Kinco GH104E 10 Inch Widescreen HMI Touch Panel Instruction Manual
- June 12, 2024
- Kinco
Table of Contents
GH104E /GL104E HMI
Installation Instruction
Installation Note
1.1 Environmental Requirement
Operating temperature: GH104E HMI can work stably in most industrial
environments that the temperature between 14°F to131°F (-10~55°C), 32°F
to122°F (0~50°C) for GL104E.
NEMA rating: This Series HMI front panel is NEMA 1 rated.
Please do not use in the following places:
- Places direct in sunlight
- Surrounding temperature and humidity beyond the specifications
- Places of temperature changes sharply and easily cause condensation
- Places that exist corrosive gas and combustible gas
- Places of much dust, dirt, salt and iron powder
- Places that will be splashed water, oil and drugs
Please take shielding measures in the following places:
- Places that exist electrostatic or other kinds of noise
- Places of strong electromagnetic
- Places that may be exposed to rays
- Places near the power
1.2 Power Requirement
- Input voltage:DC12V~DC28V .
- Particularly note that there must be enough distance between this product and converters or switch mode power supply. Make sure that the input and output cables of that kind equipment are shield cable and the shielding network is connected with the ground.
- Make sure that the DC power and AC power is isolated.
- Do not use common power with perceptual load or input circuit of the controller.
Note: An Internal fuse will prevent damage for over voltage condition, however it isn’t guaranteed the internal electronic components are not damaged.
Installation Description
2.1Dimensional Drawing
Note: there is no indicator on the front panel of GL104E.
2.2 Fixed Screw Installation Instructions
The product is put into the well mounted hole of the machine control box’s
panel, and the mounting screws are inserted into the fixing holes around the
HMI shell from the back of the control box’s panel.
Recommended lock torque: 0.5N.m (to waterproof effect and avoid shell
deformation)
2.3 Power Connection
Before connecting the power, please make sure all local and national
electrical standards are met. For power cables, please select cables with
their dielectric strength values and current values in compliance with the
safety specifications.
First find the power terminal at the back of the product and loosen the screw
according to counterclockwise, then insert the power cables and tighten the
screw up.
Connect positive DC line to the ‘DC24V’ terminal, the DC ground to the ‘GND’
terminal and the ground line to the ’FG’ terminal.
External Interface
3.1 POWER
Pin# | Signal |
---|---|
1 | DC24V |
2 | GND |
3 | FG |
3.2 SD CARD( Only GH104E support)
Connection | Standard SD card interface |
---|---|
Port Function | The SD Card can be inserted in through this interface for |
Data storage and user configuration uploading/downloading.
3.3 Ethernet
10M/100M adaptive Ethernet RJ45 port.
Connection | With CAT5 UTP cable connected to the Ethernet device. |
---|---|
Port Function | The port can be used for upload/download of HMI |
configuration, setting of system parameters and online simulations of configurations. It can connect multiple HMIs via the Ethernet to form an HMI network. Furthermore, it can implement communications between HMI and PLC via the Ethernet, as well as communications with a PC via the Ethernet port.
3.4 USB HOST
Connection | Connect with USB interface devices or U disks |
---|---|
Port Function | This interface can be connected with USB keyboard, mouse |
and printers, and the U disk can be used for user’s configuration uploading/ downloading as well as data storage.
3.5 USB SLAVE
Connection | USB Slave port can be connected with a PC |
---|---|
Port Function | The port is only used to download user configuration |
program to the HMI and to set HMI system parameters.
3.6 COM0/COM2
Pin assignment of the 9-pin male, D-SUB, COM0/COM2.
Note:
RS232/485/422 communication functions are supported by COM0.COM2 supports
RS232 communication function.
Pin | Signal | COM0 [RS-422] | COM0 [RS-485] | COM0 [RS-232] | COM2 [RS-232] |
---|---|---|---|---|---|
1 | Rx-(B) | RS422 R- | RS485 B | ||
2 | RxD_PLC | RS232 RxD | |||
3 | TxD_PLC | RS232 TxD | |||
4 | Tx- | RS422 T- | |||
5 | GND | Signal ground | |||
6 | Rx+(A) | RS422 R+ | RS485 A | ||
7 | RxD_PC | RS232 RxD | |||
8 | TxD_PC | RS232 TxD | |||
9 | Tx+ | RS422 T+ |
3.7 COM1/COM3( Only GH104E support)
Pin assignment of the 9-pin male, D-SUB, COM1/COM3.
Note:
RS232/485/422 communication functions are supported by COM1.COM3 supports
RS485 communication function.
Pin | Signal | COM1 [RS-422] | COM1 [RS-485] | COM1 [RS-232] | COM3 [RS-485] |
---|---|---|---|---|---|
1 | Rx-(B) | RS422 R- | RS485 B | ||
2 | RxD_PLC | RS232 RxD | |||
3 | TxD_PLC | RS232 TxD | |||
4 | Tx- | RS422 T- | |||
5 | GND | Signal ground | |||
6 | Rx+(A) | RS422 R+ | RS485 A | ||
7 | Rx-(B) | RS485B | |||
8 | Rx+(A) | RS485A | |||
9 | Tx+ | RS422 T+ |
After-sales Service
For < Service Terms and Conditions for HMI >, please check: http://www.kinco.cn
Kinco Electric (Shenzhen) Ltd.
Add: Building 1, No. 6 Langshan 1st Rd, Hi-tech Park North, Nanshan, Shenzhen,
China.
PLC1.ir
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>