Kinco GH150E HMI Touch Screen 15 Inch Ethernet USB Host Instruction Manual

: June 12, 2024
: Kinco

Table of Contents

Installation Note
Installation Description
External Interface
After-sales Service
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

GH150E /GL150E HMI
Installation Instruction

Kinco GH150E HMI Touch Screen 15 Inch Ethernet USB
Host

Installation Note

1.1 Environmental Requirement
Operating temperature: GH150E/GL150E HMI can work stably in most industrial environments that the temperature between 14°F to131°F (-10~55°C).
NEMA rating: This Series HMI front panel is NEMA 1 rated.
Please do not use in the following places:

Places direct in sunlight
Surrounding temperature and humidity beyond the specifications
Places of temperature changes sharply and easily cause condensation
Places that exist corrosive gas and combustible gas
Places of much dust, dirt, salt and iron powder
Places that will be splashed water, oil and drugs

Pleasetakeshielding measures in the following places:

Places that exist electrostatic or other kinds of noise
Places of strong electromagnetic
Places that may be exposed to rays
Places near the power

1.2 Power Requirement

Input voltage:DC21V～DC28V.
Particularly note that there must be enough distance between this product and converters or switch mode power supply. Make sure that the input and output cables of that kind equipment are shield cable and the shielding network is connected with the ground.
Make sure that the DC power and AC power is isolated.
Do not use common power with perceptual load or input circuit of the controller.
Note: An Internal fuse will prevent damage for over voltage condition, however it isn’t guaranteed the internal electronic components are not damaged.

Installation Description

2.1Dimensional Drawing

Kinco GH150E HMI Touch Screen 15 Inch Ethernet USB Host - Dimensional
Drawing

Note: there is no indicator on the front panel of GL150E.
2.2 Fixed Screw Installation Instructions
The product is put into the well mounted hole of the machine control box’s panel, and the mounting screws are inserted into the fixing holes around the HMI shell from the back of the control box’s panel.
Recommended lock torque: 0.5N.m (to waterproof effect and avoid shell deformation)

Kinco GH150E HMI Touch Screen 15 Inch Ethernet USB Host - Dimensional
Drawing1

2.3 Power Connection
Before connecting the power, please make sure all local and national electrical standards are met. For power cables, please select cables with their dielectric strength values and current values in compliance with the safety specifications.
First find the power terminal at the back of the product and loosen the screw according to counterclockwise, then insert the power cables and tighten the screw up.
Connect positive DC line to the ‘DC24V’ terminal, the DC ground to the ‘GND’ terminal and the ground line to the ’FG’ terminal.

External Interface

Kinco GH150E HMI Touch Screen 15 Inch Ethernet USB Host - External
Interface

3.1 POWER (Back-shell）

Pin#	Signal
1	DC24V
2	GND
3	FG

3.2 SD CARD (Back-shell) (Only GH150E support)

Connection	Standard SD card interface
Port Function	The SD Card can be inserted in through this interface for

Data storage and user configuration uploading/downloading.

3.3 USB HOST

Connection	Connect with USB interface devices or U disks
Port Function	This interface can be connected with USB keyboard, mouse

and printers, and the U disk can be used for user’s configuration uploading/ downloading as well as data storage.

3.4 USB SLAVE
The interface type is Micro USB

Connection	USB Slave port can be connected with a PC
Port Function	The port is only used to download user configuration

program to the HMI and to set HMI system parameters.

3.5 COM0/COM2

Pin assignment of the 9-pin male, D-SUB, COM0/COM2.Note:
RS232/485/422 communication functions are supported by COM0.COM2 supports RS232 communication function.

（COM2） [RS-232]

---|---|---|---|---|---
1| Rx-（B）| RS422 R-| RS485 B| |
2| RxD_PLC| | | RS232 RxD|
3| TxD_PLC| | | RS232 TxD|
4| Tx-| RS422 T-| | |
5| GND| Signal ground
6| Rx+(A)| RS422 R+| RS485 A| |
7| RxD_PC| | | | RS232 RxD
8| TxD_PC| | | | RS232 TxD
9| Tx+| RS422 T+| | |

3.6 COM1/COM3(Only GH150E support)
Pin assignment of the 9-pin male, D-SUB, COM1/COM3.Note:
RS232/485/422 communication functions are supported by COM1.COM3 supports RS485 communication function.

Pin	Signal	COM1 [RS-422]	COM1 [RS-485]	COM1 [RS-232]	COM3 [RS-485]
1	Rx-(B)	RS422 R-	RS485 B
2	RxD PLC			RS232 RxD
3	TxD PLC			RS232 TxD
4	Tx-	RS422 T-
5	GND	Signal ground
6	Rx+(A)	RS422 R+	RS485 A
7	Rx-(B)				RS485B
8	Rx+(A)				RS485A
9	Tx+	RS422 T+

3.7 Ethernet
10M/100M adaptive Ethernet RJ45 port.

Connection	With CAT5 UTP cable connected to the Ethernet device.
Port Function	The port can be used for upload/download of HMI

configuration, setting of system parameters and online simulations of configurations. It can connect multiple HMIs via the Ethernet to form an HMI network. Furthermore, it can implement communications between HMI and PLC via the Ethernet, as well as communications with a PC via the Ethernet port.

After-sales Service

For < Service Terms and Conditions for HMI >, please check: http://www.kinco.cn

Kinco Electric (Shenzhen) Ltd.
Add：Building 1, No. 6 Langshan 1st Rd, Hi-tech Park North, Nanshan, Shenzhen, China.
Tel：0755-26585555
Fax：0755-26616372
http://www.kinco.cn
Email：sales@kinco.cn
PLC1.ir