machine………………………………………………….. 92 timing spacer ……………………………………………………. 92 tools xii track run time …………………………………………………… 62 track stitch count……………………………………………….. 62 troubleshooting guide ……………………………………….. 103
U
units 41 USB connector port………………………………………………. x
V
video instructions ………………………………………………. xv
W
wheel alignment ………………………………………………… 10 wheel base…………………………………………………………. 8 wheel covers …………………………………………………….. 14 wheel installation…………………………………………………. 8 wheels ………………………………………………………………. 8 winding a bobbin ……………………………………………….. 27
Y
yank test………………………………………………………….. 33

run time…………………………………………………………… 62

S

safety instructions ………………………………………………… i screen installation………………………………………………. 19 screwdriver …………………………………………………. 89, 92 settings menu …………………………………………………… 40 sewing mode: basting…………………………………………. 49 sewing mode: cruise …………………………………………… 45 sewing mode: manual…………………………………………. 47 sewing mode: precise …………………………………………. 43 single-wheel bottom carriage………………………………….. 3 specifications ………………………………………………………vii stitch count ………………………………………………………. 62 stitches per centimeter………………………………………… 41 stitches per inch ………………………………………………… 41

106

Information on the disposal for Waste Electrical & Electronic Equipment (WEEE): This symbol on the products and accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper disposal for treatment, recovery and recycling, please take these products to designated collection points where they will be accepted on a free-of-charge basis. In some countries you may be able to return your products to your local retailer upon the purchase of a new product. Disposing of this product correctly will help you save valuable resources and prevent any possible effects on human health and the environment, which could otherwise arise from inappropriate waste handling. Please contact your local authority for further details of your nearest collection point for WEEE.

www.graceframe.com 1-800-264-0644

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals