FUJIOH FH-GS6320 SVGL Built-in Gas Hob Installation Guide

FUJIOH FH-GS6320 SVGL Built-in Gas Hob

Notice Before Use

For safety purpose, you should read the instructions carefully before using the appliance for the first time.
Save the instruction for future reference.

The appliance is designed for domestic use and may only be installed and operated in accordance with these instructions for use.

1. The gas hob must be installed by registered gas installer.
2. Ensure that the gas hob is used with good ventilation. Environment with insufficient oxygen should be avoided.
3. This gas hob is to be used for cooking only. Do not other use for other purpose.
4. During long period of use, open window or exhaust fan to ensure good ventilation.
5. Check that all control knobs have been set to “ ” position after use.
6. If the flame is blown out during use, the safety valve will cut off gas supply. Ignite again after at least 1 minute.
7. To avoid hazard, do not use spray or compressed gas when the gas hob is in use.
8. After ignition, check if the flame is even and normal.
9. Before removing cookware away from the flame, always set to small flame or turn the hob off.
10. Do not use burner racks other than the one provided. Otherwise, it will cause overheat to the range surface.
11. Do not use over-size or over-weight utensils to avoid damage.
12. Cooking utensils having more than 200mm and less than 320mm diameter can only be used.
13. Cooking utensils weighting less than 6kg (including food weight) can only be used.
14. And for burner rack (S),only cooking utensils with 8-14cm diameter is recommended.
15. Place the utensil steadily on the range burner rack. Do not tilt the utensil.
16. Contact our repair department for repair and parts replacement. During guarantee period, FUJIOH may charge for spare parts and service fees if the damage is caused by misuse or improper installation.
17. When installing built-in gas hob on top of kitchen cabinet, please check that there is provision for ventilation at the cabinet to ensure proper operation of the gas hob.
18. Dot not store any flammable materials, sprays or pressurized containers inside the kitchen cabinet.
19. The top panel of this gas hob is made of tempered glass which is safer than normal glass for this application. However, the following safety precautions for using gas hob with glass top panel should be noted in order to prevent the glass top panel from breaking:
    • Clean the burner assembly frequently to maintain a clear gas passage on the flame distributor, clean and tidy up the flame distributor after spillage of food and liquid once the burner assembly has cooled down.
    • Turn off the gas hob immediately if abnormal noise propagates from the gas appliance and contact gas supply company or gas hob importer for inspection.
    • Do not use oversized utensils for cooking.
    • Do not impact the glass surface with hard objects or place heavy objects on the glass surface.

Product Description

FH-GS6320 SVGL

FH-GS6330 SVGL

Installation Instructions

Attention
According to the Gas Safety Ordinance of Hong Kong, any gas installation works including the installation of appliances and connection tubing, must be undertaken by registered gas installers who are registered for that appropriate classes and be employed registered gas contractors.

Use approved gas tubing bearing EMSD approval marking (such as: fJ1Egifi~tlt;tEMSD APPROVAL GTXXXX) for connection to appliances, or other appropriate methods accepted by EMSD.

Attention
The gas hob must be installed by registered gas installer. Otherwise, FUJIOH will not be responsible for any damages.

• The inlet gas supply working pressure to the appliance MUST BE as follows:
  Type of gas Inlet pressure
  Hong Kong TG 1500 Pa
  Hong Kong LPG 2900 Pa

• If non-compatible pressures are connected to the appliance, it will affect the performance of the unit or pose risk of damage.

• Prior to installation, ensure that the appliance is according to the local distribution conditions (nature of the gas and gas pressure).

• This gas hob is not connected to ventilation devices for combustion products. It shall be installed according to the relevant regulations. Particular attention shall be given to the ventilation requirements.

• Install the gas hob in well ventilation room and keep it away from any combustible or flammable items such as paper or oil.

• Place the gas hob on a stable and level surface.
  If the unit is to be installed, close to combustible surroundings(such as wooden walls, wooden shelves), it should be installed at least 15cm from the side walls. The unit should be installed with a distance of at least 15cm away from surrounding combustible materials.

• External gas governor is not required.

• Aeration is preset at factory. Please do not attempt to adjust it.

Ventilation

Maintain normal gas combustion and the amount of air required for room ventilation, the air should naturally flow through the fixed windows or vents in the room.

When installing built-in gas hob on top of stove cabinet, please check that there is provision for ventilation at tfle cabinet to ensure proper operation of the gas hob.

Cut-Out Dimensions

Installation Diagram of Burner Rack & Burner Cap

Make sure that the following parts are fitted properly before use or after cleaning.

1. Burner Rack
   Fit Burner Rack legs into Drip Pan(Fig.1).
   

2. Burner head
   Install the Inner Burner Cap and Outer Burner Cap into Burner Head (Fig.2), do not tilt or leave gap during installation (Fig.3).
   

Attention

Operating Instructions

Attention

• All gas hob must be installed, commissioned and connected by registered gas installer. Do not install or repair the gas hob by yourself.
• Do not use additional fitting, such as aluminum foil may lead to abnormal operation.
• The safety sensor is very delicate-please do not use hard brushes or rough cleaning pads when cleaning.

1. User should check that this built-in gas hob has been properly installed by Registered Gas Installer.

2. This built-in gas hob is suitable for use with the specified type of gas(H.K. LP Gas or H.K. Town Gas).

3. Ignition:
   Make sure the flame controller knob” ” position, then open the gas supply valve. When igniting, press and turn the flame controller knob anti- clockwisely to 90 degree, the built-in gas hob will be automatically ignited. After ensuring the flame, the knob can be released and flame will retain, built-in gas hob must equipped with flame failure protection device. When flame has been distinguished accidentally, this protection device will work and the gas supply will stop accordingly for safety. However user please ensure that the indoor environment has sufficient ventilation. (Fig.GA)

4. Flame regulating
   Different size of flame can be obtained by regulating the turning knob. As Fig. 6A the power can adjust between “ ” and “ ” , and also can adjust from “ ” to ” ” , please adjust the flame slowly from high to low, to avoid the flame off.

5. Extinguish the flame
   Return the flame controller knob to • ® • position will extinguish the flame(Fig.6B). Please close the gas supply valve after use.

6. No igniton
   Please read “Troubleshooting”.
   

Troubleshooting

Dry the electrode with clean tissue or dry cloth.
Out of battery| Replace battery.
Flame cannot be held| Incorrect turning of gas control knob.| Press down and turn the control knob anti-clockwise towards “high” until “ticks” are heard. Release only after the hob is lit.
No flame| Gas meter cock and/or appliance isolating cock have been turned off .| Open gas meter cock and/or appliance isolating cock completely .
Yellow flame| Grease and dirt accumulated on burner cap.| Wash burner cap in warm water with detergent, mop it dry and then place back in correct position.
Unstable flame| Incorrect place of burner cap.| Refit burner cap into burner head base.
Smell of gas| Gas pipe is damaged or not connected well.| Stop using the appliance immediately. Shut-off gas emergency control valve and open the windows. Do not operate any electric appliances or switches. Do not use any phones on site.
Gas valve is leaking.

Warning: If the gas hob cannot be ignited by the above suggested solutions, do not attempt to ignite by other means. Please contact Gas Engineering Company for repair.

Specifications are subject to change without prior notice.

If there is any inconsistency or ambiguity between the English version and the Chinese version, The Chinese version shall prevail.

Refer to www.fujioh.com/hk/ for the most up-to- date version of the Operating Instructions.

Clean & Maintenance

Attention Do not cleaned, when the gas hob is hot.

Attention   Must be cleaned every three months or when the flame is unstable.

• Wipe the glass panel with a soft, damp cloth and mild detergent.
• Wash the burner head with warm water and detergent.
• Often clean the burner cap flame hole, keep clear.

Cleanable part

1. Burner Cap(L)
2. Burner Cap(S)
3. Drip Pan
4. Burner Rack
5. Burner Head Base
6. Glass Panel
7. Control Knob

Clean parts that can be removed

1. Burner Cap(L)
2. Burner Cap(S)
3. Burner Rack
4. Burner Head Base

Put the removed parts back in place after cleaning (Details on P.5)

Remove the parts for cleaning

Technical Specifications

Customer Support

Hong Kong Distributor
FIDELITY (FAR EAST) TRADING CO.,LTD.
Unit 13, 10/F, Technology Park, 18 On Lai St., Shatin N.T. Hong Kong
Tel:(852) 2686 8229
Fax:(852) 2637 0883

www.fujioh.com
FUJIOH INTERNATIONAL TRADING PTE.LTD.
130 Joo Seng Road #05-05 Singapore 368357
Tel: (65) 6286 3286 Fax: (65) 6285 3285
E-mail: [email protected]\

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>