PIKO 55 Powerful Show Laser User Manual

PIKO 55 Powerful Show Laser

Please spend a few minutes to read this manual fully before operating this laser!

Legal notice

Thank you for purchasing this Ray Technologies product.
Due to continual product developments and technical improvements, Ray Technologies GmbH reserves the right to make modifications to its products. This manual and its content have been made with due care but neither Laserworld (Switzerland) AG nor its subsidiary Ray Technologies GmbH cannot, however, take any responsibility for any errors, omissions or any resulting damages forthwith.
The brands and product names mentioned in this manual are trade marks or registered trade marks of their respective owners.

Attention: This device is a show laser device for commercial use. This device is not a laser pointer, not suitable for pointing purposes and must not be used as a laser pointer.

Security Label

Please read manual before operation.

1. Laser radiation! Avoid exposure to beam
2. Laser class 4
3. Caution of radiation if cover is removed
4. Model type
5. Production year
6. Output power
7. Wavelength
8. Power supply & consumption
   

Front Panel

• A. Laser aperture
• B. Beam block
• C. Emission led
  

Back Panel

1. ILDA Out
2. ILDA In
3. Show NET / FB4 Interface
4. Loop for safety cord
5. DMX In
6. DMX Out
7. Interlock In
8. Interlock Thru
9. LAN: Computer connection
10. LAN: Computer connection
11. Control Pad
12. Power In
13. Power Out
14. Fuse
15. Key switch
    

Find information on how to operate your laser here: https://www.laserworld.com/en/online-manual

Product and package contents

Please check if all listed parts are included and undamaged. Included in delivery: Laser system, power cable, key, interlock bridge plug, manual, technical datasheet.

Preliminary warning notices

1. Please use this device only according to these operating instructions.
2. Do not use the device if there are any visible damages on housing, connector panels, power supplies or power cords.
3. This device must not be permanently connected to mains. Disconnect it from mains.
4. Never look directly into the light source of a laser projector. Danger of damage to the eyes or even blindness in extreme circumstances!
5. Do not operate the device at high humidity or in the rain or in dusty environments.
6. Protect device against dripping or splashing water. Do not place any liquid filled containers near to this device.
7. This product is specified for operation between +5 °C and +45 °C (max. +35 °C for RTI PIKO 55 & RTI PIKO 27G) environmental temperature only. The device must also not be exposed to direct sunlight. The ventilation system of the laser must not be blocked at all to prevent overheating. If the device shall be operated in higher or lower environmental temperatures or in direct sunlight, an additional housing with climate control functionality is required. In this case please contact the manufacturer for assistance.

Any warranty claims are void if the warranty label is removed or tampered with in any way.

Initial operations, safety instructions

1. Make sure to use correct voltage; see information on device & in this manual.
2. Make sure that the device is not connected to mains during installation.
3. Installation has to be done by technical experienced and qualified persons according to safety regulations of the respective country.
4. Always ensure that maximum permissible exposure (MPE) is not exceeded in areas accessible to the public or members of staff.
5. In some countries an additional inspection by technical control institutes could be necessary.
6. Connect an easily accessible interlock connector or circuit breaker to the projector.
7. The power supply should be easily accessible.
8. When installing the laser mount it with a minimum distance of 15 cm from walls and objects.
9. For safe setup e.g. on walls or ceilings please use a safety cord. The safety cord should be able to withstand tenfold the weight of the device. Please follow the accident prevention regulations of professional associations and/or comparable regulations for accident prevention.
10. If the device has been exposed to great temperature changes, do not switch it on immediately. Condensation (or any moisture/water formed) may damage this device.
11. Never use dimmer, RC or other electronically switched sockets. Whenever possible, do not use the laser projector together with large appliances (especially fog machines) on the same mains!
12. Ensure sufficient ventilation and do not place the device on any warm or heat radiating surface. Especially the ventilation openings must not be covered!
13. Ensure that device does not get overheated. Make sure that the device is not exposed to spotlights (especially moving heads). Heat of spotlights could overheat laser in a little while and leads to a degradation of performance.

Working on the device

1. This product has no user serviceable parts inside and should only be maintained and serviced by a qualified engineer.
2. Be sure that the mains plug is not connected to the power supply while installing the device.
3. Take off all reflecting things like rings, watches, etc. before starting to work with or at the projector.
4. Only use non-reflecting tools to work on device.
5. Wear protective clothing (like goggles, gloves etc.) according to laser power and wavelength of the laser.

Service notes

• Moisture and heat can reduce lifetime of the laser system dramatically and expires any warranty claim.
• Quick on/off switching of this device will reduce durability of the laser diode dramatically.
• Avoid sharp knocks and shocks to this device an ensure sufficient protection during transportation. Look after your Laserworld product.
• To increase durability of your laser, protect device against overheating:
  • Always ensure sufficient ventilation.
  • Do not face spotlights (especially moving heads) to the device.
  • Check temperature after approx. 30 minutes with each new installation. If necessary install the projector at a place with different temperatures.
  • Keep the device dry. Protect it from moisture, rain and damp.
  • Switch off device when it is not needed. Diodes are switched on and can wear out even if there is no visible laser output.
• Please ensure the fans and heatsinks are clear from dust and debris otherwise the risk of overheating may occur. If the unit or air inlets appear to be blocked, please contact a qualified service engineer to maintain and service the product.
• Removal of the warranty label as well as damages to the device caused by improper handling, neglect of the safety instructions and service notes will void the warranty.

General Operation

1. Power
   Connect the power cord to the device and to the mains. Make sure that your device is provided with the correct voltage. Wrong voltage could lead to irreparable damages. Please find the correct voltage data in the synoptical table at the end of this manual. Make sure that the device is not directed to people or inflammable objects during installation. To start the device, connect the interlock bridge, insert the key and switch it on, and switch the device on. The “Emission – Laser on“ LED at the front side of the device begins to light up when the device is ready for use.

2. Key Switch
   There is a key switch at the back of the laser system. Please plug the key to the switch and turn it on. The laser device only runs when the key is inserted and switched on. Prevent misuse! Unplug the key when the laser is unattended to prevent misuse of the system.

3. Fuse
   There is a fuse at the back side of the device. If the fuse should blow, please exchange it with a new one. If the problems recurs, please contact your dealer or the Laserworld service department.

4. Modes / Functions
   The different operation modes can be selected by using the rotating selector next to the ShowNET-Display (or FB4) at the back of the device. Any change of the operation mode for ShowNET devices requires a restart of the device (disconnect power and reconnect it again). Do not change any ShowNET-Display settings during operation, as random and dangerous laser output can occur.

5. Turn device off
   To turn off the device, turn the key to ‚OFF‘ and disconnect the power cable from the mains.

Operation Modes

This laser system can be operated in many different operation modes.
Information, videos and tutorials are available online!

Control Pad

The device is equipped with a control touchscreen, the following images explain the use of the touchscreen. Touch the screen to change the settings.

Starting sequence

Main Menu

Color Settings

Scanner Settings

Final statement

RTI products are tested and product packaging is inspected before leaving our warehouse. Users must to follow the local safety regulations and warnings within this manual and adhere to any regulations within its place of use. Damages through inappropriate use will void any liability or warranty of our products.
Due to continual product developments, please check for the latest update of this product manual at www.laserworld.com. If you do have any further questions, then please contact your dealer/place of purchase or use our contact section on our website.
For service issues, please contact your dealer/place of purchase and ensure only genuine Laserworld spare parts are used in any service repairs.

Errors and Omissions excepted and products are subject to change.

Ray Technologies GmbH
Mühlbachweg 2
83626 Valley / Germany

Managing Director: Martin Werner
Commercial Register: Distric Court Munich, HRB 197665
VAT ID: DE 276583486
www.raytechnologies.com
info@raytechnologies.com

References

• Startseite - LaserAnimation Sollinger
• Laser Systems and Laser Show by Laserworld - lasershow, showlaser, laser display, entertainment laser, dj laser, club laser, laser rental, showcontroller, laser software
• Bedienungsanleitung
• Laser User Manual

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>