FUJIOH FR-LW2490V Cooker Hood Instruction Manual

September 7, 2024
FUJIOH

FR-LW2490V Cooker Hood

Product Information

Specifications:

  • Main Unit Dimensions: 420mm x 325mm x 910mm
  • LED Light Dimensions: 485mm x 983mm
  • Optimal Distance from Wall to Center of Hob: 250mm

Product Usage Instructions

Installation

The cooker hood should be installed horizontally above the
cooking appliance. Refer to the installation diagram for proper
positioning.

Ensure that the hanging bracket, screws, and other components
are securely fixed in place.

Avoid placing the cabinet within the shaded area of the diagram
to maintain proper clearance.

Maintenance

Regularly clean the cooker hood and exhaust outlet to maintain
efficiency.

Check for any damages to the supply cord and contact the
manufacturer if replacement is needed.

Usage

Avoid allowing children to play with or operate the appliance
unsupervised.

Use the touch controls on the main unit to operate the cooker
hood effectively.

Ensure proper alignment of the cooker hood after installation to
prevent efficiency issues.

FAQ

Q: Can children use this appliance?

A: This appliance is not intended for use by children without
supervision due to safety concerns.

Q: How should I clean the cooker hood?

A: Use a damp cloth to wipe down the surfaces of the cooker hood
regularly. Do not use abrasive cleaners.

11 12 13 14 14

1

1

2

1.This appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or those lacking experience and knowledge, unless they are supervised or instructed on how to use the appliance by someone responsible for their safety.
2.Children must not play with the appliance. 3.Cleaning and user maintenance should not be performed by children without
supervision. 4.If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent, or similarly qualified persons to avoid a hazard. There must be adequate ventilation in the room when the cooker hood is used simultaneously with appliances that burn gas or other fuels. Do not use corrosive detergents for cleaning. Regular maintenance is necessary for the unit’s proper operation. To protect the main body from corrosion caused by the long-term accumulation of dirt, clean the cooker hood every two months using hot water and a non-corrosive detergent. There is a fire risk if cleaning is not carried out in accordance with the instructions. Do not use an open flame under the cooker hood. The air must not be vented into a flue that is used for exhausting fumes from appliances burning gas or other fuels. The minimum distance between the top most point of a cooking appliance, such as a gas hob, and the lower part of the cooker hood, when installed directly above the appliance, must be at least 300 mm. If a greater distance is specified in the manual of the cooking appliance, it must be taken into account. Regulations regarding air discharge must be followed.
Accessible parts may become hot during use with cooking appliances. This cooker hood is of the external exhaust type. The air from the hood should not be vented into the flue gas used for expelling smoke from burning gas or other fuels. If the cooker hood is installed above a gas hob, the distance from the bottom of the hood body to the cooking surface should be at least 300 mm, unless the installation instructions for the gas hob specify a greater distance. Modifying the product without authorization is strictly prohibited, and the power cord must not be replaced or modified independently. Do not install the cooker hood on a wall made of flammable material. Do not install the cooker hood directly above a gas hob that uses solid fuel. When drilling holes in the wall, avoid electrical wires embedded in the wall to prevent the risk of electric shock. A separate power socket rated for the cooker hood must be used, and it should be securely grounded. The product requires a minimum rating of 10A at 220V or above. The wall must have sufficient supporting strength for the installation of the cooker hood. For hollow core walls, the thickness should be greater than 30mm, while concrete walls can be directly drilled and installed. Ensure the product is securely mounted on the wall. The cooker hood may have sharp edges. Wear protective gloves when installing or cleaning it. If your kitchen is undergoing renovation or construction work, do not expose the cooker hood to building materials, dust, paint, coatings, or their volatile gases, as they can cause corrosion and loss of luster on the hood surface. Please install the cooker hood after completing the decoration.

This appliance is not intended for use by young children or individuals with physical limitations without supervision. Children should be supervised to ensure they do not play with the appliance. Plug the power cord into a socket outlet with an earthing continuity terminal. This cooker hood is intended for home use only and is not suitable for barbecue, roast shops, or other commercial purposes. The cooker hood and filter should be cleaned regularly as per the instructions. Do not use an open flame or allow flames to go beneath the appliance. Please maintain adequate ventilation in the room while the cooker hood is in operation. Before cleaning or maintaining the appliance, ensure that the power plug is disconnected from the socket or that the breaker is turned off. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or a similarly qualified person to avoid hazards. The power cord should be provided by the manufacturer or its authorized seller. Failure to clean according to the instructions may pose a fire risk. If the connecting wire is damaged, please contact the manufacturer, its service agent, or other similarly qualified technician. Use the product according to the instructions to avoid any hazards. The exhaust air must not be directed into a smoke flue or chimney used for ventilating fumes from appliances such as gas burners. Follow the local laws applicable for external air ventilation.
3

1 2 3 4 5 6 7 8 9 10 11 12 13

M8 S T 5 . 0 × 6 0 M4×10

1 1 1 1 6 6 2 1 1 1 1 1 1

LED

4

The following product components are attached to the product package. Please check them upon opening. If any components are missing, please contact the service center or your dealer.

Main Unit Hanging Bracket Exhaust Outlet

M8 Plastic Expansion Pipe

Screws ST 5.0X60

Screws M4X10

Instruction Manual

Pressing Plate

Oil Tray Slide Duct Cover Fixing Bracket

Slide Duct Cover

13

Duct Cover

Main Unit Touch Control

Slide Duct Cover Duct Cover
LED Light Oil Tray

350

340

420

315

150-380

150-380 With Slide Duct Cover

420

350
340 315

485 983

485 983
132

Ø180

895
895
Unit: mm

420

325

910

350

300400

78.5
Ø180mm

:125m m 40mm 250mm

5

132
Ø180

The cooker hood should be installed horizontally above the cooking appliance. Refer to the installation diagram below:

Unit: mm

Flexible tube duct Suspended ceiling
cabinet

420

325

910

350

300400

Diagram showing the opening of flexible tube duct in the ceiling.

78.5
Ø180mm
Center line of range hood
Installation diagram showing flexible duct tube connection to the cabinet. Place the cabinet outside the shaded area (as shown in the diagram). If the cabinet is placed within the shaded area, ensure a minimum clearance of 125mm and 40mm is reserved.
Optimal fume capturing efficiency is achieved with a 250mm distance from the wall to the center of the hob.

330 165

4×M 8 4 × S T 5.0

946 1 1 3 31 3 6 3

50

165 330

12461 3 4 6

300400

48

12461 3 4 6

48

After installing the cooker hood, ensure that both ends are aligned evenly. Avoid excessive breezes and air currents near the cooker hood, as they may affect its efficiency. The requirements for the exhaust pipe should be fulfilled. The exhaust pipe outlet should not be excessively long.

Cooker hood installation(Unit: mm)
1.Mark the mounting position of the hanging bracket according to the instructions provided below:

330 165

4×M8 Plastic Expansion Pipe
4×Screws ST5.0X60

50
Pressing Plate

48

946 1 1 3 31 3 6 3

Hanging Bracket Center Line

165 330

Cooker Hood Buttom

300400

Gas Hob Cooktop

Unit: mm

48

6

48 48

48mm70mm

70 8

3S T 5 . 0 × 6 0

4 8 m m 2
8m m 70m m

301.5

2×S T 5 . 0×6 0

70 8
M 8

2ST5.0×60

1° 2°
7

2.Drill holes with a diameter of 8mm and a depth of 70mm at the 4 marked screw positions, then insert the plastic expansion plugs into the holes.

70 8

Expansion Pipe

3. First fix the hanging bracket with 4 pcs ST5x60 screws.

4.Mark the location of the 2 screws on the wall, ensuring they are positioned 48mm from the top of the cabinet. Drill holes with a diameter of 8mm and a depth of 70mm, then insert the expansion plugs.

Slide Duct Cover Fixing Bracket 3 0 1 . 5

Plastic Expansion Pipe

70

Center Line

2×Screws ST5.0X60

8

M8 Plastic expansion pipe

Cooker Hood Buttom Gas Hob Cooktop

5.Use 2 ST5x60 screws to install the slide duct coverfixing bracket to the wall.

ST5x60 Screws

Slide Duct Cover Fixing Bracker

1S T 5 . 0 × 6 0

ST5.0×60

6.Install the main unit on the wall. Ensure that both the main unit and the wall are tilted 1 to 2 degree, so that the hook of the main unit hanging bracket can be fully inserted and secured into the slot. After hanging the cooker hood, verify its horizontal alignment and ensure the main unit is completely flush with the wall. Use another ST5×60 screw to secure the pressure plate to the upper part of the smoke deflector. This helps to locate and secure the smoke deflector, preventing it from dislodging or moving upwards during operation and maintenance, thus avoiding damage or dropping.

Trough Of Cooker Hood

Pressure Plate Hood

ST5.0×60 Screws

Plate

4
4

7.Place gasket at exhaust outlet (may need to removescrewsin advance) as shown below.Make sure thegaskets are aligned correctly. This step can be preparedin advance depending on the installation space
Hole Position

Hole Position

8.Insert the flexible tube ductinto the exhaust Outlet.There are four clasps between the fixed end oftheflexible tube duct and the exhaust port.Align with eachother and fasten the clasps clockwise

Align The Four Clasps

Turn Clockwise And Fasten

8 8

4 7 . 5 m m×1 0 0 0 m m

( )

4
9

9.Properly extend the exhaust pipe and direct it outdoors, minimizing the number of turns, preferably only once. Ensure the turning radius is large and gentle, avoiding tight, sharp bends. If your home has an existing check valve on the wall, connect the exhaust pipe to the check valve and seal it using the 47.5mm×100mm aluminum foil tape provided with the exhaust pipe fittings. If there is no check valve in the home, find a way to seal the outdoor exhaust port slightly below the indoor wall opening to prevent oil back flow.
Seal Here With Aluminum Foil Tape

Flexible Tube Duct
Exhaust Outlet

Check Valve (Need To Prepare Yourself)

10.Use tape to fix the power cable as shown.
Tape Power Cable

Warning
Do not run the power cable along the surface of the extended duct to avoid the risk of fire or electric shock.
Caution
Ensure that the installation screws are tightened; otherwise, fumes may leak. Properly control and extend the extended duct to lead outdoors with minimal bending (ideally one bend) and ensure the bending angle is greater than 120 degrees to avoid sharp angles. The outlet end should be positioned slightly lower to prevent oil reflux.

9

M4×10

Please remove the protective film before installation. Unscrew the four screws on the back and side of duct cover before removing the protective film. 11.To install the slide duct cover, lift it up from the main unit of the cooker hood and secure it to the bracket using the provided fixing screw set. Ensure the screws do not come into contact with the power cord during installation.
Slide Duct Cover
Slide Duct Cover Bracket
Slide Duct Cover inside
12.Insert the oil tray into the slot and push it all the way to the rear end of the product.

10

Oil tray
10

Control panel operation

/ ” “” ” ” ” ” ” ” ” ” ” ” ” F1″ ” F 1 – F 2 – F 3 – F b – F 1 ” ” ” ” 3 F b 1 F 3 F 1 ” ” F 2 ” “F3″ ” Fb” ” ” “30 1 0-5- 10 – 5 , 3 ” ” / ” ” ” ” ” “” ” ” ” ” ” 1 0 0~ 2 3 0 0 ~59 3 ” ” F 2 F 2 – F 3 – F b – F 1 – F 2 3
11

Power/Delay : When the power is turned on for the first time, the ” ” key will have
a faint light indicating that the power is on. After the power is on, press the ” ” key shortly to enter standby mode. While the power is on, press and hold the ” ” key to enable or disable
the gesture control. By default, the gesture control is enabled when the power is turned on for the first time. After the fan starts running, press the ” ” key shortly to activate the timer. While the timer is active, the ” ” indicator will light up. Press the ” ” key briefly again during the timer operation to turn off all operations (except LED light) and return to the power-on state.
Air flow : In standby mode, press ” ” to activate the fan operation. the operation
starts at F1 speed. Press ” ” to adjust the fan speed (sequence: F1F2F3FbF1). Press ” ” to shut down the fan directly, or press ” ” shortly to
activate the 3-minute timer function. When Fb (boost mode) is activated, it lasts for 1 minute. Upon
completion, it automatically switches to F3. F1: ” ” light, F2: ” ” light, F3: ” ” light, Fb: ” , , ” lights together.
Heat Clean:
In standby mode, briefly press ” ” to enable or disable the heat clean function. The heat clean cycle lasts for 30 minutes. When the heat clean is activated, the cooker hood flap opens. The heat cleaning function is enabled, and the ” ” indicator lights up.
Lighting/Clock Settings :
The lighting is independently controlled. Press the ” ” in any state to turn the LED lamp on or off.
In standby mode, press and hold the ” ” key to activate clock setting. While setting the clock, the hour segment of the time display will blink. Press the ” ” key briefly again to switch to minute setting mode, and press the ” ” key once more to exit time setting mode. While in hour or minute setting mode, press the ” ” key to increase the value, and press the ” ” key to decrease it. Each short press adjusts the time by 1 unit; holding down the key allows continuous adjustment. The hour
11

setting ranges from 00 to 23 in cycles, while the minute setting ranges from 00 to 59. If there is no operation, the system automatically exits time setting mode after approximately 3 seconds. During clock setting, the ” ” indicators blink to indicate the mode.
Gesture Control: Wave the hand from left to right for the first time to turn on lighting and
fan operation at F2 Continuously wave from left to right to change the fan speed in the
sequence of F2-F3-Fb-F1-F2. If both the fan and lighting are on, wave from right to left for the first time
to activate a 3-minute delay timer function. Wave from right to left again to turn off the fan directly and switch off the
lighting. The gesture function does not apply to the heat cleaning function.
Troubleshooting

The light turns on, but Fan switch has been turned off. Switch on the fan operation.

the motor does not Fan switch has failed.

operate.

Motor has failed.

House fuses have blown.

The Cooker hood is tilted.

Broken or faulty LED.
The distance betweenthe cooker hood andthe hob top is too far.

Any electrical repairs to this appliance must comply with local, state, and federal laws. Please contact the service center if you have any doubts before attempting any of the above actions. Always disconnect the unit from the power source before opening it.
12
12

13

Gloves
1.The heat clean function only cleans the oil of thecasing inside the cooker hood, and does not directlyclean the grease filter.
2.The automatic cleaning function only cleans the inner impeller of the cooker hood by heating it at high temperature.
Oil Tray
13

220-240V~/50Hz

159 93 72 50
160 95 74 51 161 96 75 52

××

8 5 3×1 5 2×5 ( m m )

8W

12V

14

(m³/h)
1200 1035 870 740 1200 1040 865 740 1200 1040 870 740

(dB(A))
52 48 45 40 52 48 45 41 52 48 45 41

Periodically clean the surface of the cooker hood with a damp cloth and neutral detergent. Unplug the power cable before cleaning.

Switching Circuit Waving Lntelligent Switch Electric Heating Tube

220-240V~/50Hz

E Yellow And Green

LED
Motor

Red
Black Red White Black

Orange White Black
Red
Blue
Blue
Red Motor
Black

Rated Voltage

Power Consumption Air flow

159

1200

52

93

1035

48

72

870

45

50

740

40

160

1200

52

95

1040

48

74

865

45

51

740

41

161

1200

52

96

1040

48

75

870

45

52

740

41

853×152×5(mm) 8W 14

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals